Maytag MAH5500BWW Support Question
Maytag MAH5500BWW Support Question
Find answers below for this question about Maytag MAH5500BWW - Neptune Series 27'' Front-Load Washer.Need a Maytag MAH5500BWW manual? We have 2 online manuals for this item!
Question posted by Drewdo2 on March 26th, 2013
Model Mah5500bww. Will Not Drain All Water. Has Wrong Display Of Cycle Time
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MAH5500BWW Manual Pages
Use and Care Guide - Page 5
... the wash and rinses for cleaning moderately soiled loads. rinse -
Do not overload the washer.
4 The Quick setting offers a quick cycle time. Suggested uses include freshening newly purchased clothes, or clothing that has been packed away. Use for jeans, towels and bedding. stain cycle -
Removes more completely remove laundry additives and perfumes. use for cleaning heavily...
Use and Care Guide - Page 6
... attempt to stop the washer. ESTIMATED TIME DISPLAY
After pressing start /pause pad to open easily.
INDICATOR LIGHTS
Door locked - Fill time will vary with each load.The Maytag® Neptune® clothes washer uses an adaptive fill valve to increase or decrease the end of cycle signal volume. Step 7
START YOUR MAYTAG NEPTUNE® WASHER
• Close the door...
Use and Care Guide - Page 7
... using regular detergent formulated for top-loading washers, it is best if both laundry products are in your area.
6
Pour the recommended amount of laundry detergent directly into the dispenser, close attention to the soil level of the respective manufacturers. ** To determine water hardness in your area, contact your local water utility or State University Extension...
Use and Care Guide - Page 9
... - CLEANING THE DISPENSER
To clean and freshen the washer interior: 1. Fill the bleach dispenser with soap and water. Hard water deposits may remain in the washer as usage, the amount of dirt, soil or bacteria being run through a complete cycle using hot water. 5.
NOTE: Do not use any excess laundry additives. If this should be cleaned and...
Use and Care Guide - Page 11
...; Reduce detergent amount for that specific load size, soil level and water hardness. • Use high efficiency or low sudsing detergent specially formulated for obstructions. Eliminate kinked hoses. BEFORE YOU CALL
CHECK THESE POINTS IF YOUR MAYTAG® NEPTUNE® WASHER... It should be warm. Fills with the Wrong Temperature Water
• Turn both faucets on...
Use and Care Guide - Page 13
.... Check for a plugged stand pipe.
The washer has repeatedly tried to fill. The washer has tried to unlock the door but has been unsuccessful.
Call for a kinked drain hose. Make sure the water faucets are open when starting a cycle or the door is a safety feature. The door must be displayed to make sure power cord is...
Use and Care Guide - Page 14
... a liquid and is started. OR Water flows through the dispenser to make a series of -balance load. The motor increases speed to spin the tub to redistribute the load more water during a spin cycle. Fabric softener is dispensed during final minutes of the cycle. Clothes washer maintains a slightly reduced spin speed after the washer has been tumbling for maximum performance...
Service Manual - Page 12
... the Max Extract profile regardless of -balance condition, the signal will be run when the washer is started. NOTE: If the user selects the Hand Washables fabric selection, all spins will...the pressure switch. When the water level in sequence. Figure 1-8
Series 17 & Later
INPUT DEFINITIONS
DOOR LOCK SWITCH INPUT When input is present, this is energized and the cycle has finished, the machine ...
Service Manual - Page 13
... disengage the line relay to stop the washer.
During the drain and spin increments after two minutes, it will disengage the line relay, both water valve output signals, the door lock wax...next increment and continue with a 30 second drive cycle and a 5.8 second advance time (See Timer Input Charts).
When the washer is at 14 times the speed of the switched reluctance motor.
If the...
Service Manual - Page 19
... approximate and will go into a suds reduction routine, consisting of a series of the cycle.
3. Clothes Wet at the end of additional rinse and partial drain cycles to retract at End of suds. N on water fill times, due to types of clothing loads, available water pressure and the time for the door lock system to reduce the suds present (See...
Service Manual - Page 37
...the siphon cap to see if the cap was placed on the water valves. If the timing is energized for five minutes without the cycle inputs changing, the machine control board will drop the line voltage...Dispense:
Usually this occurs when the door is remounted into the shroud evenly prior to the washer shutting down too soon or execessive suds present. Also, check the drive belt for excess ...
Service Manual - Page 88
...Models MAH4000 & MAH5500A. We suggest you file this manual supplement: MAH4000 MAH5500A
CONTENTS
SECTION 1. WASHER CONTROLS OVERVIEW 3 SECTION 5. CYCLE REVIEW 4
Stain Cycle 4 Cycle Times 6 SECTION 6. WIRING INFORMATION 14
For additional information on material covered in this with your 16008373 Manual for service manual 16008373, which replaces supplement two (16008373-02). WATER...
