Home » Pfaff » Sewing Machines » Pfaff hobby 350p

Pfaff hobby 350p Support Question

Find answers below for this question about Pfaff hobby 350p.
Need a Pfaff hobby 350p manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by randomarts22 on February 9th, 2020

Needle Clamp Holder

A needle might be stuck inside the needle clamp holder. Can I order a new one or is there a way to get it out?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Troubleshooter101 on March 3rd, 2020 1:58 AM

This answer was accepted by the poster of the original question.

Troubleshooter101

Member since:
September 30th, 2015

Points: 2,927,060

1,100
points

There should be a screw type tightener. If you can't loosen it with your hands, sometimes a screwdriver or a quarter held with a plyers are needed. Either way, you should be able to get it out. If it's in the plate on the bottom, that comes off with smaller screw drivers

Use this link for assistance:

https://sewing-machine-service-and-repair.com/needle-bar-damage-from-over-tightening

If any of this not helps you than order a new one.

Thanks

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101

Related Pfaff hobby 350p Manual Pages

Owner's Manual - Page 4

... operate where aerosol (spray) products are being administrated. • To disconnect, turn all instructions before relamping. The wrong plate can cause the needle to break. • Switch the sewing machine off ("0") position, then remove plug from the electrical outlet when removing covers, lubricating, or when making any air openings blocked. To unplug, grasp...

Owner's Manual - Page 5

Needle clamp holder 5. Accessory storage 8. Power switch 4. Clear fabric cover with needle guard 10. English Table of Contents Table of Contents 3 Overview of the machine 3 Accessories 4 Setting Up 4 Attaching the power cord and foot control4 Machine speed 4 For the USA and Canada 4 Cloth Presser 5 Getting Started 6 Fabric and trims that can be used 6 Laundering embellished ...

Owner's Manual - Page 6

... and Canada This sewing machine has a polarized plug (one way. If it still does not ﬁt, contact a qualiﬁed electrician to the foot control or motor. Do not modify the plug in the outlet, reverse the plug. Screwdriver 2. 1,5 mm Allen wrench 3. When not in use , or when making any way. 4 Needles 4. If the plug...

Owner's Manual - Page 7

... must move freely under the cloth presser. 2. M= medium position for heavy or thick fabrics. 4. Place the cloth/fabric/materials on the presser bar aligns with needle guard without any restrictions. 5 Loosen the cloth presser height adjusting screw to prevent cloth/fabric/ materials from lifting during the felting process. 1. Tighten the clear...

Owner's Manual - Page 8

...-washing ﬁbers before sewing does not apply. The best characteristic for fabrics is a natural ﬁber, to allow for best results. 6 With this needle felting machine! Getting Started Let your ...the ﬁnished sample the same way you intend to a natural ﬁber/napped surface/or mixed ﬁber base. With the needle felting machine, you plan on your projects even...

Owner's Manual - Page 9

... and out of the project. Experiment ﬁrst on either the right or the wrong side of the project. Make sure that will never break needles placing or removing your projects are very easy to place into the felting area and very easy to be up position, your project. 7 English Start...

Owner's Manual - Page 10

..., pant legs, and small areas that has accumulated from felting. Accessory Storage Open the accessory storage compartment by sliding it to the left and the machine will also give you to a free arm. Flat Bed Extension / Free Arm Remove the ﬂat bed extension by pulling the drawer forward...

Owner's Manual - Page 11

...the top of the needle touches the top of needles. Insert the new needle(s) until the needle bar is exclusive for the needle felting machine. Loosen the front needle clamp holder ﬁxing screw by turning the 1.5mm Allen wrench counter-clockwise and remove the needle(s). To remove the individual outer needles, loosen the needle ﬁxing screw on the needle clamp by turning the...

Owner's Manual - Page 12

Groove (inside holder) Cleaning the lint box Slide the ﬂatbed extension to the left to use the machine. Note: Replace the clear fabric cover with needle guard and presser height adjusting screw before removing it from the machine. 2. Tighten the needle clamp screw clockwise with the same type rated, MAX 15W. Make sure that the light bulb...

Owner's Manual - Page 13

... not cover any defect or damage caused by use of the needle plate? 4. Speciﬁcations Needle: #S1037 Number of needles: 5 Needle Clamp: Round type Feeding: Manual Light bulb: MAX 15 W Measurement: 435mm x 189mm x 292mm Weight: 5.6 kg We reserve the right to change the machine equipment and the assortment of accessories without prior notice, or make...

Owner's Manual - Page 55