Question posted by lilkas4 on February 6th, 2011
Maytag Precision Touch Control 500 Bake Oven Doesn't Work But Broiler Does.
Glow plug works when broiler is on but glowplug does not light when oven is put on...panel shows 100 and does not get hot. It is a maytag gas model number mgr5755qdw. How does the glowpug and ignitor work for broiler and not the oven.?
Current Answers
Answer #1: Posted by lilkas4 on February 12th, 2011 4:58 PM
The rangehas two separate ignitors. One for the broiler and one under the plate at the bottom of the range for the bake. You have to take the bottom plate off to reveal this ignitor.There are two screws in the back of the oven holding this plate in. The ignitor is held in by two screws and plugs in from behind the oven. I took a small metal plate off the back of the oven which revealed where it was plugged in. I found that the ignitor was bad and order one from AppliancePartsPro.com The model number was wpl 74008064. It was only $39.95 plus tax..Not bad when everyone else wants about $60.00 for the same part. I got in two days installed it and my oven is back to backing again.
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Locking the controls and oven door - Wall oven
...°F (204°C) or above. To lock: Press and hold the Cancel and Cook & To unlock: Press and hold the Cancel and Cook & Baking - If the oven is currently in wall oven. Wall oven Using the Control and Oven Door locking features on a built-in use . -
Setting the clock - wall oven and Gemini® range
... seconds; The display will not operate. Press the appropriate number pads to set the clock on a built-in the display. NOTE: When electrical power is showing, press the Clock pad. Clock time cannot be blank and the oven light will be changed when the oven has been programmed for Delay Cook or Clean or Cook... -
Timer settings - Wall oven
...time, one minute (00:01) up to clear the display. The timer does not control the oven. It only controls a beeper. Press Timer pad again or wait four seconds. The colon stops flashing...in wall ovens. Press the Timer pad to 99 hours and 59 seconds (99:59). The timer can also be displayed. Baking - Or Using the timer on the number pad. Oven Sabbath Mode - Oven Error ...
Similar Questions
The Baking Temperatures Are Not Working Only 440 Degrees On Up
how do I reset the control panel? The temperatures go to 440 degrees on up. No other buttons work?
how do I reset the control panel? The temperatures go to 440 degrees on up. No other buttons work?
(Posted by mrome1972 7 years ago)
Range Baking Oven Not Functioning
When push the bake button on the control panel, it says "Feature not available"
When push the bake button on the control panel, it says "Feature not available"
(Posted by xisunca 8 years ago)
Maytag Precision Touch 850 Series Bottom Oven Will Not Heat
(Posted by brijt 9 years ago)
Temperature Control Of Upper Oven
Temperature of upper oven, as mesured with a therometer is running 25 degrees higher than the settin...
Temperature of upper oven, as mesured with a therometer is running 25 degrees higher than the settin...
(Posted by edjasper 12 years ago)
Touch Controls Not Working
Model: MGR4451BDB Recently the "More" button quit working not allowing to increase oven temp. All o...
Model: MGR4451BDB Recently the "More" button quit working not allowing to increase oven temp. All o...
(Posted by radiation0512 12 years ago)