Panasonic AX200U Support Question
Panasonic AX200U Support Question
Find answers below for this question about Panasonic AX200U - LCD Projector - HD 720p.Need a Panasonic AX200U manual? We have 1 online manual for this item!
Question posted by wernerfrohn on November 5th, 2012
Hdmi Input Problems With Ax200u
All of a sudden my HDMI inputs on the AX200U stopped working. Theprojector works fine with component and composite inputs. Tried different cable, which works on flat screen. The cable or source are not the problem. It's the projector. Any idea if this can be fixed easiliy?
Current Answers
Answer #1: Posted by kcmjr on November 5th, 2012 6:37 PM
kcmjr
Member since:
May 5th, 2011 Points: 4,254,245
Member since:
May 5th, 2011 Points: 4,254,245
The HDMI is integrated into the circuit board. It could have a bad solder joint if the jack has been used a lot or subjected to being smacked. That would require a tech. You might be able to locate a replacement circuit board on eBay but what I would do is enlist the services of a local computer tech to look it over and give you an idea what will be needed.
Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.
Related Panasonic AX200U Manual Pages
Operating Instructions - Page 1
Operating Instructions
LCD Projector
Model No. PT-AX200U
Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0235
ENGLISH
Operating Instructions - Page 2
... Industries Alliance: http:// www.eiae.org
2 -
The lightning flash with your Panasonic LCD projector. For disposal or recycling information, please contact your product may be of sufficient magnitude ...of uninsulated "dangerous voltage" within an equilateral triangle is required. Model number: PT-AX200U
Serial number:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT...
Operating Instructions - Page 3
... of projector, you wish to discard this device must use optional RS-232C serial interface cable with Part...of the FCC Rules.
Declaration of Conformity
Model Number:
PT-AX200U
Trade Name:
Panasonic
Responsible party:
Panasonic Corporation of Panasonic ... is encouraged to try to correct the interference by turning the equipment off and on a circuit different from that interference ...
Operating Instructions - Page 4
... See "Switching the projector on/off the projector 20
Projecting an image 21 Selecting the input signal 21 Positioning the...Screen size and throw distance 14 Projection method 15 Front leg adjusters and throwing angle 15 Lens shift and positioning 16
Connections 18 Before connecting to the projector 18 Connecting to COMPONENT IN/VIDEO IN/S-VIDEO IN 18 Connecting to COMPUTER IN/HDMI...
Operating Instructions - Page 5
... 37
OPTION menu 38 INPUT GUIDE 38 OSD DESIGN 38 OSD POSITION 38 BACK COLOR 38 STARTUP LOGO 38 AUTO SEARCH 38 HDMI SIGNAL LEVEL 38 INSTALLATION ...38 SLEEP 39 ALTITUDE 39 LAMP POWER 39 LAMP RUNTIME 39 TEST PATTERN 39
Contents
Maintenance
TEMP and LAMP Indicators 40 Managing the indicated problems 40
Care and Replacement 41 Cleaning the projector...
Operating Instructions - Page 8
...projector. You could fall or the projector could result in places which are subject to sudden... could result in fire or problems with batteries inside may cause ...projector. ET-PKX100). Furthermore, all installation work is a good idea to preserve and maintain a clean environment.
If the batteries are constantly making efforts to clean the inside of the lamp or the other components...
Operating Instructions - Page 9
... as fixed points of the lens becomes dirty from shining onto the screen.
Optical components If you use the projector consecutively 6 hours every day, the optical components may need to be magnified and projected onto the screen. ENGLISH - 9 It is built with your LCD. The projector has a high pressure mercury lamp and that this may explode or...
Operating Instructions - Page 10
Remote control for PT-AX200U (x1) N2QAYB000194
AA batteries for remote control (x2)
Safety cable TTRA0140 Attachment screw (x1) Safety cable (x1)
Lens cover (x1) TKKL5372
Power cord for continental Europe (x1) K2CG3FR00001
* The protectors for enclosed products, such as a plug cover or foam cartons must ...
Operating Instructions - Page 11
...)
Display the main menu or return to the previous menu. (page 27)
Navigate through the input method. (page 26)
Remote control signal emitter Remote control signal. (page 22)
Turn the ...frequently used functions from the option for shortcut. (page 26)
Battery compartment 1. Preparation
About Your Projector
Remote control
POWER button While the MAIN POWER button is on, switch between stand-by mode ...
Operating Instructions - Page 12
... 27)
Air exhaust port Heated air comes out of this may cause damage or injury. • While the projector is on, switch between stand-by mode and project mode. (page 19)
Control panel
INPUT SELECT Switch to protect the lens.
12 -
NOTE:
• Do not cover the ventilation openings or place anything...
Operating Instructions - Page 13
HDMI IN Connect HDMI signal cables. Connecting terminals (page 18/page 46)
About Your Projector
S-VIDEO IN Connect a S-VIDEO signal cable. VIDEO IN Connect an RCA composite video cable. Compatible with the Kensington MicroSaver Security System. (page 50)
Air filter (page 41)
Lens cover attachment hole
Front leg adjusters Screw up/down to the
projector. ENGLISH - 13 Preparation
J Back...
