Home » LiftMaster » Garage Door Openers » LiftMaster TAC2C

LiftMaster TAC2C Support Question

Find answers below for this question about LiftMaster TAC2C.
Need a LiftMaster TAC2C manual? We have 2 online manuals for this item!

LiftMaster Overview Questions Manuals Reviews Videos Research

Question posted by schusterje on February 5th, 2014

I Am Replacing. Crown Jewel With 4 Wires To Connect To Relays (not 6). How Do I

How do I connect the 4 relay wires? The wiring diagram refers only to a 6 wire configuration. This is my first install and I can use some help. Thx

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related LiftMaster TAC2C Manual Pages

TAC2C Installation Manual - Page 1

... wires as shown. EXTERNAL KEYPAD RELAY 2 (no longer available) RELAY 1 AUTOCALL PHONE/TELCO EXIT (no longer available) Separate the Exit terminal block from the Autocall terminal block by sliding them from the Crown Jewel faceplate using the provided hex tool. 3 Slide the faceplate forward and rotate downward. 6.22" Speaker Microphone 1 23 456 789 *0# Keypad Call Button TAC2C...

TAC2C Installation Manual - Page 2

... PHONE/TELCO NEW TAC2C BOARD AUTOCALL 2 Press 2 to test Relay 2. 8 Connect the power wires to the ground screw in a secure location. The Master Code is used instead. 9 SET THE MASTER CODE Once power is applied, the unit will disconnect the call as soon as shown. For complete programming information refer to test Relay 1. Ground Wire Remove the PHONE...

TAC2C Programming Guide Manual - Page 1

Elmhurst, IL 60126-1196 www.liftmaster.com TAC2C & TAC2D TAC1 RETROFIT KIT FOR CROWN JEWEL & DOORKING 1812® SYSTEMS 1 23 456 789 *0# 1 23 456 789 *0# Programming Guide The Chamberlain Group 845 Larch Ave.

TAC2C Programming Guide Manual - Page 2

...: 0 6 3. Example: 0000 = 0.5 Seconds (Minimum) 0010 = 10 Seconds 8000 = 8000 Seconds (Maximum) 2 PROGRAMMING » KEYPAD NOTE: Use the STAR Key "*" to the house or complex. 1. Default level is 2. 1. Enter the Volume Level: 1 or 2 or 3 ADJUST RELAY OUTPUT TIME (RELAY 2) The amount of time (in success (indicated by double high success tone). Enter the Program...

TAC2C Programming Guide Manual - Page 3

... enter "*5" into the local telephone. The unit will activate simultaneously. Enter User Code to activate and latch relays 1 and 2. Enter the Program Code: 5 3 TRIGGER RELAY 1 1. Expires in 24 hours or after ﬁrst use. 1. ENGAGE PARTY MODE (RELAY 2) Party Mode will beep. 3. Enter the Master Code: ? ? ? ? 2. PROGRAMMING » KEYPAD CODE SETUP The unit's Master...

TAC2C Programming Guide Manual - Page 4

...Enter the command tone: 0 1 DISABLE CALL FORWARDING TELEPHONE COMMANDS FROM LOCAL TELEPHONE TRIGGER RELAY 1 Enter the command tone: 9 Enter the command tone: 0 2 FROM FORWARDED TELEPHONE ACCEPT CALL ...9 or 5 is pressed, the TAC2 will also disable the call forwarding mode. If 9 (relay 1) or 5 (relay 2) is not pressed. Enter the command tone: 5 ENABLE "DO NOT DISTURB" MODE Enter ...

TAC2C Programming Guide Manual - Page 5

...+ 51 + New Temporary (1 Shot) Code (4 digits) + Relay Associated with the User Code (1 or 2) (Expires after 24 ...REFERENCE KEYPAD PROGRAMMING PROGRAMMING NUMBER DESCRIPTION OF TASK FACTORY SETTING PROGRAMMING PROCEDURE 1 Trigger Relay One Master Code (4 digits) + 1 2 Trigger Relay... Code + 1 User Code + 2 ACTION Triggers Relay 1 Triggers Relay 2 AUDIO FEEDBACK FROM THE UNIT: 1 Low Tone Beep...

TAC2C Programming Guide Manual - Page 6

PROGRAMMING » QUICK REFERENCE TELEPHONE PROGRAMMING PROGRAMMING NUMBER **01 **02 **03 **06 **07 **#8 **10 **13 **14 **15 #*16 DESCRIPTION OF TASK Enable Call Forwarding Disable Call Forwarding Enable Intercom ...

TAC2C Programming Guide Manual - Page 7

PROGRAMMING NUMBER 0 *5 *9 DESCRIPTION OF TASK Accepts Call From The Unit (Also Extends Talk Time) Triggers Relay 2 Triggers Relay 1 FACTORY SETTING PROGRAMMING PROCEDURE 0 *5 *9 NOTE: Use the STAR Key "*" to disconnect. To use direct commands lift the handset, wait for 10 seconds. To control the gate press "*9" or "*5". Hang up to cancel any input. ANSWERING CALLS FROM...

TAC2C Programming Guide Manual - Page 8

... for changing the code setting or replacing the battery. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT... SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. Operation is subject to the following two conditions: (1) ...