InSinkErator Invite H990-SS Support Question
InSinkErator Invite H990-SS Support Question
Find answers below for this question about InSinkErator Invite H990-SS.Need a InSinkErator Invite H990-SS manual? We have 2 online manuals for this item!
Question posted by TOPanic on May 2nd, 2013
Threaded Stud
my threaded stud has fallen out - how do I put it back in? My dispenser moves around without this in.
Current Answers
Related InSinkErator Invite H990-SS Manual Pages
Specifications - Page 1
... changes in these designer finishes:
chrome, white, and biscuit
Sample Specification
Instant hot water dispenser(s) shall be InSinkErator Model H990-SS with each unit.
D532,497 (tank enclosure)
Specifications
Capacity Electrical Thermostat
2/3-gallon stainless steel tank dispenses 60 cups of Emerson Electric Co.
Required
1-1/4" - 1-1/2"
Hole Diameter standard sink hole
HWD394-11F...
Owners Manual - Page 1
TranScape™ View™ TranScape™ Wave™ HC3/GN3 H990 H770
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalacion, cuidado & uso Installation, soin et utilisation
Owners Manual - Page 2
...The use our water
filtration system. I It is normal. I Moving parts inside the tank causing a rattling noise is recommended that operates the
disposer, unless you may need a 11⁄4" - 11⁄2" ... instructions, cautions, warnings and dangers before installing or using an InSinkErator Instant Hot Water Dispenser. I If you may need to local codes.
I Make sure that you 'll...
Owners Manual - Page 3
...avoided, will require your instant hot water dispenser and record it here
HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SS GN3-SS H990-SS H770-SS
HOW TO USE THIS INSTRUCTION MANUAL
These ...manual:
INSTALLING THE FAUCET - View/Wave/HC3/GN3
A
View / Wave / HC3 / GN3
Unpack dispenser components.
2
On a firm, flat surface, carefully straighten the copper tubing.
3
Remove the wing nut...
Owners Manual - Page 4
... Small Steel Large Steel
2-1/4"
Fiber
Snap-Connect Fitting (3 pieces)
Tank
H-View-SS H-Wave-SS GN3-SS
Extension & Star Nut (View & Wave only)
Washers
1-5/8"
1-5/8"
3/4" Screws (2)
2-1/4"
2-1/4"
Rubber Small Steel Large Steel
Fiber
Wing Nut (HC3/GN3 only)
Snap-Connect Fitting (3 pieces)
Tank
3/4" Screws (2)
H990-SS
Semi-Circular Mounting Plate
Wing Nut
Snap-Connect Rubber Gasket...
Owners Manual - Page 5
...5 The wall outlet for the dispenser faucet, tank and filter (if applicable). I Check to wall thickness (depth)
HC-View-SS ...... 25⁄8 3" H-View-SS ........ 25⁄8 3" HC-Wave-SS .... 25⁄8 3" H-Wave-SS ...... 23⁄8 3" HC3-SS 21⁄4 3⁄4" * GN3-SS 21⁄2 3⁄4" * H990-SS .......... 11⁄4 3" H770-SS .......... 2 3⁄4"
* HC3/GN3, extension is...
Owners Manual - Page 6
...8260;8" Rubber Washer
Fiber Washer
Star Nut
Figure 1
Figure 2
If sink/counter thickness exceeds 3/4" a hole diameter of tubing. I Unscrew and remove threaded extension from the dispenser. I Unpack dispenser components.
Reinstall extension. Thread star nut onto extension until snug. VIEW/ WAVE
A
View / Wave
I On a firm, flat surface, carefully straighten the copper tubing using...
Owners Manual - Page 7
....
Tighten assembly using
hands only. D From faucet
3/8" white tube
An extension is at rest.
I Unpack dispenser components. HC3/ GN3
A
HC3 / GN3
I
7
Call 1-800-558-5700 to the ends of tubing.... 11⁄4" sink hole, place the
washers on the facuet base in place while securing the dispenser.
I Feed tubes down through the hole in this order (see diagram): 1) 15⁄8" ...
Owners Manual - Page 8
... be needed to ensure proper seal.
Tighten the wing nut until the base is at the desired angle. H990
A
H990
I Place wing nut onto the threaded stud.
I Unpack dispenser components. Do not distort the last 1 inch of the dispenser head and will surround the sink mount. I Ensure that the black rubber gasket
is at rest on...
Owners Manual - Page 9
...surface.
D
Half moon shaped metal mounting plate should cradle all descending tubes.
I Unpack dispenser components. H770
I On a firm, flat surface, carefully straighten the copper tubing using
hands only. Do not...the smaller hole. B
Fiber Gasket
Make sure to use fiber gasket to hold the dispenser head in the sink or countertop until snug.
9
H770
I Slide washer over the mounting screw,...
Owners Manual - Page 10
... use a pencil to mark locations for pinched or crimped tubes. Mount tank vertically in wood studs or cabinets only.
DO NOT over the far right smooth fitting and slide down as far ...pushed down
approximately 1/2". (3)
Property Damage: Pinched or blocked water lines may cause damage to the dispenser tank. The tank should be within 16" or less of faucet water lines and within reach...
Owners Manual - Page 11
...(both the hot and cold handles
independently if applicable).
H-View / H-Wave / GN3/ H990 / H770
I Install dedicated water control valve with 1/4" compression fitting (not included).
I ... a T-fitting (not included) onto the cold water supply line. Scalding Hazard: The faucet dispenses near-boiling (212ºF) water which can instantly cause scalds or
burns.
I At the...
Owners Manual - Page 12
...remove from accident, alteration, misuse, abuse, improper installation, installation not in your dispenser is properly grounded.
If your home. Purchase or installation receipt may not apply to... no cost to an appropriate drain or outfitted with the appliance -
WARRANTY INFORMATION
Dispenser:
3-year warranty
Stainless Steel Tank: 3-year warranty
Covers all local codes and ...
Owners Manual - Page 13
... reinstall drain screw into the bottom of water damage, immediately remove the unit from leakage, replace all cut, loose or split tubing. I Push hot water dispenser faucet lever
and allow water to clean the faucet and plastic components.
I Only use mild cleaners to boil.
I If filter system installed, remove and discard...
Owners Manual - Page 14
... www.insinkerator.com before calling AnswerLine™
TROUBLESHOOTING
PROBLEM
Water and steam spits forcefully from the tank.
• Adjust water temperature using dial on the dispenser faucet.
If the dripping doesn't stop after releasing lever. (HC3/GN3/View/ Wave)
• Mounting washers not installed properly
• Loosen mounting nut, 1/4 turn at...
Similar Questions
Badger Garbage Disposer 1-83
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
(Posted by oneputt824 8 years ago)
Why Is My Garbage Disposal Leaking On The Bottom
(Posted by shrnwashington 10 years ago)
Ball Bearing In Garbage Disposal
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
(Posted by Gbobeczko 11 years ago)
Dishwasher Is Not Draining After Installing The Garbage Disposal.
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
(Posted by Drkisa 11 years ago)