Kenwood KAC X40 Support Question
Kenwood KAC X40 Support Question
Find answers below for this question about Kenwood KAC X40 - eXcelon Amplifier.Need a Kenwood KAC X40 manual? We have 1 online manual for this item!
Question posted by SANDYBULLARD55 on January 29th, 2011
Pcon Connection
What is the pcon connection for on a kenwood kac-x40 amp. where does it connect?
Current Answers
Related Kenwood KAC X40 Manual Pages
Instruction Manual - Page 1
... space provided below. Refer to read through this instruction manual.
Model KAC-X40 Serial number
US Residence Only
Register Online
Register your Kenwood dealer for information or service on the warranty card, and in the spaces designated on the product. KAC-X40
FOUR CHANNEL POWER AMPLIFIER 7 page 2-7
INSTRUCTION MANUAL
AMPLIFICATEUR 4 CANAUX 7 page 8-13
MODE D'EMPLOI
AMPLIFICADOR...
Instruction Manual - Page 2
...dampened by using
Grommets. • Connect the ground wire to a metal part of the car chassis that acts as damage. •...speakers when the engine is running,
connect a line noise filter (optional) to each amplifier. FCC NOTE
This equipment has been...cause your Kenwood dealer. FCC WARNING
This equipment may cause harmful interference unless the modifications are going to be connected should ...
Instruction Manual - Page 3
...
• Install this
order. 6.Install the installation fittings in the unit. 7.Attach the unit. 8.Connect the negative - Otherwise heat build-up occurs and the unit may cause injury or an accident. ...that there is nothing hazardous on top of the unit.
• The surface temperature of the amplifier will not obstruct driving. Self-tapping screw (ø5 × 18 mm)
Installation board, etc...
Instruction Manual - Page 4
...'s positive terminal. Do not remove caps from unconnected wires or connectors to prevent short circuits.
• Connect the speaker wires to turn the power off before changing the setting of any switch.
• If ...blows, check wires for shorts, then replace the fuse with one of the car can cause this unit to fail.
• After installation, check that no unconnected wires or connectors are touching...
Instruction Manual - Page 6
... cover to access to its controls for each channel. • Bridged Connections: When you wish to use the unit as a high-output monaural amplifier, bridged connections are to be connected should have an impedance of the signals to be used as a stereo amplifier, stereo connections are to connect it with a large variety of systems by which the low frequency...
Instruction Manual - Page 7
... The input sensitivity adjusting control is not set improperly. SOLUTION • Connect the input (or output) cables. • Check connections by a screw in your unit may just be set to the correct...speakers wire are connected with wrong + /-polarity.
• A speaker wire is too small (or too large).
Troubleshooting Guide
What might appear to be a malfunction in the car body.
•...
Similar Questions
I Have A Kenwood Excelon Kac-x20 Amp When It's Hooked Up An U Like Turn Switch
OK I got a kenwood excelon KAC-X20 amp an u first hook it up or if it was hooked up if u first turn ...
OK I got a kenwood excelon KAC-X20 amp an u first hook it up or if it was hooked up if u first turn ...
(Posted by ottjones91 1 year ago)
Amplifier Sound Cutting
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
(Posted by marksuzyo07 7 years ago)
No Power To Kac-6104d Amp
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
(Posted by jwilliams644508 10 years ago)
What Year Was The Kenwood Kac-x621 Amp Made
(Posted by outlawstreetrace 11 years ago)
