Oreck XL2400RS Support Question
Oreck XL2400RS Support Question
Find answers below for this question about Oreck XL2400RS.Need a Oreck XL2400RS manual? We have 1 online manual for this item!
Question posted by rancherbobby on June 30th, 2012
Motor Sounds Like It Is Laboring.
COULD THIS BE DUE TO BAB BRUSHES ON THE MOTOR
Current Answers
Related Oreck XL2400RS Manual Pages
Owners Guide - Page 1
...-3535 CANADA: 1-888-676-7325 COMMERCIAL: 1-800-242-1378
USER'S GUIDE www.oreck.com
www.oreckcommercial.com VISIT ONE OF OUR OVER 450 STORE LOCATIONS
XL2400RS
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Owners Guide - Page 2
...8226; Do not leave appliance unattended when plugged in this appliance. • Use caution when vacuuming over cord. • Do not unplug by cord, use and before unplugging. • Use...Tab page 4
Operating Instructions page 5
How to Replace a Worn Belt, To Adjust or Replace Brush page 6
Stuffing or Blockage page 7
Troubleshooting Guide page 8
Polarized Plug Notice This product is ...
Owners Guide - Page 3
...warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes, edge brushes, drive belts, bulbs, disposable bags and other rights which can be oiled.... normal domestic use only. Oreck's limited warranty is a product of precise engineering.
Save your vacuum,
the parts have problems with the sale of this product. Dust Bag, 8 Pack Regular
...
Owners Guide - Page 4
... shaped part on connector.
Using An Oreck Fresh Air® Tab
Your ORECK XL vacuum cleaner has a special FRESH AIR® tab pocket. Slide upper handle section over matching... section of base when ready to release lock for any one stationary position for vacuum use.
This light-colored pocket is in the upright and locked position. 1
2
Upper
3
4
...
Owners Guide - Page 5
... on wet or damp surfaces is not covered under things, and it will guide you vacuum. See instructions in performing basic care and maintenance.
The instructions in this manual will cause the revolving brush to the motor and brush bearings. The following are a few simple suggestions regarding its class. DO NOT run while in...
Owners Guide - Page 6
... screw. The one marked "NEW" has a notch. Remove the belt from the storage channel. Place the opposite end of brush.
To determine if the brush is overhanging the end of power head. Loop the new belt over the motor drive shaft. Replace the door by removing the hold down screw located on the...
Owners Guide - Page 7
Remove debris with a coat hanger.
3. Vacuum will cause stuffing when the cleaner is not at the mouth of tube. Make sure O-ring is ...fuzz and loose cuttings in the area where the dust bag connects to approximately 2" from electrical outlet before servicing. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up or balloon open,...
Owners Guide - Page 8
...Check electrical source-fuse or circuit breaker. Nozzle or intake Clear obstruction. stretched.
Revolving brush is firmly plugged into wall outlet.
CALL CUSTOMER SERVICE HOT LINE US:1-800-989-3535
...WILL NOT RUN
Not plugged in the proper location? • Does the brush turn freely?
Brush is full. Clear obstruction.
Return to have your model and serial number from...
Similar Questions
El Motor Suena Fuerte Al Encender
lo entiendo y el motor suena muy fuerte que es el problema
lo entiendo y el motor suena muy fuerte que es el problema
(Posted by noelosvaldo13 3 years ago)
Watts
I just moved to Germany. I have an Oreck XL2400RS. I need to buy a transformer to use it because ele...
I just moved to Germany. I have an Oreck XL2400RS. I need to buy a transformer to use it because ele...
(Posted by jefortunato 11 years ago)
Oreck Vacuum Model #xl2800h2 Remove+ Replace Motor Where Do The Plugin Wires Go?
(Posted by PKELL911 11 years ago)
Where Can I Get New Brushes For The Motor Of The U3700hha?
(Posted by daparkers 11 years ago)
Whats Wrong With It?
my 0reck xl21- 700 ecb motor sounds like its dying... how do i fix it? also how do i find out how ol...
my 0reck xl21- 700 ecb motor sounds like its dying... how do i fix it? also how do i find out how ol...
(Posted by mybigtoerocks 12 years ago)