LG WM2496HWM Support Question
LG WM2496HWM Support Question
Find answers below for this question about LG WM2496HWM.Need a LG WM2496HWM manual? We have 1 online manual for this item!
Question posted by gt2825 on October 2nd, 2018
Need Pump Wiring Connections Help
I removed the drain pump and did not document the wiring.Pump has two wires black and brown to which connections on pump motor?Other end of drain pump also has two connections black and blue to which connections?Any help would be appreciated!
Current Answers
Answer #1: Posted by hzplj9 on October 3rd, 2018 12:56 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
I would assume from the colours that the blue and brown are the live supply to the pump. The other two could be a sensor switch to control the motor. If you have a multi meter you can use this to identify if the blue and brown are live. Take all precautions to prevent a shock. In the US you have 120v but in Europe we have 240v. The other 2 wires can be traced back through the machine to the control board. Check also if they have a high voltage across them the same as the blue and brown. If you have little success then please post another question and give us photos of the wires and motor to enable us to give you a more suitable answer.
Good luck.
Related LG WM2496HWM Manual Pages
Owner's Manual - Page 3
...
Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley. The jets spray and help tumble clothes to Use the Washer...14 Maintenance ...17 Troubleshooting Guide ...20 ... for selected cycles. Built-in your washer and/or dryer. Using the RLM (Remote Laundry Monitor) The RLM monitors status of the laundry. Tilted Drum and Extra Large Door Opening...
Owner's Manual - Page 4
...of malfunction or breakdown, grounding will be grounded. WARNING: Improper connection of the equipment-grounding conductor can result in the washer. IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USE
! These ... water flow from service or discarded, remove the door to catch fire.
• Do not use an adapter or extension cord. • Do not remove ground prong. • If you ...
Owner's Manual - Page 5
Accessories
for removing shipping bolts and leveling the washer
4 SPECIFICATIONS
Door Seal
Safety Cover (PLC Modem)
Name:
Front-loading Washing Machine
Power supply:
120V~ 60Hz
Size:
68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.1 cm (D ...
Owner's Manual - Page 6
In countries where there are areas which may be need to keeping the appliance and its surroundings in clean condition at all times.
Removing shipping bolts
cap
1. Close the holes with the ...slightly. To reduce the risk of electric shock, do not install the washer in the middle of the washer to remove easily. Damage caused by cockroaches or other vermin, pay particular attention to ...
Owner's Manual - Page 7
... minimum spacing allowed. The following dimensions shown are not recommended.
• Never install the washer on all sides of
the washer is recommended. If the floor is wood and/or frame construction, you may need to a front-loading washer than top-loaders, causing greater vibration.
If your floor is not solid, your house. You...
Owner's Manual - Page 8
...the electronic control unit may occur.
Any of this laundry product. Protect the power cord from physical or mechanical...dangerous. Old hoses should be installed.
• Two Sealing washers are connected to avoid a hazard. • If the machine will ...outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are not guaranteed to product or property will not be...
Owner's Manual - Page 9
...
• Place the end of the drain hose in the hole of the floor drain system.
• The drain hose should not be dangerous for children.
When disposing of the appliance, cut off the faucet if the machine is a risk of the washer.
• Properly securing the drain hose will protect the floor from damage due...
Owner's Manual - Page 10
... top plate diagonally, the machine should not move up against of the base of laundry in adjustment.
ENGLISH
INSTALLATION INSTRUCTIONS
Level adjustment
Tighten
Tighten
• Leveling the washing ... adjust the feet perfectly. If not, adjust the feet accordingly.
• If you install the washer and dryer with pedestals, it is spinning with a load. Then, press POWER, RINSE+SPIN, ...
Owner's Manual - Page 11
... may cause an out-of soil. The washer can be washed in water onto stains like... items with lightly soiled ones. Different fabrics need to be washed separately.
• Check... and keys can occur causing discoloration of the washer should be more than half the total wash load... as dye and lint transfer can damage both your washer and your clothes. Wash lint producers and lint collectors...
Owner's Manual - Page 12
...laundry products. After loading the laundry additives into the appropriate compartments. 3.
NOTE : Liquid detergent will automatically be dispensed at the end of the cycle. The detergent will drain into the washer... make less suds, improve washing and rinsing performance, and help to keep the interior of your LG TROMM washer clean. For the best washing and rinsing performance, low-...
Owner's Manual - Page 13
...the maximum fill line.
• For powered detergent, remove both the liquid detergent box and insert.
• ... will not dispense with the same type of the cycle. NOTE: Do not place, store, or spill laundry products (soap, detergent, bleach, softener, etc.) on the wash load.
• The fabric softener will...; Add recommended amount of your washer or dryer.
USING THE DISPENSER
2.
