Maytag MED9600SQ Support Question
Maytag MED9600SQ Support Question
Find answers below for this question about Maytag MED9600SQ - Epic 7.0 cu. Ft. Electric Dryer.Need a Maytag MED9600SQ manual? We have 1 online manual for this item!
Question posted by gstelpstra on September 29th, 2016
Error Code E3
Does this code mean that the circuit board is shot or is there a reasonable way to fix it? We were quoted $300 to fix ???
Current Answers
Answer #1: Posted by Odin on September 29th, 2016 5:11 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
See this workaround: https://www.youtube.com/watch?v=fx7Lrj7gEy4
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Maytag MED9600SQ Manual Pages
Use and Care Guide - Page 3
... before using the dryer, follow the safety alert symbol and either the word "DANGER" or "WARNING."
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury... See installation instructions for grounding requirements.
These words mean:
DANGER
You can be exposed to catch fire.
s Do not reach into the dryer if the drum is the safety alert symbol. ...
Use and Care Guide - Page 4
... whom you planning to stack your dryer or refer to the "Assistance or Service" section of this manual. Parts needed Check local codes.
Ask for Part Number 8541503.
...You may select a 15.5" (39.4 cm) pedestal. Check existing electrical supply and venting. Optional pedestal
To order, call the dealer from dryer drum. s Flat-blade screwdriver
s #2 Phillips screwdriver
s Adjustable ...
Use and Care Guide - Page 5
....7 cm) clearance behind the dryer for a garage installation. s A separate 30-amp circuit. s A sturdy floor to place the dryer at least 18" (46 cm) above the floor.
If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. At lower temperatures, the dryer might be installed or stored...
Use and Care Guide - Page 6
...(2.5 cm) (2.5 cm)(68.6 cm) (2.5 cm)
*Required spacing **For side or bottom venting, 0" (0 cm) spacing is allowed. Dryer on pedestal
14" max.* (35.6 cm)
18" min.* (45.72 cm)
1" (2.5 cm)
27" (68.6 cm)
A
1"..., 0" (0 cm) spacing is allowed. Closet installation -
Recessed area B. Recessed or closet installation - Dryer only
14" max.* (35.6 cm)
18" min.* (45.72 cm)
48 in.2* (310 cm2...
Use and Care Guide - Page 7
...wire power supply cord, at least 4 ft (1.22 m) long.
Additional installation requirements This dryer is isolated from your dealer.
Only
It...circuit. s If local codes do not use with a 3-wire electrical supply connection.
The opening (such as the dryer exhaust opening.
If your responsibility s To contact a qualified electrical installer. If connecting by a white cover. Electrical...
Use and Care Guide - Page 8
... the line.
Be sure wall receptacle is properly installed and grounded in death or electrical shock.
Check with the circuit conductors and connected to whether the dryer is 5 ft (1.52 m) in a risk of this manual. SAVE THESE INSTRUCTIONS
Electrical Requirements -
SAVE THESE INSTRUCTIONS
It is recommended.
WARNING: Improper connection of the equipment-
GROUNDING...
Use and Care Guide - Page 9
... up B. Ground wire (green or bare wire) must be connected to green ground connector. Securely tighten all electrical connections. The strain relief should have a tight fit with the dryer cabinet and be in death, fire, or electrical shock.
Failure to center terminal (silver). Remove the hold -down
s Put power supply cord through the...
Use and Care Guide - Page 10
...) of the strain relief through the strain relief. A
B
C
A. Electrical Connection Options
If your type of electrical connection: 4-wire (recommended)
3-wire (if 4-wire is required for your...dryer power supply cord*
3-wire connection: Power supply cord
3-wire direct
3¹⁄₂" (8.9 cm)
A fused disconnect or circuit breaker box*
3-wire connection: Direct Wire
*If local codes...
Use and Care Guide - Page 11
...
IMPORTANT: A 4-wire connection is required for mobile homes
and where local codes do not permit the use of power supply cord C 1.9 cm) UL... or center wire)
4. Tighten screw. You have 5 ft (1.52 m) of dryer rear panel. Neutral wire (white or center wire)
E.... conductor screw -
Direct wire cable must have completed your electrical connection. A. Neutral wire (white or center wire) ...
Use and Care Guide - Page 12
...dryer rear panel. Neutral wire (white or center wire) E 1.9 cm) UL listed strain relief
3. You have completed your electrical connection. Now go to
"Venting Requirements."
3-wire connection: Direct wire
Use where local codes... G. Secure cover with hold -down screw.
7. Direct wire cable must have 5 ft (1.52 m) of wires into a hook shape.
1
12 Shape ends of extra length so...
Use and Care Guide - Page 13
...C A
Optional 3-wire connection
Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to "Venting Requirements."
4. Tighten screw. Connect... screws.
4. Tighten screw. You have completed your electrical connection. Insert tab of terminal block cover into slot of dryer rear panel. When connecting to the terminal block, place...
Use and Care Guide - Page 14
...or a concealed space of fire, this manual.
Do not use a plastic vent. The dryer exhaust must be purchased from the entire length of the system and make sure exhaust hood ...vent. B
A
4" (10.2 cm) 4" (10.2 cm) A.
Failure to seal all governing codes and ordinances.
Venting Requirements
WARNING
Rigid metal vent
s For best drying performance, rigid metal vents are acceptable...
Use and Care Guide - Page 15
...) 279820 (black) Contact your exhaust installation type
Recommended exhaust installations Typical installations vent the dryer from the rear of the exhaust (such as flowers, rocks or bushes, snow line,...from entering the home. Improper venting can result in death, fire, electrical shock, or serious injury. Dryer B. Select the type best for close -clearance installations are possible. ...
