InSinkErator Model SST-FLTR Support Question
InSinkErator Model SST-FLTR Support Question
Find answers below for this question about InSinkErator Model SST-FLTR.Need a InSinkErator Model SST-FLTR manual? We have 2 online manuals for this item!
Question posted by wernebur on January 17th, 2015
Re: Sinkerator Tank Sst-00
Tank is sputtering and spitting water when twisting delivery valve even with the power supply disconnected. Any help available? Thanks vey much
Current Answers
Related InSinkErator Model SST-FLTR Manual Pages
Specifications - Page 1
...
Recommended 30-125 psi Supply Pressure
Shipping Weight Approximately 7.7 lbs.
•
In sink erator®
The Next Necessity
HOT WATER DISPENSER
Dimensions
(1)
6-3/4"\
6-1/8"
Job Specifications
HWD387-11B-45-02
Instant Hot Water Dispensers
Model SST-FLTR
Stainless Steel Tank dispenses filtered near-boiling 200°F water instantly
Water dispenser sold separately
Submittal...
Owners Manual - Page 1
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalación, cuidado y uso Installation, soin et utilisation
CONTEMPORARY ANTIQUE TUSCAN MODERN
SST-FLTR
1.800.558.5700 www.insinkerator.com
44463 REV A
Printed in its sole
discretion, without notice or obligation and further reserves the right to change or discontinue models.
© 2011 InSinkErator, a division of...
Owners Manual - Page 2
...Moving parts inside the tank causing a rattling noise ...disposer, unless you have chosen the InSinkErator® Instant Hot Water Dispenser to be installed on the cold water line supplying water to use of a water...water dispenser may need for the dispenser's electrical power. The wall outlet powering your dispenser must have power supplied... the model of your instant hot water dispenser ...
Owners Manual - Page 3
...clear 5/16" tube off water supply.
Y ou may elect to 2 turns clockwise. If installing only new tank
a
TA ut rtnanokfftwopa...off tank fitting.
connect fitting and tighten brass nut with a wrench, 1 to use existing tank mounting bracket.
Property Damage: Unplug tank before disconnecting ...(3 pieces)
SST-FLTR
3/8" Tubes (2)
Brass Nut/Ferrule/ Tube Insert
4
6" Filter Discharge Tube...
Owners Manual - Page 4
...
E nsure that operates your dispenser must have power supplied to it ?
Many homeowners replace the soap dispenser... mounting hole for the dispenser with an instant hot water dispenser.
If drilling a hole into hole on side... 1/4" cap (not supplied). F rom under the sink. I dentify locations for your disposer, unless using the... for the dispenser faucet, tank and filter.
C heck to...
Owners Manual - Page 5
...DO NOT over the smooth plastic fitting and slide down through hole, first insert blue tube with water prior to Tank
a
3
W ithout depressing the gray button,
place the snap-connect fitting at
(1) (2)... screws.
Use wall anchorFserrule
(not supplied) for
this faucet is at marks. T he recommended installation for installation into brass seat helps hold
ring in an area that ...
Owners Manual - Page 6
...water supply line.
Install dedicated water control valve with automatic shut off .
H 3300: To dispense instant hot water, first press down on the faucet handle and then push the handle backward in instant hot water tank...head and twist clockwise until it until snug. To dispense cool water, first press down on the faucet handle and then pull the handle forward in - From water supply line
...
Owners Manual - Page 7
.... Use only the InSinkErator dispenser faucet supplied. Fire Hazard: To minimize possibility of... address, phone number, your InSinkErator Product model and serial number, and if necessary, ...water damage, replace any leakage could cause property damage. A drain pan, plumbed to the tank. No other type dispensers or valves to an appropriate drain or outfitted with which this instant hot water...
Owners Manual - Page 8
...Disconnect power from the spout. Push hot water dispenser faucet lever and allow water to check for 3 minutes before usage.
Hold tank upside down and discard. Insert new cartridge into filter head. Top surface of claims specified on hot water supply... if you will discharge from leakage, replace all testing performed at valve.
Pressure: 20-120 psi Temperature: 33ºF - 100º...
Owners Manual - Page 9
...ánea
Manual del usuario
CONTEMPORARY ANTIQUE TUSCAN MODERN
SST-FLTR
Instalación, cuidado y uso
Installation, Care & Use Installation, soin et utilisation
GN/HC1100 GN/HC2200 GN/HC2215 H/HC3300 Water is not switched off valve).
• Unscrew spout end piece and clean out any debris. Water discoloration/rusty • Corrosion of filter has expired.
•...
Similar Questions
Leaking Water From Below Tank When Tap Is Used
Whenever we use the hot water tap, water seems to be dripping below the tank. I cannot find a clear ...
Whenever we use the hot water tap, water seems to be dripping below the tank. I cannot find a clear ...
(Posted by aciditymilk06 6 months ago)
Sputtering With Hot Or Cold (disconnected Power)
Hi, I have SST-FLTR system that spits and sputters wether it is hot water or even when I disconnect ...
Hi, I have SST-FLTR system that spits and sputters wether it is hot water or even when I disconnect ...
(Posted by peralex1 5 years ago)
Why Is My Garbage Disposal Leaking On The Bottom
(Posted by shrnwashington 10 years ago)
Dishwasher Is Not Draining After Installing The Garbage Disposal.
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
(Posted by Drkisa 11 years ago)
I Have The Sst Fltr When Turned On It Sputters
(Posted by danielv 11 years ago)