Panasonic 1100W Support Question
Panasonic 1100W Support Question
Find answers below for this question about Panasonic 1100W - Sharp 1 CF Microwave.Need a Panasonic 1100W manual? We have 1 online manual for this item!
Question posted by richardcrowe on January 13th, 2013
What Is The Best Way To Warm Plates
The person who posted this question about this Panasonic product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Panasonic 1100W Manual Pages
Service Manual - Page 1
... Single Phase, 60Hz
1370W
1370W
1370W
1370W
1200W
1100W
1100W
1100W
*2450MHz *99min.99sec *20 "(518mm)(W)O 16 "(407mm)(D)O *14 "(375mm)(W)O 15 "(386mm)(D)O *26.5 lbs. (12.0kg) Output power:IEC705-88 Test Procedure
11"(301mm)(H) 8 "(225mm)(H)
Specifications subject to the last page. SIMMC 0001002C1
E1
Service Manual Microwave Oven
Specifications for APH :
MODELS NN-S560BF/WF...
Service Manual - Page 2
... Park 65th Infantry Ave. These parts are special components used in attempting to or loosening of hinges and latches. (5) Evidence of potential dangers in the microwave oven which are important for safety. CONTENTS
(Page)
(Page)
FEATURE CHART 3 DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE 13
CONTROL PANEL 3 COMPONENT TEST PROCEDURE 16
OPERATION AND DIGITAL...
Service Manual - Page 3
... very hot in ordinary microwave ovens.
2. 3. High voltage may remain in circuit. It is very dangerous to adjust without proper test equipment. INVERTER POWER SUPPLY DIAGRAM
H.V INVERTER(U) * 3
INVERTER SUPPORT BRACKET OF ORIFICE
LEAD WIRE
HEAT SINK (RECTIFIER BRIDGE)
CHOKE COIL CURRENT
TRANSFORMER SAND BAR RESISTOR
HIGH VOLTAGE TRANSFORMER
GROUNDING
PLATE * 4
PCB
DO NOT...
Service Manual - Page 5
... your instructions. If door is opened or STOP/RESET Pad is pressed once during
oven operation, START Pad must again be pressed to begin functioning.
During cooking: One ... (13) Cooking Guide (14) Auto Cook Pad (15) Serving/Weight Pad (16) Start Pad
One tap allows oven to restart oven.
(17) Stop/Reset Pad
Before cooking: One tap clears your
instructions and time of day or colon appears on the ...
Service Manual - Page 6
If you pluge the power supply cord into the wall outlet, microwave oven automatically enter into the state of lb / oz. To Set Clock
OPERATION.... 5 sec.= 5
. 5
4. Time of day or colon if set appears in the display.
2. When cooking time has elapsed, oven beeps 5 times and shuts off . Press Auto Cook pad.
Place a water load in the display.
5.
Cooking begins as time counts ...
Service Manual - Page 10
...This drives the High voltage transformer to increase up to 2,000V AC and approximately 3V AC by means of the microwave oven is as the H.V. HIGH
P10
P9
P8
MEDIUM-HIGH P7
MEDIUM
P6
P5
P4
MEDIUM-LOW P3
P2
P1
DEFROST... immediately. 2. Then the half-wave doubler voltage rectifier circuit, consisting of the microwave oven from the current transformer built into the inverter ciruit. 6.
Service Manual - Page 11
...food cooks, a certain amount of time it takes the microwave oven to switch to be prepared in the microwave oven using the formula below make sure this 10 second is successful...X 0.1 =160 sec. Sensor Cooking (NN-S560BFAPH/CPH NNS560WFAPH/CPH)
Auto sensor cooking is a quick and easy way to cook the food. In Auto Sensor Cooking, a carefully designed instrument, called T2 time, can be 2 minutes...
Service Manual - Page 12
... Voltage Inverter Power Supply circuit board must replace Primary latch switch and short switch. Be sure to have a proper chassis ground by the grounding plate and screws.
The microwave oven is also energized with an insulated handle screwdriver to discharge. Inverter Warnings NEW H.V. The aluminum heat sink is designed to be taken during...
Service Manual - Page 13
... components have potentials above 250V while the
appliance is operated with the door hinges or magnetron
fixed incorrectly, the microwave leakage can reach more than 5mW/cm2. When the appliance is operating..
*h Magnetron *h High voltage transformer (...are not properly tightened. (B) Make sure that the screws of the
oven, etc. Microwaves might leak if screws are neither loose nor missing.
Service Manual - Page 14
... attaching orifice assembly. (C) Remove orifice assembly/Inverter power supply (U) from oven assembly. (Refer page 15) (D) Remove fan blade from DPC contacts, remove the defective transformer/power relays and install new transformer/relays making sure there is attached to prevent microwave leakage.
