Maytag MEDC300XW Support Question
Maytag MEDC300XW Support Question
Find answers below for this question about Maytag MEDC300XW.Need a Maytag MEDC300XW manual? We have 3 online manuals for this item!
Question posted by freonit on March 23rd, 2014
How To Replace Belt On Maytag Centennial Dryer Medc300xw
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MEDC300XW Manual Pages
Owners Manual - Page 2
DRYER SAFETY
2
Owners Manual - Page 4
...than four 90° elbows in the load.
Good
Better
n Remove lint and debris from the dryer. n Replace plastic or foil vent material with 4" (102 mm)
diameter heavy, rigid vent material. See "...Use the SENSOR DRY/Automatic Dry cycles to the dryer plays a big role in shrinkage, wrinkling, and static due to efficiently dry laundry.
The venting system attached to provide the most...
Owners Manual - Page 5
.../END OF CYCLE SIGNAL The End of the temperature to select available cycles on the fabrics in your laundry load. Turn the END OF CYCLE SIGNAL knob to help avoid wrinkling. See "Cycle Guide" for ...START knob to select a cycle for detailed descriptions of Cycle signal is included in your dryer. On some models, temperature is also selected.
2 TEMPERATURE / FABRIC Select a drying temperature...
Owners Manual - Page 6
...heat drying.
Line dry bonded or laminated fabrics.
Drying time varies based on the fabrics in your dryer has multiple heat settings:
A High Heavy temperature setting may be used for the specified time on... are still damp.
Senses moisture in the shortest time. Settings and options shown in the dryer too long. Items to dry:
Heavy or bulky items Any load
Cycle: High Heat Freshen...
Owners Manual - Page 7
Clean the lint screen
2. Place laundry in the dryer. Some models have a different door than the one shown. Roll lint off the screen with a .... Push the lint screen firmly back into place.
clothes should be able to remove lint.
Load the dryer
Clean the lint screen before operating this dryer. Do not rinse or wash screen to tumble freely.
7 Close the door. NOTE: Your model may...
Owners Manual - Page 8
...DRY/AUTOMATIC DRY cycles.
4. Promptly removing clothes at the end of the fabrics at which the dryer will shut off.
See "Setting the Drying Temperature".
8 Drying time varies based on some ... dealer from whom you may want to put on a hanger to "Assistance or Service" on your dryer, please refer to complete drying. DRYING RACK
To purchase a drying rack for loads you purchased your...
Owners Manual - Page 9
... completely dry. n If lint falls off the screen with the brush to avoid drum staining. The screen is in dryer.
9 Thoroughly dry lint screen with hot water. 5. Pull the lint screen out of clothes.
As needed cleaning Laundry detergent and fabric softener residue can cause overheating and damage to stop before your...
Owners Manual - Page 10
... sure leveling legs are at fuse or breaker box. 2.
Unplug dryer or disconnect power.
2. Remove the cover.
3. Turn off valve to secure dryer door. Moving Care
For power supply cord-connected dryers: 1. Open the dryer door. Replace the bulb with the screw.
4. For gas dryers: 1. Use tape to gas supply
line. 3. Unplug the power supply cord...
Owners Manual - Page 11
... has too many turns.
Replace both fuses or reset the circuit breaker. TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call an electrician. In Canada www.maytag.ca
If you hear the dryer drum moving. The Air...
Owners Manual - Page 12
... cycle. Use Timed Dry for the first time. Lint screen should be cleaned before removing laundry from dryer at the beginning of the cycle.
Odors
You have an odor. A high temperature cycle ... dryer fabric softener sheets at the end of drying time in clothing (usually blue jeans).
Dryer tightly packed. If so, ventilate the area. This reduces overdrying.
12 In Canada www.maytag.ca...
Owners Manual - Page 13
... accordance with Maytag published installation instructions.
10. Replacement parts or ...MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of your major appliance, to instruct you on how to use your major appliance, to replace...
Installation Instructions - Page 2
... not followed. These words mean:
DANGER
You can be killed or seriously injured if you don't follow the instructions provided with any tools listed here.
DRYER SAFETY
Your safety and the safety of injury, and tell you what the potential hazard is the safety alert symbol.
Always read and obey all...
Installation Instructions - Page 3
... outlet located within 2 ft. (610 mm) of either side of 1" (25 mm) under entire dryer. (If slope is located in garages, closets, mobile homes, or sleeping quarters. Check existing electrical supply...Venting Requirements."
