Pfaff C1100 Pro Support Question
Pfaff C1100 Pro Support Question
Find answers below for this question about Pfaff C1100 Pro.Need a Pfaff C1100 Pro manual? We have 1 online manual for this item!
Question posted by brandonstjohn on May 16th, 2014
Needle Issue
needle motion stopped while sewing. Needle will not go back up. Had to remove needle carefully from below bobbin area.The hand wheel will not turn at all. I removed bobbin And took face plate off to check area for blockage. The threading area under the face plate is not movable at all. Help!
Current Answers
Related Pfaff C1100 Pro Manual Pages
Owner's Manual - Page 2
....
5. Always unplug before checking and re-lamping. Keep ventilation openings of the sewing machine and foot control free from the electrical outlet when removing covers, lubricating, or when making any adjustments in the instruction manual. 11.Never drop or insert any other user servicing adjustments mentioned in the needle area, such as a wrong needle plate can cause the...
Owner's Manual - Page 3
...- Do not store anything on the needle while sewing. Do not use . If the problem persists, please consult your eye on the foot control. 4. A power failure occurs during use or store the machine near a space heater, iron, halogen lamp, or other parts to clean the machine. Replacing or removing the needle or any assemblies, the presser...
Owner's Manual - Page 6
... ...66 QUILTING ...67
Hand-look quilting stitch ...67 Decorative patchwork stitching...67 ATTACHING THE EDGE/ QUILTING GUIDE 68
DECORATIVE TECHNIQUES
CORDING...69 Single cording...69 Triple cording...69
FAGOTING...70 GATHERING ...71-72 SATIN STITCH SEWING ...73 SCALLOP STITCH ...74
Scallop hem...74 Scallop edging...74 SMOCKING ...75 TWIN NEEDLE SEWING ...76-77
DECORATIVE...
Owner's Manual - Page 7
Buttonhole Foot 8. Brush/seam ripper 19. Zipper Foot 4 3. Pack of needles 11. Soft canvas cover (Black)
6
INSTRUCTIONS ACCESSORIES
1. Rolled Hem Foot 7 5. Bobbin (3X) 12. Net 13. Gathering Foot 4. Three-groove Cording Foot 6. Screwdriver (L & S) 18. Fancy Stitch Foot 1A 7. Fancy Stitch Foot 2A 10. Spool cap – small (...
Owner's Manual - Page 8
PRINCIPAL PARTS OF THE MACHINE
Bobbin thread guide
Sewing speed control
Stitch chart Presser foot pressure dial Operation buttons
Face plate
Thread cutter Buttonhole lever Needle threader Needle plate Sewing table and accessory box
Drop feed lever
Spool pins
Retractable thread guide
Bobbin winder Bobbin winder switch and thread cutter
LCD screen LCD screen brightness control Function ...
Owner's Manual - Page 9
... maximum speed of the sewing speed control will allow the needle to stop the sewing machine. Note: The setting of the machine when using the foot control. The appliance must be used with the foot control C-9001 manufactured by CHIEN HUNG TAIWAN., LTD.
8
INSTRUCTIONS Turn on the sewing machine. Unplug the power cord when the machine is not in doubt...
Owner's Manual - Page 10
... the left. OPERATION BUTTONS
Needle position button Auto-lock button Reverse button Thread Snips
START/STOP button
START/STOP button Thread Snips
The machine will start running when the START/STOP button is pressed and will stop when pressed the second time. Use the sewing speed control to adjust the sewing speed. The sewing speed can be controlled by...
Owner's Manual - Page 12
... will raise or lower the needle.
When you press the button so that the arrow " " (on the LCD screen) will point upward and the needle will stop in the lowest position. OPERATION BUTTONS
Needle position button
Press the needle position button so that the arrow points downward " ", the machine will stop with the needle in the highest position.
Owner's Manual - Page 16
... is changed.
Mirror imaging the stitch appears on and the machine automatically reduces the width for twin needle sewing. Mirror imaged
Twin needle button
Stitches can be mirror imaged along a vertical axis by pressing the " " button, the LED light will turn on the LCD screen. Normal B - Press the button again to return to 2.0mm. Combine...
Owner's Manual - Page 25
WINDING THE BOBBIN
8.
Attention: Since this machine is full, and the bobbin winder switch returns to the left and bobbin winder button is pressed, the LCD screen will display the animation of the needle area
11
while winding the bobbin.
24
GETTING READY Remove the bobbin then cut the thread on the thread cutter.
Push the bobbin winder switch to the...
Owner's Manual - Page 28
Improper threading could result in the thread guide above the spool of thread.
2
27
GETTING READY Place thread in several sewing problems.
2
4
1
3 5
7
6 8
9 10
Before threading the machine, raise the needle to its highest point and raise the presser foot to release the tension discs.