Use and Care Guide - Page 16
...ft (20 m) 58 ft (17.7 m)
Flexible metal 36 ft (11 m) 28 ft (8.5 m)
1
Rigid metal
54 ft (16.5 m) 48 ft (14.6 m)
Flexible metal 31 ft (9.4 m) 23 ft (7 m)
2
Rigid metal
44 ft (13.4 m) 38 ft (11.6 m)
Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)
3
Rigid metal
35 ft (10.7 m) 29 ft (8.8 m)
Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)
4
Rigid metal
27 ft (8.2 m) 21 ft... of the dryer (not the...
Use and Care Guide - Page 17
...a carton corner post from the inner door assembly (see illustration).
Remove the door.
3. Lay the dryer door on the work
surface. 2. Remove the 6 screws to connect the exhaust vent.
Set the ... not crush or kink vent. 3. (On gas models) Check that the vent is no kinks in dryer. Reverse Door Swing
You can change your door swing from the top).
5. Place the inner door, screw...
Use and Care Guide - Page 18
... a screw in first, the door will not start the dryer. Check that the dryer is intact and tight, or circuit breaker has
not tripped.
s Dryer is plugged into a grounded outlet. s Use a small ...this screw first.
7. s For power supply cord installation, plug into a grounded outlet and/or electrical
supply is an extra part, go back through the steps to the other side and reattach with the...
Use and Care Guide - Page 19
... heat.
Your dryer may notice a burning odor when the dryer is an estimated length of fire, electric shock, or injury...dryer and shut door.
3.
Pressing the Manual Dry Time (- If you feel for Automatic Cycles. Failure to an Automatic Cycle.
Place laundry ... refer to start your dryer.
Do not dry anything that has ever had anything that both circuit breakers have all of ...
Use and Care Guide - Page 20
...and Dryness Level are available. or +) buttons. s Press and hold ) HOLD TO START button until dryer starts (about 1 second). s Press the CYCLE END SIGNAL button to set signal volume to reduce wrinkling...when they tumble. s Refer to the Automatic or Manual Preset Cycle Settings chart (in the dryer drum help save time, avoid overdrying, and increase the accuracy of a Manual Cycle by ...
Use and Care Guide - Page 25
... front to back and side to restart the dryer. Electric dryers use ?
s "PF" (power failure), check the following: Was the drying cycle interrupted by a power failure? s "E" Variable (E1, E2, E3) service codes: Call for 2-5 seconds. Make sure leveling legs are intact and tight, or that both circuit breakers have heat. Replace the bulb with a qualified electrician...
Use and Care Guide - Page 28
... defects in which it was purchased. The removal and reinstallation of purchase, when this book and your authorized Maytag dealer to or furnished with electrical or plumbing codes, or use your major appliance to use of the Use & Care Guide. After checking "Troubleshooting," additional help you obtain assistance or service if you...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How to remove odors from a front-load washer with the Clean Washer cycle (on control panel)
...See: How do I clean my Epic® If odor persists, repeat the procedure one or two more times. Use warm or hot water in your washer. If your laundry room is soil that the Affresh ... Washer cycle. Press Start. The cleaning cycle may reduce the effectiveness of the washer interior. If an error code, ("rL" or "F-34") is complete, wipe the washer with the Clean Washer cycle (on control ... -
Display shows an error code - Front-load washer
... power. Front-load washer Display shows F20 or FH - Check the following list of codes indicates an electronics communication problem with the washer: Epic ® Display shows an error code - Front-load washer My front-load washer display shows an error code. Front-load washer Display shows F22 or FdL - F05, F07, F09, F10, F11, F13... -
Display shows an error code - Dryer
Check the following list of codes indicates a possible problem with the dryer: Epic ® Dryer Display shows AF - If the error code remains on the display, call for error-code related issues you can correct: Display shows PF - Dryer My dryer display shows an error code. E1, E2 and E3 Epic Z TM dryer - Dryer Display shows L2 - F01, F02, F22, F23, F24, F25, F26, F28...
Similar Questions
Error Code P01 On Maytag Gas Dryer Mgde500vw
What does error code P01 relate to on Maytag gas dryer MGDE500VW
What does error code P01 relate to on Maytag gas dryer MGDE500VW
(Posted by dagzik 8 years ago)
What Does An F23 Error Code Mean On My Mede300vf
(Posted by Anonymous-147988 9 years ago)
Error Code F 01 On Maytag 3000 Series Dryer.
Dryer Worked Fine An Hour Ago, And Now When I Try To Dry Last Load Of Laundry, It Makes A 'clicking'...
Dryer Worked Fine An Hour Ago, And Now When I Try To Dry Last Load Of Laundry, It Makes A 'clicking'...
(Posted by gwyndehn 9 years ago)
Error Code F-01
I have an Epic Z Model #MEDZ600TE2 electric dryer that turns on but won't run. It is giving an error...
I have an Epic Z Model #MEDZ600TE2 electric dryer that turns on but won't run. It is giving an error...
(Posted by eaathey 10 years ago)
Matching Stacking Kit
Matching stacking kit Maytag/MED9600SQ-epic-70-cu-ft-electric-dryer/21808 with regards, Vinesh
Matching stacking kit Maytag/MED9600SQ-epic-70-cu-ft-electric-dryer/21808 with regards, Vinesh
(Posted by vineshjosep 11 years ago)