Kenmore 16677 Support Question
Kenmore 16677 Support Question
Find answers below for this question about Kenmore 16677 - Serger Sewing Machine.Need a Kenmore 16677 manual? We have 1 online manual for this item!
Current Answers
Related Kenmore 16677 Manual Pages
Service Manual - Page 2
... THE MACHINE SOCKET
7
TO ADJUST THE NEEDLE HEIGHT
8
TO ADJUST THE PRESSER BAR HEIGHT
9
TO ADJUST THE FEED DOG HEIGHT
10
TO ADJUST THE TIMING OF THE NEEDLE AND THE FEED DOG
11
TO ADJUST THE TIMING OF THE NEEDLE AND THE UPPER KNIFE
12
TO ADJUST THE HEIGHT OF THE LOWER LOOPER...
Service Manual - Page 6
... FRONT COVER UNIT WITH SETSCREWS (B), (C), (D) AND (E). 5. TURN THE HAND WHEEL TOWARD YOU TO SET THE UPPER LOOPER AT ITS LOWEST
POSITION. FRONT COVER UNIT
SETSCREW (B)
S
J /
UPPER LOOPER_
SHOULD BESET
-_
ATITS LOWEST
POSITION
J !# tY
SETSCREW (C)
J, I I
SETSCREW (D)
&
SETSCREW (A) _
I I I I I
_SETSCREW
(E)
LOOPER COVER UNIT TO CHANGE THE FRONT COVER UNIT
TO REMOVE: 1. ATTACH THE...
Service Manual - Page 8
... NOT REMOVE OTHER BASE CUSHIONS. ATTACH THE TWO BASE CUSHIONS (F), WASHERS, AND TIGHTEN HINGE SCREWS (E). WASHER WASHER
\
BASE HINGE SCREW (E) CUSHION (F)
/
SETSCREW (D)
1 < SETSCREW (,_
REMOVE THE MACHINE BASE. ATTACH THE MACHINE BASE UNIT, AND TIGHTEN SETSCREWS (A), (B), (C) AND (D). 4. REMOVE SETSCREWS (A), (B), (C), (D) AND TWO HINGE SCREWS (E). TO CHANGE THE...
Service Manual - Page 9
... SETSCREWS (C). 6. REMOVE THE BACK COVER UNIT. 2. PULL OUT THE CORD CONNECTORS. ATTACH THE MACHINE SOCKET UNIT ON THE MOTOR FIXING PLATE. INSERTTHE CORD CONNECTORS AS SHOWN BELOW.
5. TO CHANGE THE MACHINE SOCKET
TO REMOVE: 1. REMOVE SETSCREWS (A), (B) AND THE MACHINE SOCKET UNIT FROM THE MOTOR FIXING PLATE. 3.
ATTACH THE BACK COVER UNIT.
¢
MOTOR...
Service Manual - Page 10
TURN THE HANDWHEEL TOWARD YOU AND SET THE NEEDLE BAR AT ITS HIGHEST POSITION. 3. REMOVE THE LOOPER COVER UNIT, FACE PLATE UNIT, BACK COVER UNIT, TOP COVER AND FRONT COVER UNIT. 2. SETSCREW (A)
SURFACE OF NEEDLE
PLATE...TOWARD YOU ONE CYCLE, AND RECHECK THE NEEDLE BAR HEIGHT. 5. TO ADJUST: 1. ATTACH THE FRONT COVER UNIT, LOOPER COVER UNIT, TOP COVER, BACK COVER UNIT AND FACE PLATE UNIT.
Service Manual - Page 11
... HOLE OF NEEDLE PLATE. 3. PRESSER BAR LIFTER
SETSCREW (A)
NEEDLE
TOP SURFACE OF NEEDLE
TO BE PARALLEL .__.l
R
_
PLATE
I
j
_\_ _] -_
4.7 ~ 5.3 MM
(DIRECTION OF PRESSER FOOT)
REMOVE THE LOOPER COVER UNIT, FACE PLATE UNIT, BACK COVER UNIT, TOP COVER AND FRONT COVER UNIT. 2. TO ADJUSTTHE PRESSER BAR HEIGHT
CORRECT SETTING: THE DISTANCE BETWEEN THE...
Service Manual - Page 14
... ON THE BALANCE WEIGHT WITH THE ONE ON THE MAIN SHAFT CORRECTLY. THE UPPER KNIFE SHOULD BE ALSO AT ITS HIGHEST POSITION WHEN THE NEEDLE BAR IS AT HIGHEST POSITION...SCREWS (A). 5.
DIRECTIO (C_) SETSCREW(B)
SETSCREW (A) 12 WHEN THE NEEDLE BAR GOES DOWN, THE UPPER KNIFE ALSO GOES DOWN.
@0
UPPER KNIFE DRIVE CAM
GUIDE LINE ON MAIN SHAFT
\
DIRECTION (D)
--(£_ ..... TURN THE HANDWHEEL ...
