InSinkErator Invite H770-SS Support Question
InSinkErator Invite H770-SS Support Question
Find answers below for this question about InSinkErator Invite H770-SS.Need a InSinkErator Invite H770-SS manual? We have 2 online manuals for this item!
Question posted by cfrakes on February 6th, 2016
The Unit Is Loose. How Do I Tighten? I Cannot See What To Do Under The Sink.
Unit is loose. How do I tighten? I cannot see under the sink? Please send a diagram if possible. What tool do I use?
Current Answers
Answer #1: Posted by TechSupport101 on February 6th, 2016 8:14 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. See the Installation Section of the User Manual here https://www.helpowl.com/manuals/InSinkErator/InviteH770SS/178072
Related InSinkErator Invite H770-SS Manual Pages
Specifications - Page 1
...hour
115 volts A.C., 750 watts, 6.25 amp heating element with each unit. All Rights Reserved. Dispenses near-boiling 200°F • 35... steel tank • Easy to adjust temperature control • Tool-free tank connections and dry start
protection to 210°F and...H770-SS
The original instant hot water dispenser with easy-to 210˚F (factory pre-set at any time, in the Care & Use...
Owners Manual - Page 1
TranScape™ View™ TranScape™ Wave™ HC3/GN3 H990 H770
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalacion, cuidado & uso Installation, soin et utilisation
Owners Manual - Page 2
...the sink for the dispenser's electrical power. See Step 1-B. We are confident that by following our step-by the same wall switch that operates the
disposer, unless...If you 'll enjoy discovering new uses for your home. I This particular unit is recommended to use our water
filtration system.
This unique appliance will prevent your stainless steel sink, you may need a basin wrench...
Owners Manual - Page 3
....
A potentially hazardous situation, which , if not avoided, will require your instant hot water dispenser and record it here
HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SS GN3-SS H990-SS H770-SS
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers, and subsections, indicated by -step narrative describing the...
Owners Manual - Page 4
...)
Washers
1-5/8"
1-5/8"
3/4" Screws (2)
2-1/4"
2-1/4"
Rubber Small Steel Large Steel
Fiber
Wing Nut (HC3/GN3 only)
Snap-Connect Fitting (3 pieces)
Tank
3/4" Screws (2)
H990-SS
Semi-Circular Mounting Plate
Wing Nut
Snap-Connect Rubber Gasket Fitting (3 pieces)
Tank
H770-SS
3/4" Screws (2)
Fiber Gasket
Metal Mounting Plate
Snap-Connect Mounting Screw Fitting (3 pieces)
Tank
4
Owners Manual - Page 5
...;8 3" HC3-SS 21⁄4 3⁄4" * GN3-SS 21⁄2 3⁄4" * H990-SS .......... 11⁄4 3" H770-SS .......... 2 3⁄4"
* HC3/GN3, extension is available by the same wall switch
that connects sprayer hose at left ) for the dispenser faucet, tank and filter (if applicable). It should not be fused.
I Check to rent or purchase
the appropriate tools. C
Required...
Owners Manual - Page 6
... hole I Unscrew and remove threaded extension from the dispenser. Large washer required for sink holes larger than 11⁄2"
Faucet is at rest. Reinstall extension.
I On a firm, flat surface, carefully straighten the copper tubing using
hands only. Reinstall threaded extension onto the base until snug (See Figure 2).
6 Thread star nut onto extension...
Owners Manual - Page 7
...faucet base in this order (see diagram): 1) 15⁄8" small steel washer 2) 15⁄8" small rubber washer.
I
7
I Attach the quick connector to order. Tighten assembly using
hands only. HC3 only
I On... Washer
11⁄4" Hole
Hole larger than 3/4" thick.
I For a 11⁄4" sink hole, place the
washers on the facuet base in place while securing the dispenser.
HC3...
Owners Manual - Page 8
... the threaded stud.
I On a firm, flat surface, carefully straighten the copper tubing using
hands only.
Tighten the wing nut until the base is at the desired angle.
B
Make sure to use rubber gasket to hold the dispenser head in the sink or countertop until snug, while ensuring the semicircular mounting plate extends beyond the...
Owners Manual - Page 9
...flat surface, carefully straighten the copper tubing using
hands only.
B
Fiber Gasket
Make sure to use fiber gasket to hold the dispenser head in the sink or countertop until snug.
9
Property ...base of dispenser. H770
I Position faucet head at rest on the sink or countertop surface. Tighten the screw until the base is now inside the smaller hole. H770
A
H770
I Feed tubes ...
Owners Manual - Page 10
... spot under the sink to mount
Tank ...use in place on the screws. I Tighten the screws with only 1/2 turn clockwise.
4
CONNECTING FAUCET TO TANK
A
I Slip the clear 5/16" tube over tighten...use a pencil to mark locations for hanging tank.
I Visually check for installation into place. (1)
I Slip the flexible white 7/16" tube over barbed middle fitting and slide
down as far as possible...
Owners Manual - Page 11
...water to cold water supply only.
Use care when operating this appliance.
Do not use an extension cord set with 3/8" ...required under the sink.
I Turn on the cold water supply.
H-View / H-Wave / GN3/ H990 / H770
I Check all ...dispenser.
I Insert the copper tube into the 3/8" compression fitting and tighten. 5
FINAL WATER CONNECTION
A
Brass Nut
Ferrule
Brass Inser
Plastic tube...
Owners Manual - Page 12
... with a qualified electrician or serviceman if you . Use of non InSinkErator components will void your home at ....
Fire Hazard: To minimize possibility of installation in the vicinity of installation. Periodically inspect the unit for the full warranty period... be required to replace or repair the unit in those applications where any loose or split tubing. DO NOT close vent...
Owners Manual - Page 13
...void the warranty. CARE AND USE
Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit.
I Regularly inspect the unit for any leakage could cause ...loose or split tubing. I To put back into empty pail. For fresher tasting water, add filtration to unplug the unit and drain it is 200˚F.
Do NOT over tighten. I To avoid water damage from unit...
Owners Manual - Page 14
POSSIBLE CAUSE
• Unit is blocked.
• Unplug the unit.
Divided stream.
• Debris in the water line reducing the pressure below 30 psi...any debris.
Allow 5-7 minutes for 20 seconds to release some water from the tank.
• Adjust water temperature using dial on the dispenser faucet. If the dripping doesn't stop after releasing lever. (HC3/GN3/View/ Wave)
&#...
Similar Questions
Badger Garbage Disposer 1-83
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
loosened up hex screw of bottom of disposer to remove spoon and success. Now try to tighten it but p...
(Posted by oneputt824 8 years ago)
Does Not Get Hot
water is not hot. it just seems not to wok anymore
water is not hot. it just seems not to wok anymore
(Posted by jamescrof 10 years ago)
Why Is My Garbage Disposal Leaking On The Bottom
(Posted by shrnwashington 10 years ago)
Ball Bearing In Garbage Disposal
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
(Posted by Gbobeczko 11 years ago)
Dishwasher Is Not Draining After Installing The Garbage Disposal.
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
(Posted by Drkisa 11 years ago)