Operating Instructions - Page 18
... HDMI cable is adapted to your HDMI device for proper performance. • A compatible cable is required for an HDMI 1 080p signal. • It is possible to connect with DVI devices via a HDMI/DVI conversion adapter, but some equipment may not project the
image properly or other problems could be connected. Getting Started
Connections
Before connecting to the projector...
Operating Instructions - Page 19
... The MAIN POWER button is switched off and unplug the power cord from the AC IN connector on the side of the projector match, then push the plug all the input devices are connected and turned off before connecting the power cord. • Do not force the connector as this may damage...
Operating Instructions - Page 21
... the required device.
2. Press the INPUT SELECT button to adjust the size of...on page 23.
2. Press the play button of the projector. See "TEST PATTERN" on the connected devices. Positioning... focus, you may need to select the required input method if needed. Adjust the focus and the projected...detected automatically.
Projecting an image
Selecting the input signal
1. Turn the focus ring and ...
Operating Instructions - Page 22
...obstacles between the remote control and the remote control signal receptor, the remote control may differ due to operate. To escape from the light-on mode.
Turning on the button backlight... CINEMA2
NATURAL
Display the FAVORITE LOAD menu. Q Facing to the projector
Ensure the remote control emitter is facing to the screen and press the required buttons to operate the remote control. See ...
Operating Instructions - Page 23
... the input method but also by pressing the ASPECT button. Q VIDEO/S-VIDEO/COMPONENT (YPBPR)
4:3
ZOOM2
16:9
ZOOM1
14:9
Q COMPUTER (RGB)
4:3
16:9
Q HDMI
JUST ...ratio
The aspect ratio will be cropped. See "ASPECT" on the screen as follows.
Basic Operation
ENGLISH - 23 NOTE:
• Some menu...again to cycle through the different aspect type as a still picture. Display the required sub-...
Operating Instructions - Page 26
... the projected image and you select an unplugged input method, the guidance will be changed in yellow.
COMPONENT IN
S-VIDEO IN
S-VIDEO IN
S-VIDEO signal from the equipment connected to HDMI 1 IN/HDMI IN 2. BLANK SLEEP FAVORITE LOAD LIGHT HARMONIZER AUTO SETUP HDMI 1 IN HDMI 2 IN COMPUTER IN COMPONENT IN
page 37 page 39 page 32 page...
Operating Instructions - Page 28
...DYNAMIC IRIS LIGHT HARMONIZER
ADVANCED MENU
FAVORITE SAVE FAVORITE LOAD FAVORITE EDIT SIGNAL MODE*1
*1. COMPUTER/COMPONENT/HDMI signals only
Options (Underlined is default setting)
NATURAL
NORMAL
DYNAMIC
CINEMA1 GAME
CINEMA2
VIVID CINEMA...5 options. NOTE:
• Some default settings vary by the selected input signal. • Sub-menu items vary according to display the sub-menu. Select...
Operating Instructions - Page 38
...; HDMI SIGNAL LEVEL is turned on /off the guidance.
The INPUT GUIDE will be displayed for when the projector is displayed when
starting up the projector. You can change the position where to cycle through the options.
See "Projection method" on page 28. OPTION menu
Remote control
Control panel
BACK COLOR
You can choose a screen...
Operating Instructions - Page 44
...input source may not be connected to a terminal properly. The input selection setting may be correct. The projector may not be tilted too much.
The input source which is not compatible with the projector... the screen. No electric supply is lit or flashes. TEMP indicator is at the correct distance from a computer does not appear.
The BLANK function may be a problem with ...
Similar Questions
A Problem With The Lcd Projector Panasonic Pt-f300ea
the problem is that :- -when the power is connected , power indication is red , We press the power b...
the problem is that :- -when the power is connected , power indication is red , We press the power b...
(Posted by mkz90 9 years ago)
Order Pt-lb90ntea Lcd Projector
Dear Sir, I’m Phuong. I work for UPVIET Co., Ltd, Vietnam. Now, I have demand of buying PT-LB90N...
Dear Sir, I’m Phuong. I work for UPVIET Co., Ltd, Vietnam. Now, I have demand of buying PT-LB90N...
(Posted by nguyenphuong 10 years ago)
Problem With Pt Lb2 Projector
I change the lamp recently and now, when I try to put power on, the three LED stay open few second a...
I change the lamp recently and now, when I try to put power on, the three LED stay open few second a...
(Posted by alexandrec 11 years ago)
A Panasonic Lcd Projector Model No Pt-lb51sea Regularly Indicate A Temp.
(Posted by lraviraj84 11 years ago)
Power Cord
The AC Power Cord that came with my projector has only two prong openings available to be plugged in...
The AC Power Cord that came with my projector has only two prong openings available to be plugged in...
(Posted by erschatzle 12 years ago)