Service Manual - Page 15
... GET THE TIP OF
LOWER LOOPER IS IN LINE WITH GUIDE LINE OF GAUGE. 5.
REMOVE THE GAUGE AND SET THE UPPER KNIFE IN UP POSITION. TO ADJUST: 1. TO ADJUST THE HEIGHT OF THE LOWER LOOPER
CORRECT SETTING: THE HEIGHT OF LOWER LOOPER IS 65.7 MM FROM CENTER OF LOWER LOOPER SHAFT AS ILLUSTRATED BELOW. TIGHTEN...
Service Manual - Page 16
...THE STANDARD CLEARANCE BETWEEN THE LEFT AND RIGHT NEEDLE AND THE TIP OF THE LOWER LOOPER IS 0 MM TO 0.05 MM.
BEFORE LOOSENING SETSCREW (C), ATTACH THE NEEDLE GAUGE ...NEEDLE GAUGE
(787-G02)
(D)
NEEDLE BAR LOWER NEEDLE(L _-
(E) / NEEDLE
NEEDLE(R)
4 EOUALCLEARAN
LOWER LOOPER
14 REMOVETHE LOOPER COVER UNIT, FACE PLATE UNIT, BACK COVER UNIT, TOP COVER, FRONT
COVER UNIT, PRESSER FOOT AND ...
Service Manual - Page 17
... TO THE FRONT OR BACK.TIGHTEN THE HEXAGONAL BOLT B. REAR NEEDLE GUARD
7
1
,_
,_ IIp'L
FGR_NTNEEDLE _/_,_
HEXAGONAL
SCERWS (A)
. zz
SOCKET
HEXAGONAL BOLT (B)_
_ )_
LOWER LOOPER BACE
NEEDLE #11 _-x_
It_ 0 TO 0.1 MM
LOWER LOOPER REAR NEEDLE GUARD
15
TO ADJUST: 1. REMOVE THE LEFT NEEDLE ONLY, 2, TURN THE HANDWEEL TOWARDS YOU TO BRING THE TIP OF...
Service Manual - Page 18
... THE LEFT NEEDLE CLAMP. CHECK THE TIMING BETWEEN THE NEEDLE AND THE LOWER LOOPER. 5. PUSH THE RIGHT NEEDLE WITH THE FRONT NEEDLE GUARD TO ADJUST THE CLEARANCE BETWEEN
THE...CHECK THE CLEARANCE BETWEEN THE LEFT NEEDLE AND THETIP OFTHE LOWER LOOPER.
RECHECK THE NEEDLE BAR HEIGHT AND THE CLEARANCE BETWEEN THE NEEDLE AND THE LOWER LOOPER. LOOSEN THE HEXAGONAL SOCKET SCREW (A). 2. THE CLEARANCE SHOULD ...
Service Manual - Page 21
...: 1. TURN THE HANDWHEEL AND BRING THE UPPER LOOPER TO THE LEFTMOST POSITION. 5. TO ADJUST THE POSITION OF THE UPPER LOOPER
CORRECT SETTING: WHEN THE UPPER LOOPER IS ATTHE LEFTMOST POSITION, THE DISTANCE BETWEEN THE CENTER OF NEEDLE ON THE RIGHT AND THE CENTER OF LOOPER EYE SHOULD BE 4.8 TO 5.2 MM. REMOVE THE MACHINE BASE. 2. TIGHTEN THE HEXAGONAL SOCKET...
Service Manual - Page 22
... JUST LEFT OFTHE NEEDLE (#11) ON THE RIGHT. GO2). # CHECK THE CLEARANCE BETWEEN THE NEEDLE AND LOWER LOOPER. # CHECKTHE CLEARANCE BETWEEN THE LOOPERS.
8. REMOVE THE PRESSER FOOT, NEEDLE PLATE AND LEFT-SIDE NEEDLE. 2. REPLACE THE RIGHT SIDE NEEDLE WITH A#14 ONE. 9. IN THIS CONDITION, LOOSEN THE HEXAGONAL BOLT (C) JUST ENOUGH TO MOVE THE...
Service Manual - Page 23
... OF: (A): IF THE TIMING OF UPPER LOOPER IS ADVANCED AS SHOWN IN FIG. 3. (B): IF THE TIMING OF UPPER LOOPER IS DELAYED AS SHOWN IN FIG. 4. ATTACH THE MACHINE BASE. BEFORE PROCEEDING WITH THIS ADJUSTMENT, CHECKTHE LOWER LOOPER TIMING AND
POSITION OF UPPER LOOPER. 2. TIGHTEN TWO SETSCREWS. 5.
CHECK THE CLEARANCE BETWEEN THE LOOPERS. 6. REMOVE THE MACHINE BASE. 3. THE ALLOWANCE IS O.2TO...
