Hunter 44260 Support Question
Hunter 44260 Support Question
Find answers below for this question about Hunter 44260.Need a Hunter 44260 manual? We have 2 online manuals for this item!
Question posted by kittydale9 on January 19th, 2020
Why Is My Thermostat Flashing A 4
why is my thermostat flashing a 4
Current Answers
Related Hunter 44260 Manual Pages
Owner's Manual - Page 1
Set & $ave
Programmable Thermostat
installation and operation manual
English
Form# 42711-01
20091118
©2009 Hunter Fan Co.
1
Model
44260
Owner's Manual - Page 3
Table of Contents
Important Information 5
Tools
6
Uninstalling the Existing Unit 7
Installing the Thermostat 12
installing the wall plate 12 connecting the wires 16 attaching the thermostat 18
Settings 22
Methods of Operation 26
manual operation 28 default programs 32 creating custom programs 34
Icons and Features 38
Wiring 49
Troubleshooting 52
3
Owner's Manual - Page 4
Please read this manual before beginning installation and save this booklet for choosing a Hunter programmable thermostat.
Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Thank you for complete operation instructions.
4 Set & Save
Programmable Thermostat
Model 44260
Congratulations!
Owner's Manual - Page 5
... Electric Air Conditioning Single Stage Heat Pump - Fired Boilers Gas - Standing Pilot Gas - No auxilary
This thermostat is designed to work on the following heating and cooling systems:
Gas - Milivolt Systems
Oil - important information
This thermostat is not designed for multi-stage heat pump systems or 110/220 V baseboard heating systems.
If...
Owner's Manual - Page 6
To install your new thermostat, you will need the following supplies:
Flat-head screwdriver
Small Phillips-head screwdriver
Hammer
Electric drill and 3/16" bit
Two 1.5 Volt (AA) size alkaline batteries
6
Tools This thermostat includes two #8 slotted screws
and two wall anchors for mounting.
Owner's Manual - Page 7
The wires must be labeled prior to removal to ensure proper reconnection.
7
Do not disconnect the wires from the existing thermostat before reading these instructions. NOTICE!
Owner's Manual - Page 9
... the power to expose the wires and mounting screws.)
9 uninstalling the existing unit 1. Remove the existing thermostat cover to the back of the wall plate. Locate, but do not disconnect the wires.
(If wires are not visible, they may have multiple covers, ...
Owner's Manual - Page 10
RH / R / VR / 4
RC / VC
Y / C* / M / O
label the wire with this sticker:
24 Volt RH
24 Volt cool RC
air conditioning compressor
W / H / B G / F Y1
heating
fan heat pump compressor
Y/0 W/B
G
Y1
10 Y1 G W/B Y/0 RC RH
if your existing thermostat is marked...
Owner's Manual - Page 11
Refer to the existing terminal designation for nonbattery powered thermostats.
5. Do not let the wires slip back into the wall during disconnection. Using the provided stickers, label each wire and remove the existing wall plate.
...
Owner's Manual - Page 13
... THE WALL PLATE
1. If the existing holes do not match those on the bottom of the thermostat.
2. Remove the wall plate from the new thermostat by pressing the release tab on the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the ...
Owner's Manual - Page 15
Tap the plastic anchors into the anchors. Insert the mounting screws through the opening. installing the thermostat, cont. 4. Verify that the wall plate is visually level and securely tighten both screws.
15 Remove the wall plate and drill two 3/16"
holes where ...
Owner's Manual - Page 17
... of any excess wire length back into the wall.)
3.
Loosen, but do not have both an RH and RC wire, remove this jumper. installing the thermostat, cont. If you do not remove, the terminal screws.
Owner's Manual - Page 25
... cont. The AM/PM indicator will
flash) 2. You can change the format to adjust the setting. 3.
Press Day/Time. (AM/PM and current hour will be off when the thermostat is in 24 hour mode.
Press ...to the normal display. Press Day/Time again to the normal display.
25
The default for this thermostat setting is in a 12 hour format. You may also press Hold/Return at any time to return to...
Owner's Manual - Page 29
If you want to operate their thermostats manually, adjusting settings as desired.
29 You can either temporarily override the settings for... program: 1. Press the Up or Down buttons to enter Manual Override mode. (Release the button
when the display flashes.)
2.
Press and hold Up or Down for the current program, or permanently override all settings and adjust temperatures manually. methods ...
Owner's Manual - Page 31
..., CONT. If you want to adjust the temperature setting as desired. 4. Press the Up or Down buttons to permanently override all settings and adjust the thermostat manually: 1. methods of operation, CONT. Press and hold Up or Down for one second to the normal display.
31 Press Hold/Return until the Hold...
Owner's Manual - Page 35
... in increments of 1o F (1o C).
• After 15 seconds of operation, CONT.
3. Slide the system switch to HEAT or COOL to flash)
35 methods of inactivity during programming, the thermostat will begin to program the corresponding system.
2. Press Program to enter Program mode. (The
LCD will return to Normal Display mode.
•...
Owner's Manual - Page 39
ICONS AND FEATURES 1. will backlight the
display for more than 3 seconds will flash after changing the filter to reset the filter timer.
(Pressing the Filter button for 3...(If no button is pressed after 5 seconds, the backlight will turn off.)
Note: If the thermostat shows a Low Battery Warning, the backlight will not be affected unless the button is held for easy viewing in the dark...
Owner's Manual - Page 43
... shortage. When the batteries are detected as weak, the icon will be erased.
The thermostat will turn off until new AA alkaline batteries are installed.
43 If all battery power is left, the battery icon will flash alone on the display and your system will resume normal operation after new batteries are...
Owner's Manual - Page 45
When the thermostat is in Auto Recovery mode, the display will not operate if Permanent or Temporary holds are ... by sliding the recovery switch on .)
Press Hold/Return during the Auto Recovery process to the disable position.
(Auto Recovery will flash alternating messages of RECO and the time. ICONS AND FEATURES, cont.
5. Auto recovery calculates the time needed to adjust the temperature...
Owner's Manual - Page 47
... off until the batteries are replaced with new AA alkaline batteries. Auto cut off - The screen will flash an ERR message and shut your HVAC system has malfunctioned, the system will no longer respond to thermostat controls and the Auto cut off will have no effect.)
47 Error mode - ICONS AND FEATURES...
Similar Questions
Thermostat Flashing #2
The temperature on my Hunter Thermostat dropped to 63 degrees for no apparent reason. I changed the ...
The temperature on my Hunter Thermostat dropped to 63 degrees for no apparent reason. I changed the ...
(Posted by dc914150 1 year ago)
What Do A Blinking 4 Mean On A Hunter Thermostat 44260
44260 Hunter thermostat blinking 4 what does it mean
44260 Hunter thermostat blinking 4 what does it mean
(Posted by Rickandremodel 3 years ago)
Why Does Aux Flash On My Hunter Thermostat Model 44272
I have a programable thermostat that flashes aux all the time when the heat is on
I have a programable thermostat that flashes aux all the time when the heat is on
(Posted by dsstock205 5 years ago)
