Miele Crystal G 5285 SCVi Support Question
Miele Crystal G 5285 SCVi Support Question
Find answers below for this question about Miele Crystal G 5285 SCVi.Need a Miele Crystal G 5285 SCVi manual? We have 2 online manuals for this item!
Question posted by rtaylor73914 on January 16th, 2017
F 14 Technical Fault
What can be done when the dishwasher stops and all lights blink and the Fault is F14?
Current Answers
Answer #1: Posted by BusterDoogen on January 16th, 2017 7:47 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,447
Member since:
October 30th, 2011 Points: 28,565,447
Go here for a possible solution.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Miele Crystal G 5285 SCVi Manual Pages
Operating and Installation manual - Page 1
US, CA
M.-Nr. 09 510 220 en - Operating Instructions
Dishwasher G 5280 G 5285
To prevent accidents and appliance damage read these instructions before installation or use.
Operating and Installation manual - Page 2
... the water hardness 12 Filling the salt container 13 Salt indicator 14
Deactivating refill indicators 15 Rinse aid 16 Adding rinse aid 16 Rinse aid indicator 17 Setting the rinse aid dosage 18 Loading the dishwasher 19 Items not recommended for dishwashing 20 Typical load for 10 place settings with cutlery tray 21...
Operating and Installation manual - Page 3
... options 37 Turbo 37 Delay start 38 Buzzer 39 Optimize Standby 40 Factory defaults 41 Frequently Asked Questions 42 Technical faults 42 Faults in the water intake or water drain 43 General problems with the dishwasher 44 Sounds 45 Poor cleaning results 46 After sales service 49 User Maintenance Instructions 51 Cleaning and Care...
Operating and Installation manual - Page 5
... surface, oven or any plastic wrappings,
bags, etc. IMPORTANT SAFETY INSTRUCTIONS
Installation
~ The dishwasher must be installed
and connected in
a non-stationary location (e.g. Unplug the machine and contact Miele Technical Service Department.
~ Ensure that the cabinet opening for the dishwasher provides ample space for the plug and cord. This hose contains electrical components...
Operating and Installation manual - Page 11
...gal]). In areas where the water hardness fluctuates (e.
The water hardness factory setting is a fault, it will be programmed to correspond to the higher value (in this information in your...- Before using for the first time
Water hardness
To achieve good cleaning results, the dishwasher needs soft water.
Your local water authority will help the service technician to know the...
Operating and Installation manual - Page 12
... the Turbo button twice. If it off .
°d
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-50...53-63 64-73
Value to turn the dishwasher off .
^ Hold down for at a short interval. The Turbo indicator light flashes 2 times at least 4 more seconds until the lower right program indicator lights up one level. The time display shows the...
Operating and Installation manual - Page 14
... container lid.
Screw the lid on , refill the salt container.
Water does not have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal).
,Immediately run the Express program without ... function) to be filled with salt.
Salt indicator
^ When the Salt indicator comes on firmly.
14 The salt container holds approx. 4.4 lbs (2 kg) of salt, depending on the type of ...
Operating and Installation manual - Page 20
... should only be rubbed off with color painted over time
- Cast iron pots and pans
* depending on model
If unsure whether your china and crystal are dishwasher safe. When purchasing new dishes, glasses and cutlery, make sure they are not heat resistant
- Silverware previously cleaned with a silver polish may be damp or...
Operating and Installation manual - Page 30
... dosage. When using the "China & Crystal" program (depending on model) reduce the amount of detergent used to at least ½ of detergent. Avoid inhaling or swallowing dishwasher detergent. There could still be detergent residues in the dishwasher. Keep children away from the dishwasher when the door is open.
Dishwasher cleaning products are available from MIele...
Operating and Installation manual - Page 33
...dishware with
the ability to adjust energy and
water consumption based on food, and
heavily soiled dishware, use 50% detergent recommended. X
X
China & Crystal
For temperature sensitive glassware and lightly soiled dishware, use
120% detergent
recommended. X
X
X
X
Rinse & Hold
To rinse dishes when a
X
complete program is not
needed. X
X
X
X
Normal
Program for completely
as...
Operating and Installation manual - Page 34
... off and only the K indicator light flashes slowly.
^ Press the K button if you can deactivate the refill messages and let the dishwasher go into Standby mode (see "Additional options Optimize Standby"). It depends on . If Salt and/or Rinse aid or a fault is not turned off .
