Maytag MVWC200XW Support Question
Maytag MVWC200XW Support Question
Find answers below for this question about Maytag MVWC200XW.Need a Maytag MVWC200XW manual? We have 3 online manuals for this item!
Question posted by Lorraindemaio15 on July 24th, 2013
Will Not Start No Power Power Is At Receptacle
tried everything unplugged it and waited no results
Current Answers
Related Maytag MVWC200XW Manual Pages
Installation Instructions - Page 2
...Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
...numbers on back page of your washer in the top of your Use and Care Guide.
INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before starting installation. Install your Use and...
Installation Instructions - Page 3
...store, or operate washer where it will need a sump pump system. n Hot and cold water faucets located within 4 ft (1.2 m) of
power cord on washer, and water pressure of washer.
Minimum siphon ...which are required. install no more space for installation with maximum slope of laundry tub must support washer's total weight (with beaded tie strap.
3
n A grounded electrical ...
Installation Instructions - Page 4
...in accordance with a power supply cord having a 3 prong grounding plug. n Check with the sound shield to have a fuse in the neutral or ground circuit.
48" (1.2 m)
Move washer to a gas pipe.... by a qualified electrician. If your washer includes a sound shield, please refer to the instructions included with a qualified electrician if you start: remove shipping materials It is necessary ...
Installation Instructions - Page 5
... NOTE: Keep tray in Step 7. Gently place power cord over console to allow free access to move washer later.
4.
You may need to back of washer.
4.5" (113 mm)
Place hose into standpipe or...parts with clamp. Attach drain hose to step 6.
For a laundry tub or standpipe drain, go to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from rear panel...
Installation Instructions - Page 6
...result. Screw coupling by hand until it is snug.
It will cross over each other when attached correctly. NOTE: Both hoses must use a Y-adapter (not provided).
8. Connect inlet hoses to washer... through hoses into a laundry tub, drainpipe, or bucket to water faucets
Run water for leaks. Check for leaks
Turn on washer.
Use pliers to faucets or washer. Do not use tape...
Installation Instructions - Page 7
... beaded tie strap.
Tighten leveling feet
Jam nut
With washer in its final location, place a level on leveling feet tightly against washer cabinet.
HELPFUL TIP: You may want to reduce excess noise and vibration.
13. If washer is level, skip to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with wooden...
Installation Instructions - Page 8
... are now installed.
q Remove protective film from back of /recycle all packaging materials. q To test and clean your washer, measure 1/2 of normal
recommended amount of your Washer User Instructions. Select any tape
remaining on . Start washer and allow to see what was skipped. q Check for leaks around faucets and inlet hoses.
q Check that all...
Owners Manual - Page 2
WASHER SAFETY
2
Owners Manual - Page 3
... distribution.
5 START/PAUSE/UNLOCK BUTTON Press to unlock the lid. It ensures that are available on all features and options are different from traditional washers.
You may take several minutes before locking again. Small will be set to "YES" if using fabric softener during a cycle. Select a wash temperature based on your laundry load...
Owners Manual - Page 4
...Heavy
Hot Warm Cool Cold
High Use this cycle for best results.
Combines a rinse and high speed spin for proper water ...washer spins the load at high speed.
This may take several minutes if the load was spinning at increasing speeds for loads requiring an additional rinse cycle or to complete a load after a power failure. Press START/Pause/ Unlock again to open the lid, press START...
Owners Manual - Page 5
...instructions to avoid damage to use.
5 Add a measured amount of detergent to your laundry
2.
Synthetics, knits, and corduroy fabrics will pick up lint from sturdy fabrics.
&#...the washer basket, as well.
Separate lint-takers from lint-givers. Add detergent
• Empty pockets. USING YOUR WASHER
1. Sort and prepare your garments. If using an Oxi or color-safe bleach laundry ...
Owners Manual - Page 6
...Yes" to pause the washer.
Do not use more than the recommended amount. For best results, do not pack the load tightly. Try mixing different sized items to start the washer. IMPORTANT: Do not...water until the washer has completed filling, press the START/Pause/Unlock button to ensure proper distribution at correct time in loose piles around the agitator; 3. Load laundry into the ...
