Kenmore 16677 Support Question
Kenmore 16677 Support Question
Find answers below for this question about Kenmore 16677 - Serger Sewing Machine.Need a Kenmore 16677 manual? We have 1 online manual for this item!
Question posted by dubrita on November 25th, 2011
Oil And Maintenance
Hi
I would like to use this serger but it has been standing for some time and there is no user manual. Do I need to oil it and where can I get a user manual?
Many thanks,
Rita.
Current Answers
Related Kenmore 16677 Manual Pages
Service Manual - Page 2
... THE FRONT COVER UNIT
4
TO CHANGE THE SIDE COVER UNIT
5
TO CHANGE THE MACHINE BASE
6
TO CHANGE THE MACHINE SOCKET
7
TO ADJUST THE NEEDLE HEIGHT
8
TO ADJUST THE PRESSER BAR HEIGHT
9
TO ADJUST THE FEED DOG HEIGHT
10
TO ADJUST THE TIMING OF THE NEEDLE AND THE FEED DOG
11
TO ADJUST THE...
Service Manual - Page 4
REMOVE THE BACK COVER UNIT.
TO CHANGE THE BACK COVER UNIT
TO REMOVE: 1. REMOVE SETSCREWS (B),(C) AND (D). 3. ATTACH THE SPOOL STAND WITH SETSCREWS (A),
/ RIB
RIB SETSCREW (B) SIDE COVER UNIT
\
SPOOL STAND
_UNIT
i
I
I
I
I
I
SETSCREW (A)
SETSCREW (C)
SETSCREW (D)
BACK COVER TO ATTACH: 4. PUT THE RIBS OF BACK COVER INTO THE FRONT COVER UNIT AND TIGHTEN SETSCREWS (B), (C) AND...
Service Manual - Page 8
... BASE CUSHIONS (F), WASHERS, AND TIGHTEN HINGE SCREWS (E).
TO ATTACH: 3. WASHER WASHER
\
BASE HINGE SCREW (E) CUSHION (F)
/
SETSCREW (D)
1 < SETSCREW (,_
REMOVE SETSCREWS (A), (B), (C), (D) AND TWO HINGE SCREWS (E). ATTACH THE MACHINE BASE UNIT, AND TIGHTEN SETSCREWS (A), (B), (C) AND (D). 4. TO CHANGE THE MACHINE BASE
TO REMOVE: 1. NOTE. DO NOT REMOVE OTHER BASE CUSHIONS.
Service Manual - Page 9
...
\
SETSCREWS (C)
LAMP SOCKET LEAD REMOVE THE BACK COVER UNIT. 2. TO ATTACH: 4. ATTACH THE MACHINE SOCKET UNIT ON THE MOTOR FIXING PLATE. TIGHTEN SET
SCREWS (A), (B). 7. ATTACH THE MACHINE SOCKET, AND TIGHTEN TWO SETSCREWS (C). 6. REMOVE SETSCREWS (A), (B) AND THE MACHINE SOCKET UNIT FROM THE MOTOR FIXING PLATE. 3. INSERTTHE CORD CONNECTORS AS SHOWN BELOW.
5. REMOVE TWO SETSCREWS...
Service Manual - Page 14
... COVER UNIT. 2.LOOSEN TWO SETSCREWS (A), AND MOVE THE BALANCE WEIGHT TO LEFT. 3.LOOSEN TWO SETSCREWS (B), AND ADJUST THE NEEDLE AND UPPER KNIFE TIMING. # TURN THE UPPER KNIFE DRIVE CAM TO THE DIRECTION (C) WHEN THE UPPER KNIFE TIMING
IS DELAYED. # TURN THE UPPER KNIFE DRIVE CAM TO THE DIRECTION (D) WHEN THE UPPER KNIFE...
Service Manual - Page 18
... AND THE TIP OF THE LOWER LOOPER SHOULD BE 0 MM TO 0.05 MM. TO ADJUST: 1.
ATTACH #14 NEEDLE TO THE LEFT NEEDLE CLAMP. CHECK THE TIMING BETWEEN THE NEEDLE AND THE LOWER LOOPER. 5.
Service Manual - Page 21
REMOVE THE MACHINE BASE. 2. LOOSEN THE HEXAGONAL SOCKET SCREWS (A), AND ADJUST THE DISTANCE BETWEEN
UPPER LOOPER SHAFT GUIDE AND ... BE 1.6T0 1.8 MM WHEN THE UPPER LOOPER IS ATTHE LOWEST POSITION AS SHOWN IN FIG. 1. 3. CHECK THE UPPER AND LOWER LOOPER TIMING AND THE CLEARANCE BETWEEN UPPER AND LOWER LOOPERS.