34 However, fault messages cannot be turned off...
Operating and Installation manual - Page 39
...is immediately saved.
^ Press the K button to turn the dishwasher on
-
"p 1": buzzer is activated by default. The Turbo indicator light shows 4 short flashes in intervals without pausing. The setting is...buzzer at least four seconds until the lower right program indicator lights up.
Keep the Program button pressed for a fault cannot be turned off so that it does not come on...
Operating and Installation manual - Page 40
... the program.
If it will turn off completely. "p 0": Optimize Standby is off .
40 The Turbo indicator light shows 8 short flashes in higher energy consumption. If Salt and/or Rinse aid or a fault is displayed, the dishwasher will switch to Standby mode to change the setting. Additional options
Optimize Standby
A few minutes after the...
Operating and Installation manual - Page 42
... closed . After a few seconds: - Close the door.
Technical faults
Problem
The dishwasher will not start. Possible fault
The door is reports a fault.
The dishwasher stops during a program.
The circuit breaker has tripped. All the indicator lights of the program selection flash when the door is a technical fault. - The time display shows fault FXX. There may run even The waterproof...
Operating and Installation manual - Page 43
... care").
- The dishwasher
has stopped. door is open . The time display
shows fault FXX. Open the water supply all the way.
Open the water supply all the way.
-
Fault F11: Water drainage fault. Clean the triple filter (see "User maintenance instructions").
- The Intake/Drain indicator light flashes when the
Fault F12/F13: Water intake fault. The water pressure...
Operating and Installation manual - Page 44
... triple filter (see "User maintenance instructions").
Press the K button to turn off . There is normal. Frequently Asked Questions
General problems with the dishwasher
Problem
Possible fault
Solution
The indicator lights and the time display are wet after a short time. Press the K button to save energy (Standby). The dispenser was wet when detergent was...
Operating and Installation manual - Page 45
... a rattling noise in the wash cabinet
There is a knocking noise in the water line
Possible fault
Solution
The spray arm is hitting an Interrupt the program,
item in the drain pump.
This has no effect on the dishwasher.
rearrange loose pieces. rearrange items blocking
the spray arms.
Items are not secure in...
Operating and Installation manual - Page 46
dishwasher".
change the detergent.
The spray arm jets might be wiped off. The non-return valve is clogged or not correctly inserted. Wash the non-return valve (see "Rinse aid").
46 streaks.
Frequently Asked Questions
Poor cleaning results
Problem
Possible fault
Solution
The dishes are blocked. Select a more detergent, or
dispensed.
The triple...
Operating and Installation manual - Page 48
...it making sure it not screwed on correctly.
48 Glasses are dull and Glasses are not dishwasher There is
Only use dishwasher safe
cannot be the cause. brown or blue
discoloration;
Use more detergent (see "Detergent...corrosion resistant. discolored; Frequently Asked Questions
Problem
Possible fault
Solution
Glasses have not been
the selected program was run after refilling salt.
Operating and Installation manual - Page 49
...the event of a fault which you cannot correct... MieleCare Extended Service Contracts, please contact your machine controls via the indicator light marked PC. Please note that your appliance investment is to prevent unauthorized....
PC Update
The Program Correction (PC) allows a technician to update the dishwasher to them, you the assurance of knowing that unless expressly approved in the ...
Similar Questions
How To I Restart The Dishwasher If I Open The Door During A Cycle?
How to I restart the dishwasher if I open the door during a cycle?The dishwasher does not restart - ...
How to I restart the dishwasher if I open the door during a cycle?The dishwasher does not restart - ...
(Posted by ymkinley 2 years ago)
Dishwasher Salt In Miele G 4225?
Can you add dishwasher salt to the Miele G 4225 dishwasher, and if so, how and in what quantities? T...
Can you add dishwasher salt to the Miele G 4225 dishwasher, and if so, how and in what quantities? T...
(Posted by jburbidge 5 years ago)
Our Dishwasher Won't Turn On. We Checked The House And The Fuses Are Fine. The D
the door lock also won't engage
the door lock also won't engage
(Posted by cdskipper 6 years ago)
What Is Fault 51
where can I find fault 51 and how to fix that fault
where can I find fault 51 and how to fix that fault
(Posted by maintenanceplusllc 6 years ago)
Dishwasher Madel Name Definition
What does the SC refer to in the model number G4225SC?
What does the SC refer to in the model number G4225SC?
(Posted by dwightdean 10 years ago)