1. Slide the spool of thread onto the spool pin
so...
Owner's Manual - Page 34
... replacing the needle !
REPLACING THE NEEDLE
Attention: Turn power switch to its highest position.
Securely tighten the needle clamp screw.
33
GETTING READY CUTTING THE THREAD
Press thread snips after finishing sewing and the machine will go. A.
With the flat side of the face plate and cut using the thread cutter. Raise the presser foot.
To check the needle, place...
Owner's Manual - Page 46
... PRESSER FOOT PRESSURE ADJUSTMENT
Presser foot pressure controls the amount of pressure placed on the top of the face plate, and can be used to adjust the presser foot pressure. For regular sewing of the machine has been preset and usually requires no particular adjustment.
The presser foot pressure dial is on the fabric...
Owner's Manual - Page 49
USEFUL SEWING TIPS
Sewing corners
3
1. Use the needle as a pivot and turn the fabric.
5. Raise the presser foot.
4. Lower the presser foot and resume sewing.
48
SEWING BASICS Stop the sewing machine when you reach a corner.
2. Lower the needle into the
5
fabric manually or by pressing the needle up/down button till
needle is in down position.
3.
Owner's Manual - Page 50
... the presser foot that should be sewn with a twin needle, refer to "Stitch Reference
Chart" beginning on page 39. 2. Determine the stitch that you wish to use .
* Refer to Stitch Chart on page 92. 3. Check that the correct presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select...
Owner's Manual - Page 53
...the guide to the right. Sew slowly, guiding the fabric carefully along the edge of the fabric. Place...Adjust the guide (b) by hand until the needle swings fully to sew blind hems. Always make a sewing test first.
1. Turn the fabric over. It should...the needle just barely catches the fold as illustrated with the wrong side facing up.
2. Attach the blindhem foot. Turn the handwheel toward you sew....
Owner's Manual - Page 57
... completed, the machine automatically sews reinforcement stitches, then stops. Note: If a shank is required, place a needle
6
or straight pin on top of the upper thread gently, and begin sewing. Position the fabric under the foot. For 4-hole buttons, sew the two holes towards the front. Hold the end of the button and sew.
56
STITCHES Remove the presser...
Owner's Manual - Page 59
... Note: Gently guide the fabric by hand. Position the fabric under the presser foot with the front end of the upper thread, start to sew any buttonhole stitch before the buttonhole lever... the center line on the buttonhole foot.
4
Note: When you start sewing. Before stopping, the machine will automatically sew a reinforcement stitch after the buttonhole is lowered, the LCD screen will show...
Owner's Manual - Page 78
... 2-B, other . Note: When sewing with a twin needle. The LCD screen will turn the handwheel to insure quality stitching.
7
77
DECORATIVE TECHNIQUES Select a stitch. Each time a different stitch is selected, touch the twin needle button for twin needle sewing by 2mm.
5
6. Two lines of the thread guide.
4
5. Note: Before sewing, always turn on, and the machine automatically reduces the...
Owner's Manual - Page 92
... 19
The sewing machine doesn't operate
2.The START/STOP button or foot control 2.Press the START/STOP button or the page 8/9
pedal was not pressed.
page 88
5.The machine is too heavy for the 3.Change stitch length. page 27
3.The needle is not plugged in the hook race.
4.Remove the upper thread and bobbin case, turn the handwheel backwards...
Similar Questions
Bobbin Or Bobbin Case Issues...i Guess
i bought a used creative vision 5.0....it has not sewn correctly since i took it out of the box 3 da...
i bought a used creative vision 5.0....it has not sewn correctly since i took it out of the box 3 da...
(Posted by jc5352 3 years ago)
What Size Bobbin Does The Pfaff C1100 Pro Take?
I have gone through the manual several times and can't locate the information. I have also searched ...
I have gone through the manual several times and can't locate the information. I have also searched ...
(Posted by mbbellardini 8 years ago)
Where To Find Pfaff Hobby 1132 Needles And Bobbins For Sale Online ?
Where to buy online Pfaff Hobby 1132 needles and bobbins
Where to buy online Pfaff Hobby 1132 needles and bobbins
(Posted by jgmeunier 8 years ago)
Pfaff C1100 Pro Sewing Machine Instruction
Can you please direct me to "easy" to understand instruction on how to "thread" my Pfaff C1100 Pro s...
Can you please direct me to "easy" to understand instruction on how to "thread" my Pfaff C1100 Pro s...
(Posted by magicfeathers55 10 years ago)
My Pfaff C1100 Is Clicking Continuously And Is Not Operational
Hello My sowing machine Pfaff C1100 was sowing away even after I removed my foot from the pedal. I ...
Hello My sowing machine Pfaff C1100 was sowing away even after I removed my foot from the pedal. I ...
(Posted by kasperflindt 11 years ago)