Husqvarna MZ 5225 Support Question
Husqvarna MZ 5225 Support Question
Find answers below for this question about Husqvarna MZ 5225.Need a Husqvarna MZ 5225 manual? We have 2 online manuals for this item!
Question posted by jainsworth on August 30th, 2020
Clutch Stop!!!
Had good intentions to change the Hyd Motor belt in MZ5225. Followed instructions and removed the "clutch stop." Then decided that job would take too long for now. Reinstalled the "clutch stop", and noticed there were two notches in the clutch assembly. Could not tell which one I removed from the stop. Installed - started mower - Left stick will move as advertised - Right stick will not perform action - feels like it is locked. I am "assuming" that I installed the clutch stop in the wrong position. Does anyone know why two positions and how to pick the correct one? One other thing - I did change the deck belt but I don't know why that would affect the driving.
Requests for more information
Request from jainsworth on August 30th, 2020 8:03 PM
I saw the instructions in the manual and all it says is to "install/secure the clutch stop. That doesn't answer my question. My question is how do I know which notch on the clutch (there are two) is the correct notch to install the "stop" into.
I saw the instructions in the manual and all it says is to "install/secure the clutch stop. That doesn't answer my question. My question is how do I know which notch on the clutch (there are two) is the correct notch to install the "stop" into.
Current Answers
Answer #1: Posted by INIMITABLE on August 30th, 2020 1:54 PM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,088,520
Member since:
April 3rd, 2020 Points: 2,088,520
Here is a guide video
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Answer #2: Posted by hzplj9 on August 30th, 2020 1:58 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,670
Member since:
June 25th, 2012 Points: 4,875,670
Refer to the manual available form this link:
https://www.manualslib.com/products/Husqvarna-Mz-5225-3081956.html
Page 40 of the PDF explains setting the drive pulley which involves the clutch pulley. There are specific instructions as to the procedure. Changing the drive belt seems to have had some influence on your issue.
Hope that helps if it does please mark as such thank you.
Related Husqvarna MZ 5225 Manual Pages
Owners Manual - Page 3
...Towing 5 Operating 5 Good Service 6
Symbols and Decals 7 Safety 9
Safety Instructions 9 General Operation 9 ... Operating on hills 32 Mowing Tips 33 Stopping the Engine 34 Pump release valves 35...43 V-belts 43 Deck belt 44 Pump Belt 45 Cutting Blades 45
Blade replacement 46 Adjusting the Mower Deck... 52 Changing the Engine Oil 52 Engine Oil Levels 53 Hydraulic Pump 54 Fluid Change 54...
Owners Manual - Page 5
.... Operating instructions for the accessories are provided with the machine's special characteristics and who operate this machine, it may jackknife or overturn causing damage to the mower and possible serious injury to the drive system. This machine is constructed only for mowing grass on public roads. If you must be followed without notice. Driving...
Owners Manual - Page 9
... .
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. The machine is clear of bystanders before mowing
8011-513
English-9 Material may ricochet back toward anyone enters the area.
• Never carry passengers. Shut off blades, set parking brake, stop before cleaning the machine, removing the grass catcher, or...
Owners Manual - Page 11
...slope or if you feel uneasy on the slopes slow and gradual. Do not make sudden changes in speed or direction, which can get caught in choosing the right equipment.
• ...speed so that can result in illustrations) shall be used. Tires may lose traction.
• Avoid starting, stopping, or turning on wet grass. When using the machine.
• Never use the machine when barefoot.
...
Owners Manual - Page 14
... object, stop and inspect the machine. Adjust and service as required.
• Maintain or replace safety and instruction labels, ...recommended parts, when necessary.
• Mower blades are considered to be driven with defective or ...other protective devices.
• Do not change the settings of grass, leaves, or...burns. Clean oil or fuel spillage and remove any adjustments or repairs with the engine ...
Owners Manual - Page 17
...kg. • Read machine operator´s manual before each use. • Securely fasten your seat belt if the unit has
a ROPS. • Where possible, avoid operating the unit
near any unimproved... by the operator.
This mower is equipped with a spark arrester meeting applicable local or state laws (if any part of the unit by damage if the mower is stopped, set brakes securely and...
Owners Manual - Page 21
...
Choke control
7.
CONTROLS
5. For cold starts the control should be pulled out to start and stop the engine.
6. They are located on the control panel and is used to its extent. ...to provide the engine with ratings and functions:
• 20 A, Primary fuse. • 7.5 A, Mower deck coupling.
Fuses
8061-003
8061-004
8011-420
English-21 Choke Control
The choke control is used ...
Owners Manual - Page 25
... wheel. As long as concrete or blacktop PRIOR to attempting to operate on control levers to the neutral position and mower should stop . This will allow mower to start moving...or until the mower stops or slows dramatically.
Then by NOT moving .
operation
Read "Safety Instructions" section and following pages, if you are far more maneuverable than typical riding mowers due to ...
Owners Manual - Page 32
... turn) can be used before starting up or down hills.
• Avoid stopping or changing speed on Slopes" in the "Safety Instructions". Do not drive up or down hills with slopes greater than 10 degrees. This may cause the mower to suddenly stop.
• To restart movement, release the parking brake.
• Pull the control...
Owners Manual - Page 33
... degrees. Avoid sudden directional changes.
