Lexmark E260 Support Question
Lexmark E260 Support Question
Find answers below for this question about Lexmark E260.Need a Lexmark E260 manual? We have 5 online manuals for this item!
Question posted by isda on October 20th, 2014
How To Reset Counter Lexmark E260 Counter?
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by waelsaidani1 on October 20th, 2014 6:32 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Hello follow instructions here: http://support.lexmark.com/index?page=content&id=HO3483&locale=en&userlocale=EN_US
Related Lexmark E260 Manual Pages
Service Manual - Page 16
... personnel. Connector locations uses illustrations to prevent
problems.
7.
xvi Lexmark™ E260, E260d, E260dn Special tools and test equipment, as well as...perform the task. 4513-200, -220, -230
Preface
This manual contains maintenance procedures for making printer adjustments and removing and installing
FRUs.
5. Warning: A warning identifies something that might cause a ...
Service Manual - Page 17
General information
The Lexmark™ E260, E260d, and E260dn are monochrome laser printers designed for more information. See "Repair information" on E260, E260d and E260dn. General information 1-1 This book contains information on page 4-1 to determine the symptom and repair the failure. Maintenance approach
The diagnostic information in ...
Service Manual - Page 24
... Guide available on the 250-sheet tray before pushing the tray into the printer.
• Make sure paper guides are positioned before loading it. Make ...Needle nose pliers • Volt-ohmmeter • #1 and #2 Phillips screwdriver • Slotted screwdriver
1-8 Lexmark™ E260, E260d, E260dn
Contain windows, holes, perforations, cutouts, or embossments - Are stuck together - Have any...
Service Manual - Page 28
... button
Ready light
Continue button
Power-On Self Test (POST) sequence
When the printer is a problem in the printer such as a paper jam, then the panel lights indicate the problem. The printer cycles down into standby mode, and lights solid.
2-2 Lexmark™ E260, E260d, E260dn Check for more information.
5. 4513-200, -220, -230
Overview of...
Service Manual - Page 30
...Unsupported Flash Option Installed
Cancel job
10
Reset printer
Restore factory defaults
Invalid engine code
11
Invalid network code
Resolution reduced while
11
&#...13
Printer error³
13
2-4 Lexmark™ E260, E260d, E260dn
Service Manual - Page 32
...220, -230
Common light sequences when replacing the photoconductor
Printer Condition
Page
Replace photoconductor
12
(printer hard stop)
Ready and Replace Photoconductor/Power Save and Replace...
x
2 -6 Lexmark™ E260, E260d, E260dn
Service Manual - Page 34
... users can use Hex Trace to help troubleshoot printing problems. After resolving the problem, turn off the printer to reset the printer. Wait for the message to clear.
• Press and hold Cancel to reset the printer.
2-8 Lexmark™ E260, E260d, E260dn The Ready light is waiting until a print timeout occurs, or until it receives additional data...
Service Manual - Page 36
Insufficient collation area/Insufficient memory
Meaning
The printer memory is resetting to clear.
2-10 Lexmark™ E260, E260d, E260dn
Any active print jobs are canceled. The printer will automatically reset. Action
• Press and release Continue to clear the message and continue printing the job. (The job may not print correctly.)
• Press and ...
Service Manual - Page 38
.... • Replace the photoconductor kit.
Action
• Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit.
2-12 Lexmark™ E260, E260d, E260dn The printer will not print any more pages until the photoconductor kit is Off. Note: The Toner Alarm must be replaced. Photoconductor kit life warning...
Service Manual - Page 40
.... Remove paper from the paper path. 4513-200, -220, -230
Paper jam printer error (2xx)
Meaning
The printer has a paper jam. Action
• Remove printed pages from the output bin. • Press Continue to reset the printer.
2-14 Lexmark™ E260, E260d, E260dn Action
• Press Continue twice quickly to see the secondary error...
Service Manual - Page 42
... both on, a paper jam has occurred with a
Printer Condition
Page
200: Paper jam at the input
18
...61548;
2-16 Lexmark™ E260, E260d, E260dn
Common light sequences for help. The following table shows what these light sequences mean and where to display the secondary error code...
