Hunter 81003 Support Question
Hunter 81003 Support Question
Find answers below for this question about Hunter 81003.Need a Hunter 81003 manual? We have 2 online manuals for this item!
Question posted by danielbabik on March 28th, 2018
Slow Motor
need a replacement motor for 81003 bathroom fan. Where can I get the mo
Current Answers
Related Hunter 81003 Manual Pages
Owner's Manual - Page 1
Owner's Manual
Model
81003
1
41937-01 10/26/2010 Ashbury
Bath Ventilator with Light
English
41937-01 20101026 ©2010 Hunter Fan Co.
Owner's Manual - Page 2
...;
45°
MAINTENANCE
The motor is needed for Heating, Refrigeration and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.
5. You should replace the impeller at service panel ...the power supply and clean the fan as dishwashing liquid, and a soft cloth. If the motor bearings are making excessive or unusual noises, replace the motor with all applicable codes and standards...
Owner's Manual - Page 3
If damaged, call 1-888-830-1326 for model 81003
Included. x4 A
*B *C
3/8" Cable Connector
x2 D
Extra Screws
* NOTE: Strain relief cable connector must be installed.
Before Installation
1
Tools Needed. (Not supplied.) Estimated assembly time: 30 to 60 ...-01-214 for model 81001 96397-02-444 for model 81003
M 75184-01-133
N 86812-01-000
O
75733-01-214 for model 81001 75733-01-444 for...
Owner's Manual - Page 4
3
4
H
E
Remove the motor/blower from the housing.
5
Remove packing material.
6
Remove the pre-loaded screw tip covers.
7
G
Back out the pre-loaded screw tips until flush with the side of the housing.
8
F
Remove the wiring cover screw.
4
41937-01 10/26/2010
Remove the wiring cover.
Owner's Manual - Page 5
... to step A11, page 5 For Existing Construction - B
Insert the strain relief (not included) into joist or framing.
5
41937-01 10/26/2010
Use second if needed.
go to step B11, page 8
New Construction
A11
A12
E
5/8
5/8
1/2
1/2
Position the correct depth mark at the bottom edge of the joist based on the thickness...
Owner's Manual - Page 6
If ducting does not fit securely, an adapter may need
to the outside. A15
A016
E
G
F
Install the wiring cover plate. For supply connection,... connections are inside the box or under
the wiring cover plate.
Tape joints. A14
Fan Motor Light
2 Pin
Black White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In...
Owner's Manual - Page 7
... housing. A21
ON
A22
Go to attach grille. Test the motor. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. H
Reinstall the motor by tightening the 2 screws. Turn on page 10
to step
C1
OFF
on the power source. If the motor does not run, check the plug connection.
7
41937-01 10...
Owner's Manual - Page 8
... 1
Route wires through the strain relief. If ducting does not fit securely,
an adapter may need to duct connector.
Move the housing into the joist.
8
41937-01 10/26/2010 B15
...to be purchased.
Existing Construction
B11 EXISTING FAN
B12
E
Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor
housing (7 1/4"x 7 3/4"). E
Install ...
Owner's Manual - Page 9
... tightening the 2 screws.
41937-01 10/26/2010 B19
H
Connect wiring harness.
DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS.
B16
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch 2 (AC In...
Owner's Manual - Page 10
B22
ON
OFF
Test the motor.
Attaching the Grille
C1
C2
L
M
Remove the thumbscrews.
10
41937-01 10/26/2010
N
O
Remove glass dome. If the motor does not run, check the plug connection. B23
Go to step
C1
on the power source. B21
Turn on page 10 to attach grille.
Owner's Manual - Page 11
... the strain relief bracket screw. C8
L
L
M
Align posts 1, 2, and 3 (stamped into motor housing) with
posts 1, 2, and 3 (stamped into light fixture). Remove the strain relief bracket screw. C7
Insert the strain relief bracket's dog-leg tab so ...41937-01 10/26/2010 DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. C5
C6
J
Position the strain relief bracket under the motor as shown.
Owner's Manual - Page 13
...need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.
13
41937-01 10/26/2010 Solution: • Replace the light bulb with a new bulb. • Turn power on, replace... wiring diagram. To confirm that the fan is running, place your hand near the vents to feel the air movement.
• Turn power on, replace fuse, or reset breaker. •...
Owner's Manual - Page 14
... us . If we will repair or, at our option, replace the defective part free of charge for parts and labor performed at our nearest service center or at our Service Department in Memphis, Tennessee. Proof of purchase.
If your Hunter bath exhaust fan motor fails at any time within one -year period, you...
Similar Questions
Need Replacement Fan For Hunter Bathroom Exhaust Fan 83001/83701
Need replacement fan for Hunter bathroom exhaust fan 83001/83701
Need replacement fan for Hunter bathroom exhaust fan 83001/83701
(Posted by smstraka 2 months ago)
Hello, I Have A Hunter Ceiling Fan Model 20715, I Need A Replacement Motor. Than
(Posted by abels999 1 year ago)
I Need A Replacement Glass For Cover On This Item. How Can I Buy It?
I need replacement glass for this item
I need replacement glass for this item
(Posted by pwhitwam 5 years ago)
Hunter Ashbury Bath Ventilator With Light 81003
I need to get a price in part 95261-02-000 and does this include the capacitator
I need to get a price in part 95261-02-000 and does this include the capacitator
(Posted by Conniepoynter 8 years ago)
I Need Replacement Glass Globe For This Fixture Part# 96395-01-000
(Posted by marilyndmorgan 10 years ago)