Service Manual - Page 24
... THE SETSCREW FIRMLY. 5. OTO 0.1 MM
UPPER LOOPER /J
SETSCREW
t
LOWER LOOPER (FIG. 1)
UPPER _ LOOPER" __
(FIG. 3)
LOWER LOOPER
UPPER LOOPER
22
TO ADJUST: 1. LOOSEN THE SETSCREW, AND ADJUSTTHE CLEARANCE BY MOVING THE UPPER LOOPER TO
THE BACK OR FRONT AS SHOWN IN FIG. 3. 4. ATTACH THE NEEDLE PLATE AND PRESSER FOOT. CHECK THE CLEARANCE BETWEEN THE UPPER LOOPER AND NEEDLE: 6. TURN THE...
Service Manual - Page 25
... +0.05 MM ATTHE NEEDLE ON THE RIGHT. LOOSEN THE SETSCREW, AND ADJUST THE CLEARANCE BETWEEN THE BOTH NEEDLES AND
UPPER LOOPER. 3.
CLEARANCE
NEEDLE
I I_UPPER
LOOPER
(FIG. 1)
UPPER LOOPER
SETSCREW
UPPER LOOPER DRIVING SHAFT
(FIG. 2)
23
CHECK THE CLEARANCE BETWEEN LOOPERS. TIGHTEN THE SETSCREW. 4. TURN THE HANDWHEEL TOWARD YOU WITH YOUR HAND TO BRING THE NEEDLE JUST BEHIND
THE...
Service Manual - Page 26
... SHOULD BE LEVELED WITH THE SURFACE OF NEEDLE PLATE. TO ADJUST: BEFORE PROCEEDING WITH THIS ADJUSTMENT, CHECK THE UPPER KNIFE TIMING.
1.
WHEN THE UPPER KNIFE IS AT THE LOWEST POSITION, THE FRONT LOWER CORNER OF UPPER KNIFE SHOULD BE 0.8 TO 1.5 MM BELOW THE EDGE OF LOWER KNIFE. LOOSEN THE HEXAGONAL BOLT (B), AND ADJUST...
Service Manual - Page 27
...IS LINE WITH THE GROOVE OF LOWER LOOPER.
VIEW FROM (B)
LOWER LOOPER THREAD GUIDE (4)
LOWER LOOPER THREAD GUIDE (4)
LOWER LOOPER
AGREEMENT
UPPER LOOPER WAVING ARM
SETSCR_
LOWER LOOPER THREAD GUIDE (3)
(FIG. 1)
LOOPER THREAD TAKE - UP LEVER
(FIG. 2)
SETSCREW (C)
25 TIGHTEN SETSCREW C TO SECURE THE POSITION. TO ADJUSTTHE POSITION OF THE LOWER LOOPER THREAD GUIDE
LOWER LOOPERTHREAD GUIDE...
Service Manual - Page 28
... STITCH LENGTH IS SMALLER THAN 2.8 MM, TURN THE ADJUSTING SCREW IN THE DIRECTION (B). 4. ATTACH THE FRONT COVER UNIT, LOOPER COVER UNIT, TOP COVER, BACK COVER UNIT AND FACE PLATE UNIT. REMOVE THE LOOPER COVER UNIT, FACE PLATE UNIT, BACK COVER UNIT, TOP COVER AND
FRONT COVER UNIT. 3.
IFTHE ACTUAL STITCH LENGTH IS...
Service Manual - Page 29
... THE SEWING PERFORMANCE.
4.
ATTACH THE TOP COVER AND THE BACK COVER. TO ADJ UST THE THREAD TENSION DIALS
TO CHECK:
WHEN THE TENSION DIAL IS SET AT "3", THE STANDARD THREAD TENSION MEASURED WITH
WHITE POLYESTER THREAD (#50) SHOULD BE AS FOLLOWS:
• LEFT NEEDLE THREAD
36-48GRAM
• RIGHT NEEDLETHREAD • UPPER LOOPER...
Similar Questions
Kenmore Serger
In what order should the lower looper, upper looper, right needle, left needle be threaded? I've tri...
In what order should the lower looper, upper looper, right needle, left needle be threaded? I've tri...
(Posted by halliwellfour 11 years ago)
I Cannot Find A Manual For A Kenmore Sewing Machine Model# 385 81710
can anyone help me find a operators manual for this sewing machine?
can anyone help me find a operators manual for this sewing machine?
(Posted by janiceralston 11 years ago)
Kenmore Sewing Machine 1780 Button Attachment Plate.
Kenmore Sewing Machine Model 1780. I released the Button hole attachment coverplate and now it won't...
Kenmore Sewing Machine Model 1780. I released the Button hole attachment coverplate and now it won't...
(Posted by wespro57 12 years ago)
Kenmore Carrying Case (any Color)for Portable Sewing Machine
Where can I find a Kenmore Carrying case (any Color) for a portable sewing machine model 385.1764180...
Where can I find a Kenmore Carrying case (any Color) for a portable sewing machine model 385.1764180...
(Posted by epehler 12 years ago)
Cover Hem Stitch
I am new to sewing and serging. I am trying to figure out how to do a cover hem stitch.
I am new to sewing and serging. I am trying to figure out how to do a cover hem stitch.
(Posted by dutdesx3 13 years ago)