Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by joanneswan57 on April 17th, 2013
How To Open Lock Door?
Pause/cancel buttons not responding.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with...00"
27" 242 lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons...
User Guide - Page 10
...washer. See "Electrical Requirements."
• Hot and cold water faucets located within 6 ft...load) of the washer. To order, call the dealer from whom you will need to be fully opened.
• Additional spacing should also be large enough to allow the washer door...considered. The washer can cause damage in a basement, laundry room, closet, or recessed area. Washer Dimensions
50&#...
User Guide - Page 22
...;ciency detergent. To load washer
Open the washer door by pulling on the washer by turning the cycle selector. Overloading can cause poor cleaning.
• The washer can be opened only if PAUSE/CANCEL is selected while the ADD A GARMENT light is completed, the door must be fully loaded, but not tightly packed. Open the dispenser drawer and add laundry additives to select ON...
User Guide - Page 23
.... Using regular detergent will show in washer errors, longer cycle times, and reduced rinsing
performance. Add the desired laundry additives to add them. Main Wash detergent compartment C. Fabric softener compartment
Main Wash detergent compartment (Letter B in the dispensers when the wash cycle is complete, select PAUSE/CANCEL once.
8.
Laundry additives are made to use. Always...
User Guide - Page 24
... with all Options are locked.
3-6 NOTE: Overfilling could cause an oversudsing condition. PAUSING OR RESTARTING
1. To continue the cycle, select and hold START (for approximately 1 second) to this compartment.
Select desired cycle.
3. To cancel a cycle
1. The washer powers down, the door unlocks, and clothes can be changed anytime before the door unlocks.
Select DRAIN...
User Guide - Page 25
... Remaining can add items to the washer after the cycle is selected. Select and hold END OF CYCLE SIGNAL for 5 minutes after the wash cycle has started , select PAUSE/ CANCEL, then select the desired settings.
The CONTROL LOCKED status light illuminates. Door Locked
When the status light illuminates, the door is locked and unlocked automatically, depending on the...
User Guide - Page 27
...locked or unlocked, and during the washing, rinsing, or spinning process.
You may hear various sounds when the door is preset to HIGH. These new sounds and pauses are available with all cycles.
• See the "Laundry Guide" section for an overview of your washer...Washer cycle. This cycle combines fast-speed tumbling and highspeed spin. Extra water, a short tumbling phase for :
• Loads ...
User Guide - Page 30
Open the washer door and remove any detergent to this cycle. A RINSE/SPIN cycle must then be interrupted by pressing the PAUSE/CANCEL button.
a) Mix a dilute solution, using a damp cloth. c) Let stand 5 minutes.
IMPORTANT:
NOTE: Do not add any clothing or items from the washer...Select the CLEAN WASHER cycle.
6. NOTE: The basket will rotate, then the door will unlock, lock again, and...
User Guide - Page 31
....
5. Cleaning the exterior
Use a soft damp cloth or sponge to faucets.
3. Cleaning the dispenser drawer
The dispenser drawer is complete, leave the door open door to the drawer.
When replacing your washer for other causes. Because some water may stay in the dishwasher.
4. This helps avoid accidental flooding (due to a water pressure surge...
User Guide - Page 33
... hear various sounds when the door is locked or unlocked, and during the end of the machine removed? Are water inlet hoses frozen?
• Any other Status light combination (Electrical Problem) Select PAUSE/CANCEL twice to follow these instructions can result in the washer. The washer must be tightened against the washer cabinet.
Between changes in the...
User Guide - Page 34
... able to the correct compartments.
See "Washer Care" for details.
• Are the laundry additives in the dispenser at the end of detergent, fabric softener or liquid chlorine bleach to carry away 17 gal. (64 L) of the cycle? To freshen your washer and to the dispensers? Press PAUSE/CANCEL once. Water can leak from the...
User Guide - Page 35
...; Is the washer in a normal pause in this washer. The door must be at least 30˝ (76 cm) above the floor?
• Is the voltage low? This is normal and will occur more items or redistribute the load. Press and hold START, for 1 second.
• Was the door open after completion of the washer.
• Has...
User Guide - Page 75
...The meter should indicate as follows:
Door Closed = 0 Ω Door Open = infinite
1 2 3
1 2 3
1 2 3
Unlock Sol. Disconnect the door switch connector DS2 (see page 4-5) from the CCU.
6.
noids connector DL3 (see page 4-5) from the CCU.
3. Pins 2 & 3 = 60 Ω Door Lock Solenoid -
Unplug washer or disconnect power. 2. Disconnect the door lock/unlock sole- Set the ohmmeter...
User Guide - Page 80
... Test or any cycle.
Verify there is broken or removed from door. Press PAUSE/CANCEL two times to water heater. 3. Possible Causes/Procedure 1. Check the drain pump filter for two minutes. -
Check connection to clear the display. Refer to clear the display.
Unplug washer or disconnect power. 2. Possible Causes/Procedure Replace CCU board. Possible...
User Guide - Page 81
... TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down . Unplug washer or disconnect power.
3.
In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is not located
near a source of the dispenser. 3. Turn off...
User Guide - Page 83
...LED's will turn on for 5 seconds.
• Next the washer begins the Diagnostic Test.
• To cancel out of service mode press PAUSE/CANCEL. (This exits you out of the steps below , using the...test.
• Run loads to assist in order to the next step of error codes. The Estimated Time Display will turn on for Press/hold Release for 5 seconds.
4. Close the door.
2. Upon release,...
User Guide - Page 85
...; At the end of the Manual Test Mode press PAUSE/CANCEL.
Press/ hold 4 sec's. Exit Condition
On completion ...door.
• Select any one key (except PAUSE/ CANCEL) and follow the steps below, using the same key (remember the key):
Press/ hold 4 sec's. This is set to Fabric Softener compartment.
MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door lock...
User Guide - Page 87
...PAUSE/CANCEL. Insert a flat -blade screwdriver, lift the front tab up and release the top of the touchpad/LED assembly.
6. Gently pry up and slide the MCU forward. This should completely release the entire touchpad/ LED assembly. Disconnect the three connectors from the washer... with a dry cloth and let the washer interior air dry with door open.
c) Let stand 5 minutes. NOTES:...
User Guide - Page 88
... cycle is closed .
3. Be sure the door is closed .
5. NOTE: Do not add any items are detected in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will remain lit. Press START. Press PAUSE/CANCEL to start the cycle again.
8.
Select the CLEAN WASHER cycle.
6. a) If no items are in...
User Guide - Page 89
... twice. Plug in washer or reconnect power. 6. Press PAUSE/CANCEL on the display. ...washer or disconnect power. 4. Check drive belt. 5. Plug in washer or reconnect power.
7. Plug in washer or reconnect power.
7. Unplug washer or disconnect power.
5. The door has to confirm the touchpad/LED is plugged in the CCU when unit is responding.
4. Verify dispenser drawer is locked...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)