Makita RT0700C Support Question
Makita RT0700C Support Question
Find answers below for this question about Makita RT0700C.Need a Makita RT0700C manual? We have 4 online manuals for this item!
Question posted by gaanniery on June 5th, 2014
Straight Guide
Is there an additional guide for RT07900c for closer work
Current Answers
Answer #1: Posted by TechSupport101 on June 5th, 2014 10:19 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,325
Member since:
May 24th, 2013 Points: 12,171,325
Related Makita RT0700C Manual Pages
Owners Manual - Page 2
... programme of flammable liquids, gases or dust. Keep work area clean and well lit. Electrical Safety 4. If operating a power tool in the presence of research and development, the specifications... (Original instructions)
SPECIFICATIONS
Model
RT0700C
Collet chuck capacity
1/4", 3/8"
No load speed (RPM)
10,000 - 30,000/min. The term "power tool" in serious personal injury. 11...
Owners Manual - Page 3
... the current your product will do not allow persons unfamiliar with these instructions, taking into account the working conditions and the work by insulated gripping surfaces, because the cutter may lead to loss of the power tool is in a hazardous situation. Handle the bits very carefully. Check the bit carefully for your power...
Owners Manual - Page 4
... burn your skin.
15. Take caution to secure the tool base. Bit protrusion
2
2. ON ( I )" side of the following features. Some material contains chemicals which may be toxic. SAVE THESE INSTRUCTIONS. OFF (O) side
1
3. Do not smear the tool base carelessly with electronic function are working with product
(gained from workpiece.
14. Possible to safety...
Owners Manual - Page 5
...1, or the speed adjusting function may no longer work on the dial and the approximate tool speed. Refer to the table for the relationship between the number settings on the tool.
3
1
2
1.
Loosen 3. OPERATION
For... in the direction of number 1. Dust nozzle 2. Thumb screw 3. Hold
3
2
011835
The tool speed can be turned only as far as 6 and back to be changed by pressing the ...
Owners Manual - Page 6
... wish to keep it flush with the side of the workpiece.
011838
The templet guide provides a sleeve through which the bit passes, allowing use of the tool 4. Workpiece 6. WARNING: • Before using the trimmer shoe, the straight guide or the trimmer guide, be more than 3 mm (1/8") deep, make a sample cut grooves more than 3 mm (1/8") at...
Owners Manual - Page 7
... the circle to be cut a slightly different size
from the templet. Wing nut 2. Base
3
4
011841
When cutting, move the tool with the straight guide flush
with the clamp screw (A). Wing nut
3
4
A
011842
Circular work Circular work may be cut (distance between the center of circle and the center of bit) are as shown in the...
Owners Manual - Page 8
... which has been removed from the tilt base on the tool base with the clamp screw (A). Screw
4
011845
When cutting, move the tool with the trimmer guide. Install the trimmer guide on the trimmer base allows the change of the workpiece.
1. Clamp screw (A)
2. Straight guide 1 2
3
011843
Trimmer guide (optional accessory)
Tilt base (optional accessory) Tilt base (optional...
Owners Manual - Page 9
...
Secure it with the offset base on the offset base.
1. Collet cone
011860
Mount the tool on the offset base, remove the collet nut and collet cone by pressing the shaft lock ...
012085
(1) Offset base (optional accessory) is convenient for work in a tight area such as shown in the figure.
3
011992
To install the bit, fall the tool with a locking lever on its entire belt width fits...
Owners Manual - Page 10
...with a plunge base (optional accessory)
CAUTION: • When using as a router, install the tool on the grip attachment. Bar type grip
(optional
1
accessory)
3
011984
In another way of use... is removed from the offset base. Screw 1 2. Grip
2
1
011855
To use the tool as a router, hold the tool firmly with a trimmer base and a grip attachment (optional accessory) for more stability.
1
...
Owners Manual - Page 11
... and advancing smoothly until the bit just touches the flat surface. View from the top of the tool 4. Moving the tool forward too slowly may cause a poor quality of cut without the bit making any contact. Straight guide
4
001985
11 Stopper pole
setting nut 5. Turn the stopper pole setting nut counterclockwise. Lower the stopper...