English-33 If the grass is poorer because the wheels sink into the transport position. The mowing result is not too long and dense, the driving...8226; The mowing result will be raised into the soft lawn, clumps build, and the grass clippings fasten under the cowling.
• Hose the mower deck underside with a high engine speed (the blades ...
Owners Manual - Page 34
... the engine to idle a minute in neutral position to stop position.
8061-013
Disengage the mower deck and move throttle to minimum
• Move the steering controls outward.
• Remove key. Turn the ignition key to the stop
8061-011 Always remove key when leaving the mower to the minimum position (tortoise symbol).
Avoid idling the...
Owners Manual - Page 37
..." position and remove the key. • Make sure the blades and all moving parts have completely stopped. • ...Disconnect the spark plug wire from all spark plugs and place the wire where it
cannot come in this manual = Not described in contact with a heavy load or at reservoir Change hydraulic oil & filter (200 hours) Clean fins of belts, belt pulleys Change...
Owners Manual - Page 39
...for starting or driving under the following conditions. MAINTENANCE
Ignition System
The engine...can only be .030" (0.75 mm). Change the conditions and try again.
The engine can...stops if the mower blades are engaged and the driver temporarily moves off and repair the safety system before the steering controls can be moved into the neutral position, otherwise the engine will stop. Remove...
Owners Manual - Page 44
Using a ratchet with fasteners.
5
Belt routing, deck belt
8011-622 8011-580
English-44
Route the belt forward between and up onto the deck.
3. The belt can now be removed. Wrap the belt around the stationary idler
1
pulley and around the electric clutch on the engine shaft.
6. Remove the belt from around the mandrel housings.
5. Push inward on the spring...
Owners Manual - Page 45
... mower on the pump idler arm. 5. Remove the deck belt (see Deck Belt Removal in this section of blades should now be able to access the belt. 3. Disconnect clutch wire. 4. Belt installation 1. Route the belt around the inside of the manual). 2. Reconnect clutch wire. 6. Reinstall the deck belt. (see Deck Belt Removal in this section of the idler pulley. 3. Clutch stop Pump belt...
Owners Manual - Page 47
...mower deck. NOTE:To insure accuracy of leveling procedure, mower deck drive belt must be adjusted slightly higher in slot until rear of mower...position and remove the key. 4.
Turn ignition switch to the bottom of the mower deck. ...stopped. 5. MAINTENANCE
Adjusting the Mower Deck
WARNING!
Blades are inflated to -side manner.
2. Slotted deck hanger plates
Leveling the mower...
Owners Manual - Page 53
...including filter 1.7 qt (1.9 liters).
The oil is recommended at all temperatures.
Remove the dipstick, wipe it clean, and then replace it. Remove the dipstick
The oil level should lie between -18 °C/0 °F and...30, 10W-30 can be used between the markings on the dipstick. If the level is stopped. Synthetic oil SAE 5W-30 or 10W-30 is filled through the hole for the dipstick....
Owners Manual - Page 54
...of maintenance. Shortened component life. Fluid fill lines Changing the hydraulic pump oil filter
8061-016
Before ...High operation temperature and excessive expansion of power or drive after stopping the engine.
4. Check the oil level and add oil...Reinstall the tank cap by hand. As air is recommended. Remove the cap from the pump's tank located on the reservoir. The following...
Owners Manual - Page 76
... out and mailed to Husqvarna Forest & Garden Company. The product must be followed as herein stated.
SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be normally located through normal regular use (when used , but not limited to, belts, blades, blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw crankshafts for commercial...
Parts Manual - Page 7
...
1.. 574 846302 1 PLATE, ENGINE 2.. 574 846402 1 PLATE, IDLER SUPPORT BLK 3.. 574 870901 1 BELT, HYDRO 4.. 574 811001 1 PULLEY 5.. 539 976688 1 PULLEY, IDLER 6.. 539 107620 1 PULLEY, IDLER... BRACKET, MUFFLER 19.. 539 131604 1 MUFFLER 20.. 539 101714 1 SOLENOID 21.. 575 017302 1 STOP, CLUTCH 22.. 539 102759 3 INSULATOR 23.. 539 101362 1 HOSE, DRAIN 24.. 539 101364 1 PLUG,...
Similar Questions
What Is A 2012 Husqvarna Hu 775l Lawn Mower In Very Good Condition Worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
(Posted by kpcastles 7 years ago)
Lawnmower Will Not Crank Or Turn Over After Shut Off. Help!!!
turned mower off was running fine. The battery is fine oil level is fine
turned mower off was running fine. The battery is fine oil level is fine
(Posted by therevhub 7 years ago)
Blades Will Not Engage Once The Mower Has Been Running For A While.
Once mower has been running and after emptying bags, the PTO pulled up will not engage blades. If it...
Once mower has been running and after emptying bags, the PTO pulled up will not engage blades. If it...
(Posted by abecker4 7 years ago)
Hi, My Mz Won't Start! Battery Checked, Sparks Plugs Checked..! Can't Locate
where the starter motor is.
where the starter motor is.
(Posted by bestmatecleaning 8 years ago)
My Husqvarnarz4623 Lawn Mower
My husqvarna lawn mower will not start. It wont even try to turn over or click.
My husqvarna lawn mower will not start. It wont even try to turn over or click.
(Posted by teresaandbryancates 9 years ago)