Husqvarna RZ46i Support Question
Husqvarna RZ46i Support Question
Find answers below for this question about Husqvarna RZ46i.Need a Husqvarna RZ46i manual? We have 2 online manuals for this item!
Question posted by paulsalina2 on September 6th, 2021
Mandrel Bolts Rz46i
just bought a mandrel from you an got it but I need the 4 bolts!!! Have an RZ46i
Current Answers
Answer #1: Posted by hzplj9 on September 6th, 2021 12:28 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,874,710
Member since:
June 25th, 2012 Points: 4,874,710
I do not believe you purchased items from us as we are just a help site not a spares supplier. I would advise going back to your retailer who supplied the original part for advice. However if you have no joy then if you look at this link it shows you the parts available for your mower. You should then be able to obtain the items you need. Item 2 of the drawing specifies a bolt.
Hope that enables you to get a resolution to your problem.
Answer #2: Posted by SonuKumar on September 7th, 2021 1:02 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/husqvarna/ride-mower/yth-1542-xp-2003-10/mower-deck?__cf_chl_captcha_tk__=pmd_URiNlMteevaPUYLHlXUXcT2.jTVC5T5jC21JyLcycF8-1631001670-0-gqNtZGzNAxCjcnBszQi9
please check carefully, the entire product should contain the bolts as well
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Husqvarna RZ46i Manual Pages
Owners Manual - Page 1
Operator Manual
RZ46i / 967277602
Please read the operator manual carefully and make sure you understand the instructions before using the machine.
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
Owners Manual - Page 5
...repairs must only be used for purchasing a Husqvarna ride-on lawns and even ground without obstacles such as stones, tree stumps, etc. Lawn mowers and all who are documented. Use only approved repair parts...If the machine is well anchored. Operating
This machine is built for mowing grass on mower.
The final chapter of uses are used improperly. Make wide turns to change without ...
Owners Manual - Page 10
...8226; Disengage blades when not mowing. These operators should evaluate their ability to operate the riding mower safely enough to cause cancer, birth defects, or other debris, causing buildup to occur.
... artificial light.
• Do not operate the machine while under the influence of riding mower-related injuries. Shut off engine and wait for wheel weights or counterweights.
• Anyone...
Owners Manual - Page 12
... and be a minimum of 16 years of a child. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. They may block your view of age before operating a riding lawn mower.
Never assume that children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful care of...
Owners Manual - Page 14
...repairs with the engine running the engine with manufacturer's recommended parts, when necessary.
• Mower blades are properly tightened and torqued. Repair, if necessary, before storing.
• If ...a closed area.
• Keep all nuts and bolts tight to be sure the equipment is in good condition and that all nuts and bolts, especially those fastening the blade attachments, are sharp...
Owners Manual - Page 16
...setting the park brake. Blade switch fault light
If the park brake is started when:
• The mower blades are disengaged.
• The park brake is on.
• The motion control levers are in ...fault.
8058-241 8058-238
Park brake and blade switch fault lights
8058-243
16
The blades will need to be reset (pushed down and the blade switch and park brake lights will continue to re-...
Owners Manual - Page 24
... obtain an even cutting height, it is important that the air pressure in the Operation section to the blade tip with the engine not running.
Mower deck lifting lever
Bypass Linkages
The levers are handled.
24
Left side bypass linkage
8011-419 8058-251 8058-0147 Bypass linkages are measured from...
Owners Manual - Page 35
... height and reduce it is important that the mowing interval is used without negatively affecting the mowing result.
• The finest lawns are obtained by the blades. Make sure the mower is cooled and the engine is off.
• Use compressed air to clean top surface of stones and other fixed objects...
Owners Manual - Page 40
...two wrenches for charging times. WARNING!
MAINTENANCE
Battery
Your mower is not necessary. Open the terminal access doors. 2.... the battery with a maintenance free battery and does not need servicing. Replacing battery 1. Connect BLACK grounding cable to positive...8226; Keep battery and terminals clean. • Keep battery bolts tight. • See chart for the terminal screws. Carefully...
Owners Manual - Page 42
...the operating position. IMPORTANT INFORMATION
Adjust anti-scalp rollers with the mower on a flat level surface. The rollers should be at the... solid tires will cause premature failures. Remove nut and caster bolt. 2. Caster wheels 42
8011-564 8058-135 8058-055
... Rollers
Anti-scalp rollers are properly adjusted when they are just slightly off of tire liner or foam fill material to support...
Owners Manual - Page 43
... operation. Route the belt forward and up onto the deck.
3. Place belt around the mandrel housings.
5. Correct if needed.
7.
Apply parking brake. 2. Remove any twist. Belt shields 2. Wrap the deck belt... the belt over stationary idler pulley. Push inward on the engine shaft.
2. Remove bolts from wear. NOTE: The belt will show some small cracks in installing the deck ...
Owners Manual - Page 44
... of blades should decide whether the blade can be repaired/ground or must be carried out by turning counterclockwise.
2. Remove blade bolt by an authorized service workshop. Blade bolt (special) 3. Tighten blade bolt securely.
5.
WARNING!
Install new or resharpened blade with stamped
GRASS SIDE facing towards ground/grass
(down) or THIS SIDE UP...
Owners Manual - Page 53
...