■■ A separate 30 amp circuit.
■■ If you purchased your dryer. Drying times can be installed or stored in an area where it will need:
■■...
Installation Instructions - Page 4
... cord.
■■ If codes permit and a separate ground wire is used when the dryer is installed in conformance with elbow. The neutral ground wire is suitable for mobile home installations....and secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is installed with a door, minimum ventilation openings in mobile homes to an individual branch...
Installation Instructions - Page 5
... or spade terminals with ring or spade terminals and UL listed strain relief. Slide the dryer until diamond marking is close to finish turning legs until it is no longer visible. ...cord kit marked for leveling legs
To avoid damaging floor, use a large flat piece of cardboard from dryer carton; The wires that connect to do not use with flexible metallic conduit.
If your outlet looks ...
Installation Instructions - Page 7
... relief
B
Put power supply cord through the strain relief. Do not further tighten strain relief screws at this page. Tighten screw.
7
Spade terminals with the dryer cabinet and be in place. Attach power supply cord
A
to connect neutral
ground wire and neutral wire.
2.
For 4 wire Power Supply Cord Connection, continue to...
Installation Instructions - Page 8
... screws. Now, go to external ground conductor screw (A).
Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Spade terminals with hold -down screw. 5. Connect neutral wire
BC
Connect neutral wire (white or center...
Installation Instructions - Page 9
...
to strain relief
(127
5" mm)
Direct wire cable must have a tight fit with the dryer cabinet and be moved if needed. Cut 11/2" (38 mm) from external ground conductor screw...
4-wire Direct Wire Connection
1. The strain relief should have 5 ft. (1.52 m) of extra length so dryer may be in a horizontal position. Tighten strain relief screws.
Shape ends of wire under terminal block screw, ...
Installation Instructions - Page 10
...wires
To connect wires to terminal block
F
Connect ground wire (green or bare) (F) of extra length so dryer may be moved if needed. Connect ground wire
A
(893m½m" )
Direct wire cable must have 5...end together and tighten screw.
5. Strip 31/2" (89 mm) of outer covering from end of dryer rear panel. If using 3-wire cable with ground wire, cut bare wire even with hold-down ...
Installation Instructions - Page 12
...; Use clamps to seal all governing codes and ordinances.
Do not use a heavy metal vent.
Dryer exhaust must not be used .
■■ Do not use plastic or metal foil vent. Do... WARNING: To reduce the risk of a building. Replace plastic or metal foil vents with screws or other fastening devices that may result in final dryer location. ■■ Remove excess to clean)...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
My dryer makes sounds or vibrations
...the load knotted or balled up . Laundry items with rivets and buckles. Play the sound of a dryer running with a towel load inside the dryer along the front and rear edges of the... should stop. Normal dryer sounds: The following are missing. Replace any of the four dryer legs are normal sounds of a dryer. Is there a clicking sound? (Gas dryers only) The gas valve... -
Display shows L2 - Dryer
... is not turning and there is the load not tumbling? Electric dryer Select a Timed Dry heated cycle, and restart the dryer. If the problem continues, call an electrician. Replace the fuse(s) or reset the circuit breaker(s). The drum may not have heat? This code indicates that there may be turning... -
Purchasing compactor bags
...F9A75Q4 in varying quantities that will save you check out. | Laundry Overview Washers Dryers Accessories Refrigeration Refrigerators Freezers Cooking Ranges Built-In Ovens Cooktops Microwaves ... or its related companies. All Maytag replacement bags ensure effective trash management and compactor performance. Purchasing replacement compactor bags is your appliance? Trademark/TM...
Similar Questions
How To Disassemble Maytag Centennial Dryer Medc300xw
(Posted by gergmtah 9 years ago)
How To Replace Belt On Maytag Centennial Dryer Model Number Medc300xw
(Posted by Karst 10 years ago)
How To Test An Maytag Centennial Dryer Timer Mod# Medc400vw0
how to conduct an ohm test on a timer on the maytag centennial dryer medc400vw0?
how to conduct an ohm test on a timer on the maytag centennial dryer medc400vw0?
(Posted by josephboone137 10 years ago)
How Do You Replace The Belt On A Maytag Centennial Dryer Medc300xw0
(Posted by jcre 10 years ago)