Owner's Manual - Page 15
... before Start. Delay
• Allows the start /stop the washer. HOW TO USE THE WASHER
Option
1.
NOTE: This front load washer requires longer cycle time and gets clothes much cleaner, yet is....
2. Cycles
• Rotate the Cycle selector knob to start of selecting a cycle, the washer automatically turns off.
4. Power
• Use this button to select cycle designed for small loads...
Owner's Manual - Page 16
... Custom program is on the cold water at your faucet.
• This washer automatically adjusts the water level for the type and size of the Beeper.
15... Cold rinse temperatures depend on .
9. Beeper
• Press repeatedly to cycle through available options.
• To start Drain/Spin cycle: 1. Press Start/Pause button.
8. Soil Level
• To change the spin speed, press the Spin...
Owner's Manual - Page 17
... the washer. Press and hold the Stain Cycle button for 3 seconds to indicate that need pretreatment....ended, open when
is too high, the
door cannot be unlocked by a power failure.
7. Stain cycle
• Adds more time to the wash and rinse cycles for better stain removal...the cycle the washer is locked. • The door can lead to ensure the removal of the washer is operating.
...
Owner's Manual - Page 18
... is hot.
• Allow the water to cool down before opening the pump filter to the left in the laundry. Turn the drain plug ( ) to the original place. After cleaning, turn the
pump filter open to remove objects. ENGLISH
MAINTENANCE
Before cleaning the washer interior, unplug the electrical power cord to prevent water from flowing onto...
Owner's Manual - Page 19
Wrinkling, color transfer, and odors may need to be cleaned periodically due to laundry additive build-up in places where it cannot be seen and it is not easily removed from the washer before doing a load of scale clogs appliances, and if it is not kept in check, these will drain into the tub. Over time...
Owner's Manual - Page 20
... washer.
3. Do not add laundry.
19 Exterior Proper care of the machine can extend its life. Try not to the bleach compartment. Open the dispenser drawer and add liquid chlorine bleach to damage the surface with a damp cloth. NOTE: Remove hard water deposits using detergent. Turn off any water in an upright position. 9. Drain...
Owner's Manual - Page 21
...washer.
• House drain pipes are in firm contact with the floor, while the washer is in the drum.
• Are all , check the following points before you call for removing shipping bolts. Contact plumber if necessary. Check another tap in drum or pump... washer is restarted, call the Service Department.
Stop washer and rearrange wash load. Water leaks
• Fill hose connection ...
Owner's Manual - Page 22
... laundry, water pressure, water temperature, and other using Drain/Spin cycle. (The door may be increased. Drain the water by pressing the Start/Pause button to wipe around and under the door seal frequently. Clicking: When the door is circulated. -
Washer does not start
• Electrical power cord may not be plugged in or connection...
Owner's Manual - Page 23
... due to the faulty water valve.
• The water level sensor malfunction.
• Overload in motor.
• The washer experienced a power failure. Restart the cycle.
22
Clean the drain filter.
• Load is too small. • Load is clogged. Rearrange load to help balance the load. Close the water tap.
Clean and straighten the...
LG Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
NetCast Network Install and Troubleshooting - LG Consumer Knowledge Base
... connection may take a moment to open . Activating from your router (or other companies do I remove ... three of these , but you need help with the settings found and type ...that convert a wired connection into your router and test it to a bad physical connection. If your ...from the player if applicable. Note: This document doesn't discuss the My Media application. Sometimes... -
NetCast Network Install and Troubleshooting - LG Consumer Knowledge Base
... TVs don't have successfully tested these are items you help with the manual function. It will inform you need a software connection, which is in the the NetCast menu and choose activate...document below for the TV is the actual cable connection to let the TV join the network. If the Quick Setup doesn't work . You can use a power line adapter that convert a wired connection... -
LG Front Load Washer: General FAQ - LG Consumer Knowledge Base
...washers that when loading the washer to match your washer. The WDP2W is selected then press start. Both WDP3 and WDP4 models are not cleaned up to connect...remove any items that the washer drum is not visible during a running cycle to top Units with the manual drain hose, then remove the drain pump..., and laundry additives can I put in the washer? 17. The drain pump filter (located...
Similar Questions
Oe Error And Drain Pump Grinds
Washer stopped during wash cycle, displayed OE error. Drained tub, cleaned drain filter. When washer...
Washer stopped during wash cycle, displayed OE error. Drained tub, cleaned drain filter. When washer...
(Posted by gt2825 5 years ago)
Washer Has Water Left In It And A Code Oe Comes Out
model # wm2496hwm I have cleaned out the filter screen and drained all water from washer but when us...
model # wm2496hwm I have cleaned out the filter screen and drained all water from washer but when us...
(Posted by am2submaker 12 years ago)