1.6 TO
1.7 MM
RIGHT
jjNEEDLE
ON THE
5 MM
.UPPER LOOPER UPPER LOOPER SHAFT GUIDEI...
Service Manual - Page 22
...CONDITION, LOOSEN THE HEXAGONAL BOLT (C) JUST ENOUGH TO MOVE THE LOWER LOOPER BASE. TO ADJUST THE TIMING OF THE NEEDLE AND THE LOWER LOOPER
CORRECT SETTING: WHEN THE NEEDLE COMES UP 2.8 TO 3.2 ... SET THE TWO GUAGES (787-G02, 787-G03), AS SHOWN IN (FIG. 1) AND TIGHTEN BOLT (B).
# THIS TIME, THERE SHOULD BE NO CLEARANCE BETWEEN THE GAUGES AND THE NEEDLE BAR LOWER BUSHING.
5. REMOVE THE GAUGE (787 -...
Service Manual - Page 23
BEFORE PROCEEDING WITH THIS ADJUSTMENT, CHECKTHE LOWER LOOPER TIMING AND
POSITION OF UPPER LOOPER. 2.
LOWER (FIG. 1)
R LOOPER
(FIG. 2)
\
(FIG. 4)
...AS SHOWN IN FIG. 4. CHECK THE CLEARANCE BETWEEN THE LOOPERS. 6.
ATTACH THE MACHINE BASE. TO ADJUST: 1. REMOVE THE MACHINE BASE. 3.
TO ADJUST THE TIMING OF THE UPPER AND LOWER LOOPERS
CORRECT SETTING: WHEN THE LOWER LOOPER MOVES TO...
Service Manual - Page 26
...: THE EDGE OFTHE LOWER KNIFE SHOULD BE LEVELED WITH THE SURFACE OF NEEDLE PLATE. TO ADJUST: BEFORE PROCEEDING WITH THIS ADJUSTMENT, CHECK THE UPPER KNIFE TIMING.
1. LOOSEN THE HEXAGONAL BOLT (B), AND ADJUST THE POSITION OF UPPER KNIFE. 4. LOOSEN THE TWO SETSCREWS (A), AND ADJUSTTHE LOWER KNIFE POSITION. 2.
UPPER KNIFE
HEXAGONAL BOLT (B)
.__...
Service Manual - Page 29
... IN THE DIRECTION (B).
* IF THE THREAD TENSION IS AT WEAKER LEVEL, SHIFT FHE ADJUSTING PLATE IN THE DIRECTION (C).
3. ROTATE THE THREAD TENSION DIAL WHILE SEWING TO CHECK THE SEWING PERFORMANCE.
4. FRONT COVER UNIT
TOP COVER
ADJUSTING PLATE (A)
t
27
ATTACH THE TOP COVER AND THE BACK COVER. REMOVETHE BACK COVER ANDTHETOP COVER. 2. TO...
Similar Questions
Kenmore Sewing Machine Model 158.17530.
as above: Older "cam" sewing machine that I LOVE! Model 158.17530 Need manual and or instructions ho...
as above: Older "cam" sewing machine that I LOVE! Model 158.17530 Need manual and or instructions ho...
(Posted by jeanandmarv 10 years ago)
I Cannot Find A Manual For A Kenmore Sewing Machine Model# 385 81710
can anyone help me find a operators manual for this sewing machine?
can anyone help me find a operators manual for this sewing machine?
(Posted by janiceralston 11 years ago)
Kenmore Sewing Machine 1780 Button Attachment Plate.
Kenmore Sewing Machine Model 1780. I released the Button hole attachment coverplate and now it won't...
Kenmore Sewing Machine Model 1780. I released the Button hole attachment coverplate and now it won't...
(Posted by wespro57 12 years ago)
Kenmore Carrying Case (any Color)for Portable Sewing Machine
Where can I find a Kenmore Carrying case (any Color) for a portable sewing machine model 385.1764180...
Where can I find a Kenmore Carrying case (any Color) for a portable sewing machine model 385.1764180...
(Posted by epehler 12 years ago)
Cover Hem Stitch
I am new to sewing and serging. I am trying to figure out how to do a cover hem stitch.
I am new to sewing and serging. I am trying to figure out how to do a cover hem stitch.
(Posted by dutdesx3 13 years ago)