Home » Pfaff » Sewing Machines » Pfaff GrandQuilter 18.8

Pfaff GrandQuilter 18.8 Support Question

Find answers below for this question about Pfaff GrandQuilter 18.8.
Need a Pfaff GrandQuilter 18.8 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by Chrisgold2020 on February 17th, 2022

Service Manual

lloking to find a parts manual and a service manual with electrical schematic for a Pfaff 18.8 grandequilter

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on February 18th, 2022 7:23 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,615,400

1,090
points

https://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/GrandQuilter_18-8-manual-EN.pdf?ext=.pdf

page 15 onwards

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff GrandQuilter 18.8 Manual Pages

Owner's Manual - Page 2

... the carriage 3 Remove the packing attached to your machine 3 Light Fixture ...4 Your Thread Stand 5 Belt guard ...6 Attaching your handle bars with controllers... Hopping Foot 9 Routine Cleaning and Oiling 11 Bobbin Winder and Bobbins 12 Machine Part Names 15 The Control Unit 16 Threading Overview 17 How Do I Thread the Machine 17 How Do I Change the Needle 20 How Do I Make Adjustments to...

Owner's Manual - Page 3

... for it to roll one way or another as the frame may not be level when you place the machine on there and you should ever need to ensure that you center the machine on the carriage. You will find a rubber mat shipped with the box in case you want to ship...

Owner's Manual - Page 4

... bracket. Tighten the nuts on the base of the lamp to secure the lamp to your machine, Step 1. Trim the cord flush. Light Fixture To add your light fixture to the lamp support bracket on ...the side of your machine. Loosen the nuts so that you can slide the lamp fixture into the space provided on your lamp....

Owner's Manual - Page 5

Your Thread Stand Your Grand Quilter 18.8 comes with the two screws provided. Some assembly required. On the side of the machine you will see where to the side of your machine with a four spool thread stand. Now you will need to attach your thread stand to connect. On the side of the thread...

Owner's Manual - Page 6

... are the screws used to your motor sensor and protect you will find the plastic cover and attached to the machine are two above the hand wheel and one can be found below the hand wheel. Step 2. In the box you from getting caught in the ...

Owner's Manual - Page 7

...on the front of the machine or the needle side of the machine and is used when following... a pantograph with your Mega Quilter 18x8. Step 3. Step 2. If you can connect your handle bars with controllers to your Mega Quilter 18x8. Remove the two hex screws from the block using the allen wrench provided in place on the block and place the front part...

Owner's Manual - Page 8

...) and Controls on the Handles For one year after the purchase of the Pfaff GrandQuilter 18.8 longarm sewing machine, we will repair or replace (at our option), without the encoders and cables... Assembly (Deck) comes without any cost to you for either parts or labor, any machine or part that proves to connector on the back of the machine. The next one up is not covered under warranty. Any ...

Owner's Manual - Page 9

...1 thin dimes worth of space between the bottom of the foot and the fabric or base of your machine. 9 Because there is in the foot. What is where you lift the lever. This is the Tension...tension disc plates open as you adjust the hopping foot for Thicker or Thinner Batting? NEVER start sewing with the lever up. The tension release lever raises the hopping foot and releases the tension on...

Owner's Manual - Page 10

Next you will adjust the walk by loosing this bolt so that you tighten the bolt. 10 Loosen this bolt here To move this in the lowest position.) More Walk (higher) Less Walk (lower) Replace the side cover after you can move this arm up and down. Note: (Machine is shipped with this part up .

Owner's Manual - Page 11

... stitches, shredded thread and a weakening of oil please purchase from Grand Quilter 18.8. (Note: the machine pictured here is before complete assembly from around . We suggest using a soft...point top of oil in this time make sure oil is present on your quilting machine. Run machine to 4 drops of machine Oil Reservoir with dip stick Oil Dip Stick Oil Reservoir with dip stick removed 11...

Owner's Manual - Page 12

.... 4. A sloppy or mushy wound bobbin will result in poor stitch quality. Place a cone of thread. Bobbin Winder and Bobbins A bobbin winder is included with your machine. Bring the thread up through the bottom thread guide. 12 The thread on a properly wound bobbin should be snug and have even layers of thread...

Owner's Manual - Page 14

... to run at all, it needs more tension. Draw the thread down the thread. Turn your machine past the take up in the bobbin case especially with cotton threads. Holding the bobbin case pull ...of thread and watch as the thread flows out of the bobbin case. Insert the bobbin into the machine: 1. Always listen for the pop as it to build up lever and remove the bobbin case, place...

Owner's Manual - Page 15

... Spring 5. Silver Angle Bracket 7. Thread Guide 9. Needle 6. This guard is a diagram of the side of your machine has the electrical outlet and stitch regulator plugs. Thread Guide 10. Machine Part Names ( Please note: the takeup lever guard has been removed for a clear view for pictures only. Thread Eyelet Above the Needle 11. The back...

Owner's Manual - Page 16

... and needle down . So if the needle up is detected and the speed of the machine will cycle and you can now pull you can be found on either controller. To activate the manual stitch, press the manual stitch button and ensure that has a light under the button is on the left side...

Owner's Manual - Page 17

... the guard in this area. Figure 1 Figure 1 17 Place a cone of thread. Make sure the eyelet is not a handle. How Do I Thread the Machine? 1. Keep your hands clear as you will get pinched if your fingers get in place, extreme head injury may occur. Pull thread through eyelet above ...

Owner's Manual - Page 18

... catch the check spring. Be sure the thread is in picture. The check spring should come down as shown on three hole thread guide. Figure 4 18 Up and over the check spring. Weave thread as you pull thread. Figure 2 3. Thread upper thread guide as shown in the tension disk. Take thread...

Owner's Manual - Page 19

... front to thread the guide directly above the needle. 6. Thread runs under silver angle bracket. Figure 4 Takeup lever guard removed for details. Never run the machine without the guard in place, extreme head injury may occur. Figure 6 Figure 6 19 Take thread through the take up through the thread guide just above...

Owner's Manual - Page 20

... the hand wheel a complete turn your machine. 20 Before you tighten the screw. Your home sewing machine needle shank (top of the old needle into the bobbin case, the hook comes around behind the needle to pick up in the bobbin area rotates with your Grand Quilter 18.8 from the factory. back of the...

Owner's Manual - Page 21

... deflect. The higher the tension, the more tension on the top than a home sewing machine presser foot because the fabric must be able to press and sew multiple layers together while the machine head is in different directions as a home sewing machine except the quilter is the bottom tension. If the pokies are where you can...

Owner's Manual - Page 25

... spring Fig 16: New spring in place Fig 17: Insert the tension assembly back in barrel Fig 18: Insure that your check spring is at 11:00 (refer to fig 26 for your machine Fig 22: Once in ensure that you are all the way in and notice the tension disk opens...