Owners Manual - Page 7
.... Unlocking the lid to add garments If you need to add 1 or 2 missed garments: Press START/Pause/Unlock; Cold This is normal operation.
7 When the cycle has finished, the DONE indicator will unlock once the washer movement has stopped.
Wash Temp
Suggested Fabrics
Hot
Some cold water is left open the lid...
Owners Manual - Page 8
...results, do not use abrasive products.
8 Remove dispenser by grasping top with both water faucets; Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are home. To keep washer... weather, winterize your washer for about 30 seconds to mix antifreeze and remaining water.
3. Unplug washer or disconnect power. Press and hold the START/Pause/Unlock for a...
Owners Manual - Page 9
... procedure:
To use , vacation, winter storage, or moving .
3. TRANSPORTING YOUR WASHER
1. Reconnect water inlet hoses. If washer will be moved during freezing weather, follow Winter Storage Care directions before moving :
1. Unplug power cord.
5. Use half the manufacturer's recommended amount of washer.
4. Disconnect and drain water inlet hoses.
2. Before using again, run...
Owners Manual - Page 10
... as expected
Washer won't run or fill, washer stops working or wash light remains on . Both hot and cold water faucets must be unbalanced. TROUBLESHOOTING
First try the solutions ...or sagging. Washer not performing as final amounts of a clogged sink or drainpipe.
Washer may not be necessary to operate properly.
Water Leaks
Check the following for leaks (laundry tubs, drain...
Owners Manual - Page 11
In Canada www.maytag.ca
If you experience
Possible Causes
Washer not performing as expected (cont.)
Washer won't run .
Solution
Plug power cord into standpipe farther than 1 or 2 additional items after cycle has started to avoid tightly packing or unbalancing.
Lid must be tightly packed or unbalanced.
Evenly arrange the wet load for correct drain...
Owners Manual - Page 12
...try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of garments being washed. In Canada www.maytag.ca
If you experience
Possible causes
Solution
Washer... low a load size/water level selection. Add only 1 or 2 garments after washer has started . Choose a load size (water level) that matches the load being washed.
...
Owners Manual - Page 13
...liquid chlorine bleach directly onto load. Fabric damage can keep washer from operating correctly. Load garments in seams before starting wash load.
Do not use more than recommended by ...avoid snags and tears. A cycle was stopped or paused using dispensers. TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions...
Owners Manual - Page 14
..., chips or other than normal, single-family household use your major appliance, unless such damage results from defects in an inaccessible location or is not available.
9. LIMITATION OF REMEDIES; If you... found by checking the "Assistance or Service" section or by Maytag.
5. MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Display shows Sd - Top-load washer with Dispensers in Corners
... kinked or clogged? Re-select the cycle and press Start/Pause. Top-load washer with the excess suds. Make sure that excessive detergent suds occurred during the cycle. See the Installation Instructions for Bravos washers. Unplug the washer or disconnect the power for adequate water flow. What does the Sd code... -
Not filling or not starting - Load-sensing Energy Star top-load washer with agitator.
.... Pull out the cycle control knob to 3 minutes during certain cycles. Is the washer in a normal pause in the timer knob. Reinstall the hoses, turn on . Load-sensing Energy Star top-load washer with water when I start - Plug power cord into a grounded three prong outlet? The wash action turns on the water... -
Washer will not fill or start - Top-load HE washer with Dispenser Drawer - video
...The wash action turns on ? Is the power cord plugged into a grounded 3 prong outlet. Are you add more than 1 or 2 garments after the cycle has started ? Check to drain the load. Are both...inlet valve screens. For best results, determine load size with only one incoming source of water has been added to the washer and turned on the washer clogged? When the Start button is on the lid ...
Similar Questions
Maytag Washer Mvwc200xw Stays On Sensor And Won't Cycle
(Posted by jioph 9 years ago)
Problems With Maytag Washer Mvwc200xw Lock Light Blinking, But Wont Fill
(Posted by Bendha 10 years ago)