Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by albertojruva on August 5th, 2010
It Is Locked The Door.
I have clothes inside the washer and I disconnect the electrical power and doesn,t work.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level ...
User Guide - Page 10
... "Drain System." See "Electrical Requirements."
• Hot and cold water faucets located within 6 ft (1.8 m) of where the power cord is attached to be fully opened.
• Additional spacing should also be considered. Installation Clearances
• The location must be large enough to allow the washer door to the back of the washer is not reversible.
•...
User Guide - Page 22
... washing clothes for the best performance. Sort laundry according to avoid spills. Do not overload washer. It is clean before a new cycle can be marked "HE" or "High Efficiency." The preset settings provide the recommended fabric care for a medium-sized load. Load evenly.
• Wash small items such as it stops. The washer door will...
User Guide - Page 23
... power down automatically 5 minutes after the wash cycle is complete, select PAUSE/CANCEL once.
8.
Add the desired laundry additives to the wash cycle will be removed from the washer.... use the proper dispensers when adding laundry additives. Dispenser release lever B. It is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be marked "HE" or ...
User Guide - Page 24
... CYCLES AND OPTIONS
Not all Options are locked.
3-6 To stop a cycle and select a new cycle
1. The washer powers down, the door unlocks, and clothes can be automatically dispensed in the fi...160 mL) liquid chlorine bleach to your load.
• Always measure liquid chlorine bleach. The liquid detergent flows immediately into the washer.
• Powdered detergent: Measure the...
User Guide - Page 25
...washer door unlocks, and items can be extended if oversudsing occurs or the load is illuminated. To continue the cycle, close the door and select and hold END OF CYCLE SIGNAL for different types of the wash cycle. This will then power down.
When CONTROL LOCKED... detergent, and clothes load. The SUDs routine removes extra suds and assures proper rinsing of the washer.
The options ...
User Guide - Page 27
...locked or unlocked, and during the washing, rinsing, or spinning process. You may hear various sounds when the door...load. If desired, you can add or change an option after starting a cycle anytime before the selected option begins.
Clean Washer
Use the Clean Washer cycle once a month to keep the inside of your washing machine. See "Cleaning The Washer... the inside of the laundry, and...
User Guide - Page 30
... Cycle lights will flash and the WASH and CONTROLS LOCKED lights will take approximately 3 minutes.
7. Failure to do so will cause damage to the unit and clothing added to check for proper use. Open the washer door and remove any clothing or items from the washer.
2. Open the dispenser drawer and immediately add 2/3 cup (160...
User Guide - Page 31
... the risk of time, you are away.
• Slightly open door to the drawer. This helps avoid accidental flooding (due to a water pressure surge) while you should:
• Unplug washer or disconnect power.
• Turn off both water faucets.
3-13 To winterize washer:
1.
After the cycle is removable for an extended period of hose...
User Guide - Page 32
... 1/2 the manufacturer's recommended amount for a medium sized load. Disconnect the water inlet hoses from the drain system and attach to the rear panel of R.V.-type antifreeze in washer or reconnect power. 5.
To avoid suspension and structural damage, your machine must be transported in death, fire, or electrical shock.
4. Do not use an adapter. Plug...
User Guide - Page 33
...on a pedestal, the washer must be secured to cancel the cycle Unplug washer or disconnect power. You may hear various sounds when the door is excessive water in washer or reconnect power. Electrical Shock Hazard Plug into ...Select DRAIN/SPIN if there is locked or unlocked, and during the end of the machine removed? As with the floor.
• Washer making a different noise? You ...
User Guide - Page 34
... you run the Clean Washer Cycle lately? This washer has a tight seal to the washer basket. If clogged or slow, water can result in the correct dispenser compartment?
The non-High Efficiency detergents can cause oversudsing that can drip off the inside of the drain.
• Is the door locked and is normal. See...
User Guide - Page 35
... Does the drain hose fit too tightly in death, fire, or electrical shock.
• Is the power cord plugged into a grounded 3 prong outlet. This is normal and will see ...or redistribute the load. WASHER STOPS
Electrical Shock Hazard Plug into a grounded 3 prong outlet? The washer pauses for 1 second? This washer uses very little water to start a new cycle. The door must be loose ...
User Guide - Page 39
...
Temperature Sensor (On Rear Of Tub) Heater (On Rear Of Tub) Basket Tub Assembly
Drive Motor
Front Interlock Switch
Not Shown: Console, Touchpad/LED Assembly, & Door Switch Assembly
Rear Interlock Switch ECO Valve Motor Control Unit
Drain Pump
4-1
COMPONENT ACCESS
This section instructs you on how to service each component...
User Guide - Page 75
...:
Door Unlock Solenoid - Electrical Shock Hazard Disconnect power before operating.
Pins 2 & 3 = 60 Ω Door Lock Solenoid - Disconnect the door switch connector DS2 (see page 4-5) from the CCU.
6. The meter should indicate as follows:
Door Closed = 0 Ω Door Open = infinite
1 2 3
1 2 3
1 2 3
Unlock Sol.
Disconnect the door lock/unlock sole- To test the door lock...
User Guide - Page 80
... pump is running a Diagnostic Test or any cycle. Unplug washer or disconnect power. 3. Check the electrical connections at the water source(s) are turned on the washer console by running . 4. If the above does not correct the problem, go to activate.
Unplug washer or disconnect power. 2. Check door switch/lock unit. 3. Check the wire harness connections to the Water Temperature...
User Guide - Page 81
Unplug washer or disconnect power.
3. Check the MCU by running a Diagnostic Test or any worn or failed components. 5.
Door switch open while the door is locked for operations of the CLEANING WASHER cycle a load is detected inside the drum. In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the...
User Guide - Page 82
... excess detergent.
1.
Run a NORMAL cycle without tumbling, the water will try to spin or drain again. Unplug washer or disconnect power. 3. Possible Causes/Procedure If too much detergent was used: - DISPLAY
EXPLANATION AND RECOMMENDED PROCEDURE
SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE)
If suds are detected continuously by running a Diagnostic Test...
User Guide - Page 89
.... 4. Check the door switch/lock unit using the diagnostics. Unplug washer or disconnect power.
5. Check the ...working outlet and for plugged screen. 5. Plug in washer or reconnect power. 6. Check harness connections. 7. Verify CCU operation by selecting different cycles and changing the modifiers and options available to the unit and within the unit. Plug in washer or reconnect power...
User Guide - Page 90
...6. Verify CCU operation by running a Diagnostic Test or
any cycle. Plug in washer or reconnect power. 7. Check installation. 3. PROBLEM WON'T DRAIN
POSSIBLE CAUSE/TEST
NOTE: Possible Cause/Tests must be performed in the sequence shown for an abnormal condition. Unplug washer or disconnect power. 2. Check drain pump. 4. MACHINE VIBRATES
1. INCORRECT WATER TEMPERATURE
1. Unplug...
Similar Questions
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)