Makita HM1810 Support Question

Find answers below for this question about Makita HM1810.
Need a Makita HM1810 manual? We have 3 online manuals for this item!

Makita Overview Questions Manuals Reviews Videos Research

Question posted by bhconstruction on July 9th, 2021

Oil

where can you re- oil this unit and what type of oil is needed?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on July 9th, 2021 9:31 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,621,300

1,100
points

https://www.manualslib.com/products/Makita-Hm1810-274600.html

This tool does not require daily maintenance, but if the grease needs to be refilled it takes 60g/2oz of hammer grease part number A-90582. This is packaged in 1oz tubes. They also show oil and that part number is 181118-7. If you go to their site "makitausa.com" you can download or look at the section on maintenance and it shows you how to fill the reservoir.

https://www.fixya.com/support/t9572093-type_oil

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Makita HM1810 Manual Pages

Owners Manual - Page 2

... herein are connected and properly used for carrying, pulling or unplugging the power tool. Do not overreach. ENGLISH SPECIFICATIONS Model HM1801 HM1810 Blows per minute 1,100 1,100 Overall length 824 mm (32-1/2") 824 mm... your hair, clothing, and gloves away from heat, oil, sharp edges or moving parts. 15. Damaged or entangled cords increase the risk of inattention while ...

Owners Manual - Page 3

... proper warmup, hammering operation is below when using only identical replacement parts. Do not point the tool at no load. Take caution to the bit immediately after operation; Use the correct power tool for the particular type of parts and any one is difficult. 8. Check for which may cause serious personal injury. 3 If...

Owners Manual - Page 4

... be defective. Installing or removing the bit 002928 1. Bit without a collar on the tool. Insert the bit into the tool holder as far as it will go. V volts A amperes Hz hertz alternating or ...returns to the "OFF" position when released. Switch lever 1 CAUTION: • Before plugging in the tool, always check to see that the bit is switched ON, the carbon brushes may be worn out, ...

Owners Manual - Page 5

...follow the installation procedure in the holders. Screwdriver OPERATION Chipping/Scaling/Demolition Hold the tool firmly with more than the specified amount of operation. Cap 2. Wrench 23 ...brush is securely retained by yourself, proceed as it has a grease-packed lubrication system. Tool retainer shaft 1 3. Barrel 4. Keep the carbon brushes clean and free to contact the...

Owners Manual - Page 6

...period of injury to you need any other accessories or attachments might present a risk of ONE YEAR from state to one year period, return the COMPLETE tool, freight prepaid, to state... wrench • Wrench 23 EN0006-1 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Only...

Parts Breakdown - Page 3

... 6202, HM1211 SPUR GEAR 22, HM1800 WOODRUFF KEY 4, HM1810 BALL BEARING 6305LLB, HM1800 OIL SEAL 35, HM1800 O RING 61, HM1800 O RING 90, HM1500 CRANK SHAFT COMPLETE, HM1810 CRANK HOUSING, HM1810 CRANK HOUSING, HM1810 RUBBER PIN 4, HR2400 CRANK HOUSING CAP, HM1810 CRANK HOUSING CAP, HM1810 CAP COVER, HM1810 CAP COVER, HM1810 HELICAL GEAR 50, HM1800 BALL BEARING 6202, HM1211 H.S.H. BOLT...

Parts Breakdown - Page 4

...), HM1800 1 103 682547-2 CORD GUARD 15, HM1800 1 104 631670-0 PILOT LAMP, HM1810 1 105 638378-7 LEAD UNIT, HM1810 1 106 418951-7 LENS, HM1810 1 107 317901-8 REAR CASE, HM1810 1 108 922366-7 HEX SOCKET HEAD BOLT, HM1810 4 109 861399-6 NAME PLATE, HM1810 1 110 418954-1 TOP COVER, HM1810 1 111 419044-3 HANDLE SUB BASE, HM1800 1 115 687066-3 STRAIN RELIEF HM1800...

Flyer (English) - Page 1

... Level (107dB) and Vibration Reduces Operator Fatigue and Increases Productivity Equipped with Automatic Brush Cut-out System, Cylindrical Tool Holder and Warning Indicator Lamps to protect the motor RELIABILITY Model HM1810 Cylindrical tool holder allows greater serviceability should the original bolt holes become damaged ANTI-VIBRATION TECHNOLOGY BREAKER HAMMER PERFORMANCE ANTI-VIBRATION...

Flyer (English) - Page 2

... Equipment ■ Hex Wrench #5 (783203-8) Specifications Bit Type Blows per Minute (BPM) Impact Energy AMPS (120V) ...jobs ■ Lowest noise level in concrete One Piece Bushing Tool (751717-A) Removes excess concrete and roughens surface Other Accessories ....com, or call 1-800-4MAKITA or visit makitatools.com Model HM1810 Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 BREAKER ...