Makita MAC5200 Support Question
Makita MAC5200 Support Question
Find answers below for this question about Makita MAC5200.Need a Makita MAC5200 manual? We have 2 online manuals for this item!
Question posted by jreaton80071 on May 22nd, 2014
Where Is The Serial Number Located\?
The person who posted this question about this Makita product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Makita MAC5200 Manual Pages
Owners Manual - Page 1
...Safety Guidelines and ALL instructions carefully before operating. OWNERS MANUAL FOR
Oil Lubricated Air Compressor
MODEL No MAC5200
SPECIFICATION CHART
Model # Horsepower SCFM @ 40 PSIG SCFM @ 90 PSIG Cut-In Pressure Cut-... Voltage -Single Phase Motor RPM Amperage @ max pressure Tank Size CSA/US Listed
MAC5200 3 6.9 6.5
110 PSI 140 PSI 47 mm 44 mm
120 3420 13.8 5.2 Gallon Yes
Minimum Circuit ...
Owners Manual - Page 2
TABLE OF CONTENTS
SAFETY INSTRUCTIONS 3 Warning Chart 3
GLOSSARY 7 DUTY CYCLE 7 GENERAL INFORMATION ON-RECEIPT INSPECTION 7 STORAGE 8 DESCRIPTION OF OPERATION 8 INSTALLATION and BREAK-IN PROCEDURES 9
Location Of the Air Compressor 9 Lubrication and Oil 9 Initial Start Up Procedure 10 Extension Cords 10 Piping 10 Grounding Instruction 10 OPERATING PROCEDURES 11 Daily Start-...
Owners Manual - Page 4
...
drain condensed water from the tank, causing rust and thinning of attachments.
Page 4 Risk of Attachments and Accessories Bursting
Exceeding the pressure rating of air tools, spray guns, air operated accessories, tires AND other components, which control tank pressure.
• Follow the equipment manufacturers recommendation and never exceed the maximum allowable...
Owners Manual - Page 5
...wellventilated area, free of gasoline or solvent vapors.
• If spraying flammable materials, locate compressor at least 20 feet away from spray area.
• Store flammable materials ...performed by electricity.
Work in a wet environment. Never operate the compressor in a secure location away from compressor.
• The compressed air from a breathing device connected to Breathing...
Owners Manual - Page 6
... turn the compressor off and bleed pressure from the air line before
maintenance while the
attempting any
attempt repair or
attachments before attempting maintenance, attaching tools or accessories.
Do not reach around protective shrouds or attempt maintenance until unit has been allowed to cool.
Risk from Compressed Air
The compressed air...
Owners Manual - Page 7
...Separate air transformers which the motor shuts off is supplied for operating paint spray guns, air tools, caulking guns, grease guns, air brushes, sandblaster, inflating tires or spraying weed killers, insecticides...Each air compressor outfit is off - If this
Page 7 protecting your accessory or air tool.
CUT-IN PRESSURE: While the motor is carefully tested and checked before the motor ...
Owners Manual - Page 8
...and into the compressor pump. PRESSURE SWITCH UNLOADING VALVE: The pressure switch unloading valve located on or run over). This filter must always be left unattended.
Protect the ... cord and air hose from obstructions. Store the air compressor in a clean and dry location. MOTOR THERMAL OVERLOAD PROTECTOR: The electric motor has a manual thermal overload protector. Turn pressure...
Owners Manual - Page 9
... "cut-in correctly. See "Operating Procedures".
INSTALLATION AND
BREAK-IN
PROCEDURES
LOCATION OF THE AIR COMPRESSOR Locate the air compressor in the tank. on the air requirements of air. SAFETY... excessive moisture. A small
Page 9 The air filter must be located at its factory set pressure (slightly higher than desired pressure. Serious damage will interfere with ...
Owners Manual - Page 11
... maximum pressure rating. 3. DANGER: Improper grounding can result in well-ventilated areas;
Remove the air tool or accessory. 9. grounding plug.
Do not use . Do not modify the plug that has been...release all local codes and ordinances. Note: If drain cock valve is ready for air tools and accessories. Page 11
Open the regulator by opening drain cock valve on bottom of ...
Owners Manual - Page 17
Serial No. Louis, MO 63126 (314) 909-9889
NEBRASKA
4129 S. 84th Street Omaha, NE 68127 (402) 597-2925
NEVADA... a letter to the outside of the Makita Factory Service Centers listed, or to one of the carton detailing the problem with your tool. FACTORY SERVICE CENTERS
1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS
ARIZONA
3707 E.
Date Purchased Dealer's Name and Address
Model No....
Owners Manual - Page 18
... by others;
• repairs are required because of normal wear and tear;
• the tool has been abused, misused or improperly maintained;
• alterations have other rights which vary from ... not apply to these chemicals are specially designed to one year period, return the COMPLETE tool, freight prepaid, to filter out microscopic particles. WARNING
Some dust created by power sanding,...
Owners Manual - Page 19
...Most favored points are appreciated.
1. LAST NAME/COMPANY NAME
MODEL NO. Facsimile Number (714) 522-8133
Page 19 MAIL THIS PORTION
Your answers to the following...
Radio
From Dealer
Exhibition
Newspaper
From Friend
Store Display
Previous Usage
Catalog
Other (
)
4. SERIAL NO. How did you learn about this portion by facsimile or mail. This product was purchased from:
Home...
Parts Breakdown - Page 1
...1 462009-E 1 458003-E 1
52
54 59
48
50 66
55
68
46
6 38 26
459002-E 1
40
353145-E 2
Makita Air Compressor - Model MAC5200
Part #
Qty
455015-E 2
181122-A 1
471151-E 1
9 10
35
62 4
5 15
23 24 25
18
21
33
28
53
72 71
64 ... assembly (1/4") Motor fan Unloading elbow Plug Manifold block Rubber cup Tool box lock Folding handle lock set (L&R) Tool box Wiring harness (motor -pr.
Similar Questions
Makita Mac5200 Where Us The Overload Switch Located?
(Posted by tmikestritch 1 year ago)
Makita Mac5200 Torque Specs
I need the torque values for the cylinder head on a Makita Mac5200 I followed the link on a previous...
I need the torque values for the cylinder head on a Makita Mac5200 I followed the link on a previous...
(Posted by markd3962 1 year ago)
Serial Number Location
I know this may seem like a dumb question, I just purchased a new ek7301 concrete cut off saw. I can...
I know this may seem like a dumb question, I just purchased a new ek7301 concrete cut off saw. I can...
(Posted by erikbogart 8 years ago)
Where Is The Reset Button Located On A 5200 Compressor
where is the reset button located on a 5200 compressor
where is the reset button located on a 5200 compressor
(Posted by jrkaval 8 years ago)
Where Is The Serial Number Located For A Mac5200 Compressor
(Posted by jreaton80071 9 years ago)