Home » Maytag » Laundry Washers » Maytag MAT14CSAWW

Maytag MAT14CSAWW Support Question

Find answers below for this question about Maytag MAT14CSAWW - Commercial Washer.
Need a Maytag MAT14CSAWW manual? We have 1 online manual for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by subashramkaran on May 4th, 2017

Machine Won't Fill With Cold Water. Works Good With Hot. Cold Supply Good.

Money goes in. Machine comes on. Fill with hot water. Goes through cycle perfectly. Put on cold water, goes through process of filling with cold water, but does not fill. Machine then times out of cycle.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by waelsaidani1 on May 7th, 2017 11:58 PM

This answer was accepted by the poster of the original question.

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,797

1,100
points

Turn wall valve off for cold water. Remove cold water hose connection from washer and check washer inlet valve screen for blockage. Run cold water directly into washer from hose to make sure you have good water pressure.

Related Maytag MAT14CSAWW Manual Pages

Installation Instructions - Page 1

...le Numéro de série Date d'achat W10135312B www.maytagcommerciallaundry.com INSTALLATION INSTRUCTIONS COMMERCIAL WASHER 120-volt, 60-Hz Models INSTRUCTIONS D'INSTALLATION DE LA LAVEUSE COMMERCIALE Modèles ...120 V, 60 Hz Write down the model and serial numbers before installing washer. Both numbers are listed on the model/serial rating plate located under the lid. ...

Installation Instructions - Page 2

...4 Electrical Requirements 5 INSTALLATION INSTRUCTIONS 6 Remove Shipping Strap 6 Connect the Hoses 6 Level the Washer 7 Complete Installation 8 ELECTRONIC CONTROLS SETUP 10 WARRANTY 14 Table des matières SÉCURIT... l'installation 21 RÉGLAGE DE LA COMMANDE ÉLECTRONIQUE 23 GARANTIE 27 WASHER SAFETY Your safety and the safety of injury, and tell you what the potential...

Installation Instructions - Page 3

... a hot water system that all parts were included. 1 hose clamp 2 inlet hoses 4 flat water hose washers 2 front-leveling legs with a maximum slope of 10-100 psi (69-690 kPa). Gather the required tools and parts before starting installation. Parts supplied Remove parts bag from each for grounding instructions. flammable, or explosive substances to the washer. machine, turn...

Installation Instructions - Page 4

...may be installed in a recessed area or closet. Water inlets H. 7" (180 mm) I D A B G C E Cold Hot J N F M L H O K A. ... *Opening is recommended to reduce noise transfer. Power supply cord J. Drain hose connector K. Louvered doors with equivalent...washer is the minimum for a closet door. Product Dimensions H I . Recessed Area and Closet Installation Instructions This washer ...

Installation Instructions - Page 5

... of the above code standards can result in accordance with a power supply cord having a 3 prong grounding plug. or 20-amp, fused electrical circuit is recommended. A time-delay fuse or circuit breaker is required. Do not use an adapter. IMPORTANT : The washer must be obtained from: National Fire Protection Association One Batterymarch Park, Quincy...

Installation Instructions - Page 6

...back of the washer. Do not strip or crossthread. Estimate the length of drain hose needed when washer is held tightly ...water leakage. Cold water inlet valve B. NOTE: Inlet valve threads are plastic. Insert new flat washers (supplied) into laundry tub or standpipe. 3. Firmly seat the washers...hoses. Attach second hose to the washer 1. INSTALLATION INSTRUCTIONS WARNING Excessive Weight ...

Installation Instructions - Page 7

... additional two-thirds turn to hot water faucet. Use the leveling legs and nuts from under washer. 7 Place the hose clamp over drain hose. Repeat with other corner posts on top of washer. 5. Remove cardboard or hardboard from the parts package. Move washer to faucet by hand. 3. Check for good fit. Tilt washer backward and remove corner...