242
323
330
440
471
628
596
794
904
1205
Accessories
Collection system, mulch kit
53 Grade
U.S. TECHNICAL DATA
Torque Specifications
Engine crankshaft bolt Deck pulley bolts Lug nuts Blade bolt
75 ft/lb (100 Nm) 75 ft/lb (100 Nm) 75 ft/lb (100 Nm) 55 ft/lb (75 Nm)
Standard ¼...
Owners Manual - Page 58
... the 50-hour service Change the engine oil filter Clean/replace the spark plugs Replace the fuel filter Check V-belts Check tighten caster wheel axle bolts (every 200 hours) Change the air filter's paper cartridge
Date, mtr reading, stamp, sign
q q q q q q q q
58
Parts Manual - Page 5
..... 874 780536 6 HCS 5/16-18 x 2¼ 23.. 874 780416 2 HCS ¼-20 x 1 24.. 874 780648 8 HCS 3/8-16 x 3 25.. 872 141608 4 RHSNB 3/8-16 x 1 26.. 874 490644 6 BOLT 3/8-16 x 2¾ THD FRM 27.. 819 141614 6 WASHER 3/8 STD FLT 28.. 819 111116 �� 13 WASHER 5/16 SAE FLT 29.. 819 091016 2 WASHER ¼...
Parts Manual - Page 7
...-20 x 2½ 21.. 874 780852 1 HCS ½-13 x 3¼ 22.. 874 520656 1 HCS 3/8-16 x 3½ 23.. 817 120616 4 HHFS 3/8-16 x 1 THD FRM 24.. 817 490512 4 BOLT 5/16-18 x ¾ THD FRM 25.. 539 976979 2 NUT 3/8-16 HEX NYLOC 26.. 873 800800 1 NUT ½-13 HEX NYLOC 27.. 539 112899 5 NUT 5/16...
Parts Manual - Page 9
..., ROD END 17.. 874 780844 2 HCS ½-13 x 2¾ 18.. 874 780516 2 HCS 5/16-18 x 1 19.. 874 780524 1 HCS 5/16-18 x 1½ 20.. 874 490512 8 BOLT 5/16-18 x ¾ THD FRM 21.. 874 780528 2 HCS 5/16-18 x 1¾ TPBLT 22.. 578 296403 4 SCREW 5/16-18 X 1¼ BTN HD 23.. 576 850402...
Parts Manual - Page 11
..., NEGATIVE BLK 25" 37.. 585 734303 1 CABLE, POSITIVE RED 17" 38.. 872 140506 2 RHSNB 5/16-18 x ¾ 39.. 872 140608 2 RHSNB 3/8-16 x 1 40.. 817 490408 2 BOLT ¼-20 x ½ 41.. 539 110673 4 SCREW 10-24 x ¾ WSH HD 42.. 539 990411 2 SCREW 10-24 x ½ HEX HD 43.. 539 111229 1 SCREW...
Parts Manual - Page 19
...131491 1 ROD, HINGE 26.. 574 689002 1 ARM, IDLER
ITEM PART NO. QTY. QTY. MOWER DECK / CUTTING DECK
ITEM PART NO. DESCRIPTION
27.. 539 115574 1 EYEBOLT 5/16 x 3&#...2 STUD w/ANTI-
ROTATE 30.. 532 193406 3 BOLT 3/8-16 x 35/8 SHOULDER 31.. 539 113621 2 BOLT 3/8-16 x 3/8 SHOULDER 32.. 532 193003 2 BOLT, WASHER 33.. 539 128101 1 BOLT 3/8-16 x 2¼ CARRIAGE 34.. 872 140506 7...
Parts Manual - Page 21
...; 12.. 510 422701 2 RHSNB 5/16-18 x 2½ 13.. 874 780620 2 HCS 3/8-16 x 1¼ 14.. 874 780610 1 HCS 3/8-16 x 5/8 15.. 817 490512 4 BOLT 5/16-18 x ¾ THD FRM 16.. 539 110303 2 BOLT 5/16-18 SHOULDER 17.. 539 112899 4 NUT 5/16-18 HEX FLG NYLOC 18.. 539 111897 1 WASHER 3/8 SPECIAL 19.. 819 141614 2 WASHER...
Similar Questions
Husqvarna Riding Lawn Mower Starts, Blade Spins, Won't Go Forward Nor Reverse
(Posted by shywolfalways82 3 years ago)
Smart Switch On Husqvarna Rz46i, Stays Blue. Resetting Code Does Not Help.
I'm in the seat, mower deck up. blades off, handles out. No indicator lights saying there is a probl...
I'm in the seat, mower deck up. blades off, handles out. No indicator lights saying there is a probl...
(Posted by rlwatty1 4 years ago)
What Is A 2012 Husqvarna Hu 775l Lawn Mower In Very Good Condition Worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
(Posted by kpcastles 7 years ago)
Smartswitch S/s Is A Solid Blue
when i sit on the mower the smartswitch lights up as it should and the s/s is blinking blue. Once i ...
when i sit on the mower the smartswitch lights up as it should and the s/s is blinking blue. Once i ...
(Posted by Zgulker 7 years ago)
My Husqvarnarz4623 Lawn Mower
My husqvarna lawn mower will not start. It wont even try to turn over or click.
My husqvarna lawn mower will not start. It wont even try to turn over or click.
(Posted by teresaandbryancates 9 years ago)