NOTE: 1. SCREW
- 13 - DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE
1. Resolder all terminal...
Service Manual - Page 15
...so that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected to the base using a flat blade screwdriver. (B) Separate door E from tabs on sensor mounting plate and air guide....Note: The door
cannot be removed if the opening angle of the door, reassemble, install, and perform microwave leakage test.
6. DOOR CCREEN B DOOR A DOOR KEY DOOR KEY SPRING
DOOR E
BASE
DOOR C
MOTOR...
Service Manual - Page 16
Disconnect all wires to correct location and redress turntable wires.
- 15 - Detach turntable wires
from the
oven. Remove 2 screws holding inverter to leave the grounding plate in its place. 2. Push Inverter Assembly until locking tabs are locked. 12. Take off outer panel.
6. Slide four locking of oriffice at the bottom of a ...
Service Manual - Page 19
... to the door hook is necessary.
(B) When mounting the door hook assembly to the oven assembly.
(C) Reconnect the short switch and check the continuity of the monitor circuit and ...all latch switches again by pulling the door assembly. Measurement of microwave output
The output power of the magnetron can be determined by moving it for exactly... the center of glass cook plate.
Service Manual - Page 20
... the radiation leakage be taken. This requirement must be more than 2mW/cm2 (1mW/cm 2for Canada). (5) Leakage for a fully assembled oven [Before the latch switch (primary) is graduated to a microwave oven, a leakage reading must be recorded on the repair ticket even if it following the manufacturer's recommended test procedure to assure correct...
Service Manual - Page 21
... may damage this panel to component test procedure and replace if it is blown.
3. Oven is defective. No display and no operation at all operate the microwave oven following the correct operating procedures in with the AC plug removed. Oven does not accept key input(Program)
4. Timer starts count down but timer does not...
Service Manual - Page 23
...H98, or H99 appears in display window a short time after start key is pressed and no microwave oscillation.
Inverter (U) (SEE NOTE)
NOTE: After check, unplug unit to reset to normal ...circuit is produced by pressing Clock , Time , Start , Power Level .
Alternate way to troubleshoot oven with AC Ampere meter used for operation. This section explains failure codes of inverter ...
Service Manual - Page 24
...PF1). (2) Insert the removed jumper wire (PF1) to Digital Programmer Circuit
SYMPTOM No display when oven is detected, replace the defective parts. NOTE:* At the time of these repairs, make visual ...though the program has been set and the start pad is tapped
No microwave oscillation at any abnormal condition is first plugged in window and oven stops operation. STEP 1 1 1 2
1
2 1 1
CHECK ...
Service Manual - Page 26
...PLATE NAME PLATE NAME PLATE NAME PLATE NAME PLATE BASE
Pcs/ set
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks
******APH ******CPH S560BFAPH S560WFAPH S560BFCPH S560WFCPH S550BFAPH S550WFAPH S540BFAPH S540WFAPH S540BFCPH S540WFCPH L530BFAPH L530WFAPH L530WFCPH L520WFCPH S510WFCPH
4
F10084T00AP
RUBBER FOOT
5
F110D4T00BAP
CABINET BODY (U)
5
F110D4T00HAP
CABINET BODY (U)
6
F201A4T00AP
OVEN...
Service Manual - Page 27
...1
1
S560*FAPH, S550*FAPH
1
S560*FCPH
1
S540*FAPH, L530*FAPH
1
S540*FCPG, L530WFCPH,L520WFCPH,S510WFCPH
B62308250AP B62314000AP F61844T00AP B63264080AP F900C9660AP F900C9660CP
FUSE FUSE HOLDER GROUNDING PLATE TURNTABLE MOTOR AC CORD W/PLUG AC CORD W/PLUG
1
18A/120V,60Hz
1
******APH
1
1
1
******APH
1
******CPH
A692Y4T00CP XTWANE+10RU XST4+5VS XYD4+EE12F XTCA4+12AFK
NOISE FILTER...
Service Manual - Page 36
Part name & Description Pcs/ Set
Remarks
F00074T20BRP NAME PLATE
1 NN-S540BF
F00074T20HRP NAME PLATE
1 NN-S540WF
F00074T70BRP NAME PLATE
1 NN-540BF
F00074T70HRP NAME PLATE
1 NN-540WF
F603L4T70RP D.P.CIRCUIT
1 NN-S540BF/WF, NN-540BF/WF
F603Y4T20BAP MEMBRANE SWITCH(U)
1 NN-S540BF
F603Y4T20HAP MEMBRANE SWITCH(U)
1 NN-S540WF
F603Y4T70BRP MEMBRANE SWITCH(U)
1 NN-540BF
...
Similar Questions
Panasonic Nn-h765bf Microwave Purchased 2008 Troubleshooting.
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
(Posted by Kamathn 11 years ago)
My Connectionless Steamer Microwave Oven Ne-2180 Does Not Work Fuses Replaced
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
(Posted by sbenson99 11 years ago)
Where Can I Find The Glass Plate?
(Posted by Hespinoza1 11 years ago)