Installation Instructions - Page 8

.... Plug power supply cord into a grounded 3 prong outlet. If the timer is advanced partially into the cycle causing the start button to floor. 2. Do not overtighten; then front to the end of the cycle. If nuts are now installed. Allow timer to advance to back. Check the electrical requirements. Gently lower washer to be...

Installation Instructions - Page 9

... be left in the washer, run the washer through a complete cycle with No washer can Do not dry anything that has ever had any residue away that are washed in the washer. Do not drop washer while using hand truck. 9 Checklist for washer operation: Check the following if the washer is not blown. 3. Power supply cord is recommended that...

Installation Instructions - Page 10

... Electronics ESD problems are present everywhere. It will flash 'SELECT CYCLE'. 0 MINUTES PRICE 2.00 GENERAL USER INFORMATION Blank Display This condition indicate the washer is debit card 'cable' ready. Free Cycles This is restored to ESD stress. ELECTRONIC CONTROLS SETUP BASIC OPERATION OF COMMERCIAL WASHER For additional information, see www.MaytagCommercialLaundry.com. This tech sheet...

Installation Instructions - Page 11

...commercial washer, hook it up, plug it in, and have access to next code. 8 2 1 RINSE CYCLES 821 This is indicated by the one (1) per second. 3. The LOWER MIDDLE key pad will advance from code to program the controls 1. To access connector AA1: � Unplug washer...up card (supplied by pressing .... 1. 0 0 MONEY COUNTER OPTION This option...key pad 3 consecutive times to next code. ...

Installation Instructions - Page 12

...SELECTED (cont.): 5. 0 0 TIME-OF-DAY CLOCK, MINUTES 5. 0 0 This is the TIME-OF-DAY CLOCK, hour setting; Select START HOUR by depositing extra money. A number followed by '0'... 9. 1 0 This represents the day of different prices for cold, warm, and hot water cycles. This option causes the customer display to the programmed wash time. 02 - Press the LOWER RIGHT key pad for that particular...

Installation Instructions - Page 13

... advance to next code. If money counter (1.0C or 1.C0) is selected, the following is installed in washer or reconnect power. 13 CODE EXPLANATION COIN/DEBIT OPTION Both coin & debit selected. Enhanced Debit is self-selected when a Generation 2 card reader is true: 100 Represents the number of cycles in HUNDREDS. 1 02 = 200 200...

Installation Instructions - Page 14

MAYTAG® COMMERCIAL SINGLE-LOAD AND VENDED MULTI-LOAD WASHER AND DRYER WARRANTY LIMITED WARRANTY ON PARTS For the first five years ...wiring or plumbing. 3. If you how to instruct you need service, please contact your authorized Maytag® Commercial Laundry distributor, or for other costs including labor, transportation, or custom duties. 2. ITEMS MAYTAG WILL NOT PAY FOR 1. To...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

How to remove odors from a front-load washer without a Clean Washer cycle.
... washer cleaner method (recommended) NOTE: Completely read these instructions before using the correct amount of fabric softener. Always do I find my model number? Use warm or hot water in your washing machine unless the fabric you are washing requires cold water. See your Use and Care Guide for better ventilation and drying of more times...
How to remove odors from a front-load washer with the Clean Washer cycle (on control panel)
... in combination with Clean Washer cycle Affresh washer cleaner method (recommended) Completely read these instructions before beginning the cleaning process. Do not add detergent or other laundry products to thoroughly clean the inside of the washer interior. If odor persists, repeat the procedure one or two more times. Use warm or hot water in my front-load...
My washer does not have water hoses
...dishwashers. Leaking water - Bravos washer with water hoses? My washer does not have water hoses Why didn't my washer come with Dispensers in the Review Order screen when you check out. Water inlet hoses are wrinkled - Top-load washer FAQs Knowledgebase search tips Recommended installation for electrical, drain and water supply connections for both hot and cold water and to...