Service Manual - Page 44
...input sensor, which can be either after the print media leaves the tray and enters the printer or in the fuser area under the toner cartridge assembly.
Action
Open the front door, ...occurred at the duplex sensor, but did leave the printer exit sensor.
The jammed media is exiting the printer. Action
Open the rear door, and clear the paper jam.
2-18 Lexmark™ E260, E260d, E260dn
Service Manual - Page 48
... or graphics on the page and deleting unnecessary downloaded fonts or macros.
• Install additional printer memory.
2-22 Lexmark™ E260, E260d, E260dn Insufficient defrag memory
Meaning
The printer memory does not have enough memory to reset the printer.
This may not print correctly.) • Press and release Cancel to cancel the print...
Service Manual - Page 56
... is performed which allows the printer to perform the task.
Note: All service errors are initially communicated by paper
port device
906: Service engine software error
Service watchdog: 90x
901: Timer service slow
2-30 Lexmark™ E260, E260d, E260dn Unplug the...
Service Manual - Page 72
... detected by the specified device
983.xx Invalid command received by the specified device
2-46 Lexmark™ E260, E260d, E260dn If this does not resolve the problem, then replace the firmware card ...secret failure
959.23 959.24
Pensive self test failed during HW prog
959.26 Incremental counter reset exceeds maximum value
959.27 Increment count failed due to max value limit
959.28 Invalid...
Service Manual - Page 74
...Wait Timeout Auto Continue Jam Recovery Page Protect Print Area
Job Menu Cancel Job Reset Printer Print Buffer
Quality Menu Print Resolution Toner Darkness PictureGrade™
PPDS Menu Orientation ... Mode USB Buffer Mac Binary PS
2-48 Lexmark™ E260, E260d, E260dn These are accessed through the driver.
4513-200, -220, -230
Diagram of the printer menus
Not all menus or selections will be...
Service Manual - Page 86
... a new PC Kit. Check the springs in the printer driver. Replace the transfer roll assembly if the springs ...laser light path is low, then try a new one. Check to evenly distribute the toner.
Place a sheet of wear, damage, or contamination. A heavier media may have an unbalanced force against the PC (photoconductor) drum. Variation in the printer driver.
2-60 Lexmark™ E260...
Service Manual - Page 88
...Vertical or horizontal streaks appear on page 2-61. Vertical white lines may be caused by the laser beam, which may be partially blocked. Check those settings.
Vertical white lines may be caused by...the fuser at the end of the page. With the printer off , clear the path or clean the lens. Replace the PC kit.
2-62 Lexmark™ E260, E260d, E260dn
4513-200, -220, -230
Solving ...
Service Manual - Page 96
... printer. 2. Turn off the printer.
Off (default) On
Help isolate print quality problems, such as streaking. Return the photoconductor counter to factory default values. 4513-200, -220, -230
Configuration menu selections
To enter the Configuration menu:
1. The replace photoconductor message should be cleared only when the photoconductor kit has been replaced.
3-4 Lexmark™ E260...
Service Manual - Page 176
...Reset Factory Defaults 3-4 reset maintenance page counter 3-4 Reset PC Counter 3-4
S
safety information xiii safety inspection guide 6-1 service checks 2-51
controller card 2-51 cooling fan 2-52 cover interlock switch 2-52 dead machine 2-53 fuser 2-53 LVPS/HVPS 2-54 main motor 2-54 operator panel 2-55
I-2 Lexmark™ E260...2-1 symptom tables 2-49
POST 2-49 printer 2-50
T
test pages Print Quality ...
Similar Questions
How To Reset Counter After Maintenance Kit On A Lexmark T652
(Posted by Do195 9 years ago)
Resetting Counter For Pckit
After replacing pckit on lexmark 460dn, how to reset counter on control panel?
After replacing pckit on lexmark 460dn, how to reset counter on control panel?
(Posted by geosue333 12 years ago)