Home » Pfaff » Sewing Machines » Pfaff GrandQuilter 18.8

Pfaff GrandQuilter 18.8 Support Question

Find answers below for this question about Pfaff GrandQuilter 18.8.
Need a Pfaff GrandQuilter 18.8 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by sindelarmarlys on March 31st, 2022

Pfaff Grand Quilter 18.8

where can I find a replacement encoder for pfaff grand quilterT82; 18.8 encoder?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on March 31st, 2022 7:54 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,617,810

1,100
points

http://www.myqbot.com/accessories_18.html

https://www.allbrands.com/products/32168

https://www.sewingpartsonline.com/pfaff-grandquilter-18-8-sewing-machine-parts.aspx

https://www.sewingpart.com/category-s/23272.htm

https://www.ebay.com/itm/162128183295

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff GrandQuilter 18.8 Manual Pages

Owner's Manual - Page 2

... 3 Remove the packing attached to your machine 3 Light Fixture ...4 Your Thread Stand 5 Belt guard ...6 Attaching your handle bars with controllers 7 Connecting your Mega Quilter 18x8 to your carriage assembly (deck) and... and Oiling 11 Bobbin Winder and Bobbins 12 Machine Part Names 15 The Control Unit 16 Threading Overview 17 How Do I Thread the Machine 17 How Do I Change the Needle 20 ...

Owner's Manual - Page 3

... mat shipped with the box in case you have the encoders attached to ship this machine. 3 Placing your machine on the carriage. Place the mat on the carriage before placing your machine on the carriage. Remove the packing attached to your machine to help keep the machine from slipping on the carriage you want to ensure...

Owner's Manual - Page 4

...don't need to reach the outlet on top of the power box on your machine. Loosen the nuts so that you can slide the lamp fixture into the space provided on the machine in the lamp support bracket. Measure the cord so that you have any wires ... tab and open the plug. Find the plug which is shipped with enough to your lamp. 4 Open your machine. Lay the wires in the space provided in your...

Owner's Manual - Page 5

... you will see two screws where you will need to attach your machine with a four spool thread stand. Now you will see where to the side of the thread stand. You will place the base of your thread stand to connect. Your Thread Stand Your Grand Quilter 18.8 comes with the two screws provided.

Owner's Manual - Page 6

... 4. Replace the three screws so that they hold the belt guard in place. This photo shows the belt guard in the belt. Locate the screws on the machine there are the screws used to the machine are two... 2. Locate the belt guard and position over the hand wheel and the motor. Belt guard Your machine comes with a belt guard to prevent damage to your motor sensor and protect you will find the...

Owner's Manual - Page 7

...This block is on your Mega Quilter 18x8. Step 1. If you . Remove the two hex screws from the block using the allen wrench provided in place on the front of the machine or the needle side of the...hold the handle bars in your accessory bag. Step 3. Center the handles on the back of the Machine or the motor side of the screws being tight ensure that will come off. This block is ...

Owner's Manual - Page 8

... Controller on your handle bar have a sheet with care. Connecting your Grand Quilter 18.8 to your Carriage Assembly (Deck) and Controls on the Handles For one year after the purchase of the Pfaff GrandQuilter 18.8 longarm sewing machine, we will repair or replace (at our option), without the encoders and cables connected. Such damage is not used at the back...

Owner's Manual - Page 9

...hopping foot and releases the tension on the thread the bottom stitches will be huge loops. The walking of your machine. 9 This is no tension on the thread. You can watch the tension disc plates open as you adjust the... of space between the bottom of the foot and the fabric or base of the machine. NEVER start sewing with the lever up. First remove this cover from the side of the...

Owner's Manual - Page 10

Note: (Machine is shipped with this in the lowest position.) More Walk (higher) Less Walk (lower) Replace the side cover after you can move this arm up and down. Loosen this bolt here To move this part up . Next you will adjust the walk by loosing this bolt so that you tighten the bolt. 10

Owner's Manual - Page 11

... lint can mean skipped stitches, shredded thread and a weakening of machine oil on your machine has more drops of oil please purchase from Grand Quilter 18.8. (Note: the machine pictured here is present on the brush. By using a soft bristle brush to the longevity of machine Oil Reservoir with dip stick Oil Dip Stick Oil Reservoir with...

Owner's Manual - Page 12

... the tension disk and through the guide over the cone of thread on the holder. 3. Bobbin Winder and Bobbins A bobbin winder is included with your machine. A sloppy or mushy wound bobbin will result in poor stitch quality. Place a cone of thread. 4.

Owner's Manual - Page 14

...A tiny amount of oil in the bobbin hook area before you start quilting, unthread your machine on the brush. Check the bobbin each time you begin quilting. To place the bobbin into... small drop of lint can cause a huge headache! With one hand. Insert the bobbin into the machine: 1. Be very careful not to keep it needs more tension. Holding the bobbin case pull the ...

Owner's Manual - Page 15

... Up Lever 8. Thread Eyelet Above the Needle 11. Do not place your hand in place, extreme head injury may occur. Tension Disc 4. Never run the machine without the guard in this ) 2. The front of your fingers will get pinched) This is not a handle. Thread Guide 9. Thread Guide 10. Thread Guide 15...

Owner's Manual - Page 16

... the left side is on either controller. So if the needle up and it lit and the machine will adjust to the top. Right controller with Auto Stitch (stitch regulation) and Manual Stitch Knob .... Knob adjust speed when in Auto Stitch. Left controller with needle up or down . As the machine is moved movement is lit. To activate the manual stitch, press the manual stitch button and ensure...

Owner's Manual - Page 17

... hands clear as you will get pinched if your fingers get in place, extreme head injury may occur. How Do I Thread the Machine? 1. Figure 1 Figure 1 17 Never run the machine without the guard in this area. Pull thread through eyelet above the thread cone. Place a cone of thread. Make sure the eyelet...

Owner's Manual - Page 18

... thread tightly to ensure the thread is going between the two tension discs from back to catch the check spring. Figure 3 Figure 3 Figure 4 5. Figure 2 3. Figure 4 18

Owner's Manual - Page 19

... thread up lever from back to back. Take thread through the take up through the thread guide just above the check spring. 6. Never run the machine without the guard in place, extreme head injury may occur. Bring the thread down through the thread eyelet directly above the needle. Figure 4 Takeup lever...

Owner's Manual - Page 20

... to replace the needle you are placing the scarf of the machine and turn the hand wheel a complete turn your machine. Be sure the power switch is time to the back of your Grand Quilter 18.8 from... it is off on the machine. Look closely at the back of the long arm machine needle is up in place while you insert the needle. Your home sewing machine needle shank (top of the...

Owner's Manual - Page 21

... slide between the quilt top and backing. Tip: A general rule of fabric being sewn. Understanding how your long arm machine makes a stitch will see tiny dots of point you use , such as a home sewing machine except the quilter is the bottom tension. The higher the tension, the more tension on the top than a home...

Owner's Manual - Page 25

... new spring Fig 16: New spring in place Fig 17: Insert the tension assembly back in barrel Fig 18: Insure that your check spring is at 11:00 (refer to fig 26 for your machine Fig 22: Once in ensure that you feel resistance on the check spring Fig 20: Tighten screw.