Owners Manual - Page 12
... (optional accessory)
1
2
3
011849
To install the straight guide, insert the guide bars into the holes in place. When cutting, move the tool with the straight guide flush
with the wing nut. Feed the tool in the plunge base. Templet guide (optional accessory)
011848
The straight guide is not straight, the straight guide cannot be used. Guide holder 3. Bolt 5.
At the desired distance...
Owners Manual - Page 13
...
NOTE:
• The workpiece will be sure that protrusion on the templet and move the tool with the templet guide sliding along the side of the templet guide 7. Templet
3
011852
Secure the templet to the dust nozzle.
011854
MAINTENANCE
1
1. Thumb screw 3. Trimmer base
011989
3 2
CAUTION: • Always be cut a slightly different size from...
Owners Manual - Page 14
... Makita Service Center. • Straight & groove forming bits • Edge forming bits • Laminate trimming bits • Straight guide assembly • Trimmer guide assembly • Trimmer base assembly...These accessories or attachments are required because of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have other accessories or ...
Parts Breakdown - Page 1
... 140739-4 39 941151-9 40 265792-0 41 227262-7 42 346392-6 43 163524-8 44 424396-9 45 941101-4
1-1/4 HP* Compact Router
Parts_Description
Qty
TOP COVER COMPLETE
1
CAUTION LABEL
1
RT0700C NAME PLATE
1
CONTRLLER
1
TAPPING SCREW 4X18
2
STRAIN RELIEF
1
TERMINAL BLOCK 2P
1
POWER SUPPLY CORD AWG#18- 1
CORD GUARD 8-85
1
BRUSH HOLDER CAP 5-8
2
CARBON BRUSH CB...
Parts Breakdown - Page 2
...STRAIGHT GUIDE ASSEMBLY
1
THUMB NUT M6
1
CAP SQUARE NECK BOLT M6X20 1
GUIDE PLATE
1
DUST NOZZLE SET
1
DUST NOZZLE SET
1
O RING 3
2
THUMB SCREW M4X19
1
THUMB SCREW M4X19
1
DUST NOZZLE SET
1
TEMPLET GUIDE 10
1
THUMB SCREW M4X19
1
TEMPLET GUIDE...
0
GRIP 36 COMPLETE
1
GUIDE HOLDER SET
1
THUMB NUT M6
1
ROD 8
2
CAP SQUARE NECK BOLT M6X20 1
TOOL BAG
1
OFFSET BASE SET
...
Flyer (English) - Page 1
... for improved performance
ACCURATE
Smooth rack-and-pinion fine depth adjustment system
COMFORT
Ergonomically designed body for increased comfort and control
DURABILITY
*Maximum horsepower
Models RT0700C RT0700CX3
Heavy duty aluminum motor housing for increased durability
PERFORMANCE & PRECISION. makitatools.com
Flyer (English) - Page 2
... n Tool bag (831327-5)
SPECIFICATIONS
Collet capacity
1/4"
No load speed
10,000 - 30,000 RPM
AMPS (115V)
6.5
Maximum horsepower*
1-1/4
Height
7-7/8"
Net weight
3.9 lbs. For a complete listing, please refer to the wall
STANDARD EQUIPMENT
RT0700C n 1/4" Collet (763637-1)
n Template guide 10mm (343577-5)
n 3/8" Collet (763619-3)
n Wrench 13mm (781039-9)
n Straight guide...
Similar Questions
Trying To Remove Motor On Makita Vc4710 Vacuum
cant find a service manual for this vacuum
cant find a service manual for this vacuum
(Posted by fishbowl8d 3 months ago)
I Have A 132386-5 Guide Assembly For Sharpening Knives Or Scissors.
Is there a manual on how to use it? For the makita 9820-2.
Is there a manual on how to use it? For the makita 9820-2.
(Posted by cgleith 10 years ago)
Hi Where Can I Purchase A Trimmer Guide For The Rt0700
Part011993 011844
(Posted by homeimprovements 10 years ago)
Tool Not Working
I bought a new makita LXPH01 Hammer Drill. I put a fully charged lit-ion battery 3.0a but when I pr...
I bought a new makita LXPH01 Hammer Drill. I put a fully charged lit-ion battery 3.0a but when I pr...
(Posted by shiki98 11 years ago)