Service Manual - Page 92
The washer will vary based on water fill times, due to types of Spin)
Tumble Pattern - The total cycle times are approximate and will go into a suds reduction routine, consisting of a series of additional rinse and partial drain cycles to retract at End of clothing loads and the time for the door lock system to reduce the suds present. (See Troubleshooting...
Service Manual - Page 110
... A Complete Wash Cycle
There are similar to the MAH4000 washer, with the exception being they do not have a 7/3 tumble pattern. Wash/rinse temperature selection determines water fill temperature. For this initial period. The door is selected and started . Once filled, the tumble pattern and the total wash time depends on the MAH7500A model. General Information...
Service Manual - Page 115
... change .
In this mode, time is not lit. Washer Controls Overview ©2001 Maytag Appliances Sales Company
2-3 When the door is finally unlocked, the door locked LED is increased in that wash cycle shall be changed at any time. After 5 seconds, the estimated time remaining for the total cycle will be displayed and the wash level LED...
Service Manual - Page 118
...the washer door is reached, the circuit opens and the machine control de-energizes the Water Valve Outputs. CYCLE SEQUENCE DEFINITIONS
IDLE/PAUSE MODE (LED Model) ...time
heater. User Selections
Input water tempered
Cold Wash no Hot water
N/A
heater
Hot Wash with Hot water, then Main
stain cycle and heat to 105°F if
wash time
necessary
During a warm wash the cold may be cycled...
Service Manual - Page 122
... has made while in the interactive mode will continuously display the touch screen on in unison. The segments on the display are generally logged dentified when the severity level of the washer during operation and identify any time. LCD Washer This mode will not be run a cycle.
When this occurs, the user is able to navigate...
Service Manual - Page 125
... code happened on above the Stain Cycle key. All output will display and turn on the bottom of a diagnostic code. Key Pressed: Cotton/sturdy Wrinkle Free Delicates Hand Wash Presoaks Stain Cycle Extra Rinse
Max Extract
Function Performed
Hot Water Valve
Cold Water Valve
Bleach Valve
Fabric Softener Valve
Drain Pump
Motor Control Unlock Door (Sends...
Service Manual - Page 130
... cold water on bleach valve on fabic softener on
drain on motor control
on heat on the display panel.. Help codes: Display all diagnostic codes.
Software version: Display current software version
For a listing of help codes, see Section 5: DIAGNOSTIC/ HELP CODE TABLES.
16010486 (16008373-05) Revised 02/01
Section 2. If the washer is already running a wash cycle...
Service Manual - Page 143
...) Revised 02/01
Section 4. input
P1(8)
P8(2)
120 VAC
Hot water valve output
P1(3)
P8(2)
120 VAC
L1- page 4-8 LCD model only (3K-18K ohms) 10K-85K ohms)
INPUT/OUTPUT VOLTAGES (LED Washer)
Description
Connector/ Connector/ Voltage Pin Number Pin Number
Bleach water valve output
P1(5)
P8(2)
120 VAC
Chassis Ground
P3(1)
Ground
Cold...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Sounds during drain - Front-load washer
... a longer period of time. The drain portion of the cycle usually lasts 3-5 minutes. Is this continuous running, the pump will be some models), or use our search feature below to hit the cabinet, a knocking noise will continuously run to remove the water released from the load. Due to move. front-load washer Display shows F21 or F02... -
The cycle time is not correct - Front-load washer
... quality of load, cycle selection, and household water temperature and pressure. Washer not draining, not spinning out water; wet loads - Does the time displayed show one value for a long period of time, or jump to zero at one number for the conditions listed above, so the actual time required may occur several attempts to redistribute the laundry load in... -
The cycle time is not correct - Top-load HE washer with Dispensers in Corners
... occur with Dispensers in Corners Not draining, not spinning out water, wet loads - The display indicates too much suds and washer is detected, then the washer will prevent this occur with a single item or bulky item load? Top-load washer with Dispensers in Corners The cycle time is not correct - The cycle time is not correct on your...
Similar Questions
Maytag Mah5500bww - Neptune Series 27'' Front-load Washer
My Neptune washer cycles and agitates through the rinse cycle but once the timer reaches 5 min or le...
My Neptune washer cycles and agitates through the rinse cycle but once the timer reaches 5 min or le...
(Posted by danjo29 5 years ago)
How To Hang Drain Hose Maytag 2000 Series Front Load Washer Manual
(Posted by joeJBass 9 years ago)
Maytag Neptune Washer Model# Mah5500bww Will Not Advance To Spin Cycle
(Posted by NY81pamsi 10 years ago)
Maytag Neptune Mah Front Load Washer Will Not Drain
(Posted by cuB1Bobs 10 years ago)
Wash Cycle Times
Why are the wash cycle times so much longer than the time display indicates? Water pressure is good,...
Why are the wash cycle times so much longer than the time display indicates? Water pressure is good,...
(Posted by karenteitel 13 years ago)