InSinkErator Invite H990-SS Support Question
InSinkErator Invite H990-SS Support Question
Find answers below for this question about InSinkErator Invite H990-SS.Need a InSinkErator Invite H990-SS manual? We have 2 online manuals for this item!
Current Answers
Related InSinkErator Invite H990-SS Manual Pages
Specifications - Page 1
... complete InSinkErator warranty is included in these designer finishes:
chrome, white, and biscuit
Sample Specification
Instant hot water dispenser(s) shall be InSinkErator Model H990-SS with each unit.
US Pat.
Required
1-1/4" - 1-1/2"
Hole Diameter standard sink hole
HWD394-11F-45-02
Complies with grounded three (3) prong plug
Snap-action, adjustable from 160˚F to...
Owners Manual - Page 1
TranScape™ View™ TranScape™ Wave™ HC3/GN3 H990 H770
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalacion, cuidado & uso Installation, soin et utilisation
Owners Manual - Page 2
... wall switch that operates the
disposer, unless you suspect elevated levels of chlorine in your water, it continuously. This unique appliance will prevent your dispenser, you 'll enjoy discovering new uses for commercial use our water
filtration system.
I Hole punch
If you intend to use of a water filter should not be controlled...
Owners Manual - Page 3
...: Do not pinch or break copper tubing. An imminently hazardous situation, which, if not avoided, will require your instant hot water dispenser and record it here
HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SS GN3-SS H990-SS H770-SS
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers...
Owners Manual - Page 4
... Small Steel Large Steel
2-1/4"
Fiber
Snap-Connect Fitting (3 pieces)
Tank
H-View-SS H-Wave-SS GN3-SS
Extension & Star Nut (View & Wave only)
Washers
1-5/8"
1-5/8"
3/4" Screws (2)
2-1/4"
2-1/4"
Rubber Small Steel Large Steel
Fiber
Wing Nut (HC3/GN3 only)
Snap-Connect Fitting (3 pieces)
Tank
3/4" Screws (2)
H990-SS
Semi-Circular Mounting Plate
Wing Nut
Snap-Connect Rubber Gasket...
Owners Manual - Page 5
...it continuously and must have power supplied to wall thickness (depth)
HC-View-SS ...... 25⁄8 3" H-View-SS ........ 25⁄8 3" HC-Wave-SS .... 25⁄8 3" H-Wave-SS ...... 23⁄8 3" HC3-SS 21⁄4 3⁄4" * GN3-SS 21⁄2 3⁄4" * H990-SS .......... 11⁄4 3" H770-SS .......... 2 3⁄4"
* HC3/GN3, extension is available by the same wall switch
that...
Owners Manual - Page 6
...1). I Feed tubes down through the hole in
the sink/counter until the base is required. Set faucet at desired angle. C
Fiber Washer
Hot & Cool models only
Star Nut...sink/counter hole.
I Attach the quick connector to hold the dispenser head in place. Large washer required for sink holes larger than 11⁄2"
I Leave small washers in place while securing the dispenser....
Owners Manual - Page 8
... the sink, place the semi-circular mounting plate onto the threaded stud.
H990
I Unpack dispenser components. Property Damage: Do not pinch or break copper tubing.
I Ensure that the black rubber ... angle.
C
An assistant may be needed to ensure proper seal. I Place wing nut onto the threaded stud. H990 I Feed tubes down the hole in place while securing the dispenser.
Owners Manual - Page 11
...within 30" of the copper 1/4" tube, slide the brass nut and ferrule provided with the dispenser. Gurgling or hissing is required under the sink. I Insert the white 3/8" tube into the 1/4" compression fitting and tighten.
6 FILL TANK & THEN... cold handles
independently if applicable). H-View / H-Wave / GN3/ H990 / H770
I Install a T-fitting (not included) onto the cold water supply line.
Owners Manual - Page 12
... to correct defects in material or workmanship in the dispenser system, excluding the replaceable filter cartridge, for the full warranty period from service any responsibility for the duration of ... do not assume any unit suspected of this system. Personal Injury: This tank is required during the warranty period, contact an authorized InSinkErator service agent to replace or repair the...
Owners Manual - Page 13
... warranty. Do NOT over tighten. I Only use mild cleaners to boil. I To put back into working order, install new filter cartridge (if required), fill tank with water and reconnect the electrical cord. (Refer to Page 11, Step 6)
PROPERTY DAMAGE
I Shut the cold... from leakage, replace all cut, loose or split tubing. CLEANING THE FAUCET AND TANK
I If filter system installed, remove and discard...
Owners Manual - Page 14
... new setting.
Water is boiling.
Divided stream.
• Debris in the water line reducing the pressure below 30 psi (i.e., a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off occurs.
• See page 6 or 7, Step 2B to run • Mounting nut too tight. Water continues to check proper mounting...
Similar Questions
Badger Garbage Disposer 1-83
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
(Posted by oneputt824 8 years ago)
Why Is My Garbage Disposal Leaking On The Bottom
(Posted by shrnwashington 10 years ago)
Ball Bearing In Garbage Disposal
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
(Posted by Gbobeczko 11 years ago)
Dishwasher Is Not Draining After Installing The Garbage Disposal.
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
(Posted by Drkisa 11 years ago)