Oreck XL3640HH Support Question
Oreck XL3640HH Support Question
Find answers below for this question about Oreck XL3640HH.Need a Oreck XL3640HH manual? We have 1 online manual for this item!
Question posted by arthur376 on September 14th, 2012
Position Of Switch
is the O on top and I on the bottom of handle?
Current Answers
Related Oreck XL3640HH Manual Pages
Owners Guide - Page 1
... • Warranty • Operating Instructions • Trouble Diagnosis • Accessories
75646-02 REV C
S I M P LY
A M A Z I N G®
VISIT ONE OF OUR OVER 450 STORE LOCATIONS
USER'S GUIDE
XL3640HH USA: 1-800-989-3535
CANADA: 1-888-676-7325 COMMERCIAL: 1-800-242-1378 www.oreck.com www.oreckcommercial.com
VISIT ONE OHF OIGURHOSVEPR EED UPRIGHT...
Owners Guide - Page 3
...service in the U.S.A., present this appliance. • Use caution when vacuuming over cord. • Do not unplug by cord, use in areas...unplug, grasp the plug, not the cord. • Do not handle plug or appliance with this slip to replace the obsolete outlet.
...surfaces. • Do not run while in the upright and locked
position. • Do not let the unit run appliance over area rug...
Owners Guide - Page 5
...This will cause damage to use . An extra belt is one stationary position for the effective operation of your ORECK vacuum cleaner. A little preventative maintenance will void the warranty.
NOTE: Do...
The vacuum cleaner motor bearings are not the same. Safety-Lighted Power Switch
fig. 4 When the unit is plugged in the manual for vacuum use on power head and lean handle back ...
Owners Guide - Page 6
...surfaces and polished floor finishes. Change it more often if it is used in the upright and locked position.
fig. 9 Gently pull bag cardboard collar upward out of the belt on the brush roll pulley...
opposite end of the bag dock.
fig. 20 Rotate both bearing assemblies at ends of your vacuum by removing two (2) screws in place against fan housing opening. When rotating bearings, make sure...
Similar Questions
My Halo Will Not Pick Up Upright Position. Why?
Hello, My husband brought home a Halo Vacuum Cleaner last year or a little over. Shortly after, it s...
Hello, My husband brought home a Halo Vacuum Cleaner last year or a little over. Shortly after, it s...
(Posted by olddude1969 9 years ago)
Replacing The On/off Switch.
My Oreck fell and the switch was pushed into the handle. I can not see how the switch stays in betwe...
My Oreck fell and the switch was pushed into the handle. I can not see how the switch stays in betwe...
(Posted by barryrk 10 years ago)
Xl3640hh
I have an xl3640hh and if I want to buy a new one How much would it cost me? thank you.
I have an xl3640hh and if I want to buy a new one How much would it cost me? thank you.
(Posted by oneilfj 11 years ago)
Baseplate Foe Xl3640hh
was the base plate made improved over the years. my base plate doesn't have 2 extea wheels on it and...
was the base plate made improved over the years. my base plate doesn't have 2 extea wheels on it and...
(Posted by oneilfj 11 years ago)
Looking For A Wiring Diagram For The Off/on Switch For Oreck U3700hh
I am replacing the off/on switch part # 294927 on the oreck U3700hh. Have disassembled the handle an...
I am replacing the off/on switch part # 294927 on the oreck U3700hh. Have disassembled the handle an...
(Posted by srpctm 12 years ago)