Oreck Graphite Support Question
Oreck Graphite Support Question
Find answers below for this question about Oreck Graphite.Need a Oreck Graphite manual? We have 1 online manual for this item!
Question posted by Cromanelli8 on November 27th, 2012
How Do I Remove The Bottom Plate Of The Graohite Oreck? I Must Replace The Belt.
The person who posted this question about this Oreck product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Oreck Graphite Manual Pages
User Guide - Page 1
Read all instructions carefully, and keep for future reference. Graphite™
User's Guide
U4305H2BS
Important!
User Guide - Page 2
...anything that stays in the bag and doesn't blow back into the air. The U4305H2BS Graphite features a 6-year limited warranty and the HEPA Filtration Odour Fighting Bag captures dust &...• Do not run while in any one stationary position for purchasing the Oreck U4305H2BS Graphite series upright vacuum cleaner.
Use only manufacturer's recommended attachments. • Do not use with ...
User Guide - Page 3
... 3 Parts List 3 Assembling the Handle Tube 4 Operating the Vacuum 4 Replacing the HEPA Filtration Odour Fighting Bag 4 Simple Operation Tips and Vacuum Care 5
General Information 5 HEPA Filtration Odour Fighting Bags 5 The Belt 5 Lubrication 6
Maintenance 6 Replacing Worn Belt 6 Adjusting or Replacing Brushroll 7 Replacing Edge Brush 7 Stuffing or Blockage 8
Troubleshooting 8 Parts...
User Guide - Page 4
... while in the upright and locked position.
Connector
1
Assembly
2.1
3
Operating the Vacuum
Make sure the HEPA Filtration Odour Fighting Bag is in bottom hole of Connector Assembly...Handle Tube
1 Before assembling appliance, remove two screws from the Connector Assembly. Hold tab of the Harness (21 on connector.
5
4
5
Replacing the HEPA Filtration Odour Fighting Bag
WARNING...
User Guide - Page 5
... things, and it is installed properly. Operation
ENGLISH
Simple Operation Tips and Vacuum Care
This new ORECK Upright is full, REPLACE IT. 3.
DO NOT FILL ABOVE THE LINE INDICATED ON THE DISPOSABLE INNER BAG. If the belt becomes stretched or cut, it must be
removed from the floor before you in the baseplate of your...
User Guide - Page 6
... Replace the phillips head screw and tighten.
11
12
13
14
15
6 General Information
ENGLISH
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed. Do not operate the unit while in operation. Do not let the unit run while in the outer bag, vacuum it or shake it away. 14 Remove the belt...
User Guide - Page 7
..., remove the belt and brushroll from electrical outlet before servicing.
When rotating, both bearing assembly settings arethe same and face up , remove the screws attaching the base plate (16) then remove the screw located in the housing. 18 Note:The bearing assembly setting market "OLD" has no ribs on the top of each edge brush. Replace...
User Guide - Page 8
... Odour Fighting Bag".
• Nozzle or intake pivot clogged.
• Clear obstruction.
• Belt is broken or stretched. • Replace belt.
• Brush is first used on them. Replace and tighten collar until the tube is seated.
Replace tube by an
Oreck Approved Service Centre.
Unhook bag spring, releasing bottom of bag. 25 Twist lower collar...
User Guide - Page 9
... inability to you purchase this limited warranty.
This limited warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes, edge brushes, drive belts, brushes, bulbs, disposable bags and other than Oreck or a participating Oreck Approved Service Centre.
This limited warranty does not apply to normal wear unless they...
User Guide - Page 10
All rights reserved. ©2011 Oreck Holdings, LLC. All word marks, logos product configurations and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. 76140-01 REV A 06/15 ECN # R-10492 UK Edition
Similar Questions
Wiring
there are black,white ,and green wires in the power cord -- what is the green one for ?
there are black,white ,and green wires in the power cord -- what is the green one for ?
(Posted by gearlh 1 year ago)
Is The Oreck Graphite Different From The Oreck Insight Xl
(Posted by Anonymous-132532 10 years ago)
Oreck Vacuum Model #xl2800h2 Remove+ Replace Motor Where Do The Plugin Wires Go?
(Posted by PKELL911 11 years ago)
Brush Belt Replacement
I am looking for belt for MODEL UV-ST-3290. THANK YOU
I am looking for belt for MODEL UV-ST-3290. THANK YOU
(Posted by bbentz44 11 years ago)