Hunter 20578 Support Question
Hunter 20578 Support Question
Find answers below for this question about Hunter 20578.Need a Hunter 20578 manual? We have 3 online manuals for this item!
Question posted by malcumdc on February 10th, 2014
Hunter Fan Model 20578
I recently had a "fan and light control" pn 89309-01 go out on one of my three fans and can not find this part. where do I get one?
Current Answers
Related Hunter 20578 Manual Pages
Owner's Manual - Page 5
... Transmitter and Receiver...9 5 • Wiring the Fan...11 6 • Installing the Ceiling Plate Cover...13 7 • Assembling the Blades...14 8 • Activating Auto BalanceTM...15 9 • Completing Your Installation With a Bowl Light Fixture...16 10 • Removing the Light Fixture...19 11 • Operation & Maintenance...21
1 42798-01 • 12/28/09 • Hunter Fan Company
Owner's Manual - Page 6
... are missing or damaged, contact your fan to avoid damage to these instructions, and use only Hunter speed controls and accessories. For ceilings higher than one fan, keep the fan blades and blade irons (if applicable) in the world. Use only Hunter speed controls.
2 42798-01 • 12/28/09 • Hunter Fan Company We are installing more than 8 feet...
Owner's Manual - Page 7
...
If you cannot check off every item, prepare a new fan site as described on this page.
Fan Support System
• Fan attaches directly to building structure.
• Fan support system will hold full weight of the fan and light kit.
If your new Hunter fan.
Ceiling Hole
• e outlet box clearance hole is secured to airflow, such...
Owner's Manual - Page 8
... fan and light
kit.
If you to the outlet box with Section 2 • Installing the Ceiling Plate. You will use a
qualified electrician.
4 42798-01 • 12/28/09 • Hunter Fan...70. Step 3 - Install a Support Brace, If Necessary
Determine if there is positioned to the fan supply line leads and associated wall switch location are unfamiliar with two #8 x 1-1/2" wood screws and ...
Owner's Manual - Page 9
... outermost holes in the middle of the ceiling mounting plate (2).
5 42798-01 • 12/28/09 • Hunter Fan Company Drill two 9/64" pilot holes into the wood support structure through...the Ceiling Mounting Plate
2.1
2.2
CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as...
Owner's Manual - Page 10
...alignment, use the enclosed optional pipe/ball assembly,
follow Steps 3.5 - 3.9.
6
42798-01 • 12/28/09 • Hunter Fan Company
Place a flat washer (68) on each other. Tighten the screws (65) ...
For Angled Ceilings: Be sure to use slotted holes directly across from the fan. Note: Your Hunter fan comes with the pilot holes you would like to orient the ceiling mounting plate (2)...
Owner's Manual - Page 11
... unscrewing. Using the provided Allen wrench (79), loosen the setscrew (8) on the ceiling mounting plate hooks.
7
42798-01 • 12/28/09 • Hunter Fan Company the
coating prevents
the pipe/ball assembly from the fan through the ceiling mounting plate cover (3) and ceiling mounting plate cover trim ring (4). When the pipe and ball...
Owner's Manual - Page 12
...the pin from the pipe, then slide the wedge off the pipe.
8 42798-01 • 12/28/09 • Hunter Fan Company Note: The Auto BalanceTM system is designed for pipe/ball assemblies that are... 6" and shorter. If you would like to hang the fan. Pipe
3.7
Ball
Pipe Ball Screw
Optional Pipe/Ball Instructions:
Your Hunter fan comes with an optional pipe/ball assembly extension pipe.
If you ...
Owner's Manual - Page 13
..., wedge, pin, ball, and pipe ball screw, in the battery compartment.
9 42798-01 • 12/28/09 • Hunter Fan Company The DIP switches for the transmitter (87) are located on the flat surface of the...battery is still off. Screw
3.9
3 • Assembling and Hanging the Fan (continued)
Ground Wire
3.10
Optional Pipe/Ball Instructions:
Remove the screw and ground wire from the pipe.
Owner's Manual - Page 14
... -). This device may cause undesired operation.
42798-01 • 12/28/09 • Hunter Fan Company This device must accept any interference received, including interference that reads "CFL" if you are going to use incandescent bulbs.
87
4.4
199
Note: Remove the battery from the remote control transmitter if the product is subject to battery...
Owner's Manual - Page 15
... to the green ground wire (grounding) from the ceiling mounting plate and the green ground wire from the pipe/ball assembly (7).
11 42798-01 • 12/28/09 • Hunter Fan Company For all these connections use switch in accordance with national and local electrical codes and ANSI/NFPA 70. 5 • Wiring the...
Owner's Manual - Page 16
... wires and wire connectors (70), except for the white antenna wire from the receiver (marked on white tag "LIGHT OUT")
• The black wire from the fan to the edge for clear reception.
12 42798-01 • 12/28/09 • Hunter Fan Company Using the small wire connectors (70), connect the wire from the...
Owner's Manual - Page 17
...) into place.
The ceiling mounting plate
cover trim ring will flex out releasing the ceiling mounting plate cover trim ring (4).
13 42798-01 • 12/28/09 • Hunter Fan Company Should you need to align the ceiling mounting plate cover screw holes with the mounting holes on opposite sides of the ceiling...
Owner's Manual - Page 18
Slide the blade arms (44) onto the blade-to -arm screws (47) as tight as possible with a screwdriver.
14 42798-01 • 12/28/09 • Hunter Fan Company Tighten the blade-to -arm screws (47). 7 • Assembling the Blades
66
7.1
46
Squeeze the rubber blade grommets (66) into the holes in , then ...
Owner's Manual - Page 19
... red retaining screws is visible through the notch in their place and continue the installation process.
15 42798-01 • 12/28/09 • Hunter Fan Company Rotate the blades slowly until one of the fan housing using a pipe/ball assembly longer than 6 inches, leave the retaining screws in the mounting plate. Repeat this...
Owner's Manual - Page 20
...the keyhole slots in the narrow end of installing the fan with Step 9.4.
42798-01 • 12/28/09 • Hunter Fan Company Install the remaining screw into the switch housing ... to install the light fixture, proceed with an integrated light fixture assembly and an optional switch housing cap and plug button.
9 • Completing Your Installation With a Bowl Light Fixture
9.1
9.2
...
Owner's Manual - Page 21
...chains through the holes in the metal disc.
17 42798-01 • 12/28/09 • Hunter Fan Company Attach the lower switch housing to the lower plug ...holes in the lower switch housing assembly (31). 9 • Completing Your Installation With or Without a Bowl Light Fixture (cont.)
9.4
Note: Both plug connectors are properly aligned
9.5 before connecting
them through the grommet holes ...
Owner's Manual - Page 22
... end until tight. 9 • Completing Your Installation With a Bowl Light Fixture (cont.)
9.8
150
Lift the glass bowl (150) up against the glass bowl (150). You can simply mount the remote holder on the wall.
18 42798-01 • 12/28/09 • Hunter Fan Company
Align the holes in the glass bottom.
150
9.9
115...
Owner's Manual - Page 26
...in warm weather to cool the room with a direct breeze.
hunterfan.com
42798-01 • 12/28/09 • Hunter Fan Company So, you are projected to cut back on heating bills. * On...). Airflow Direction Ceiling fans work best by purchasing this purchase, you can cut air pollution by more than typical ceiling fan models. Every degree you set by a Hunter ceiling fan lets you raise the...
Parts Guide - Page 1
...1
99546-09
1
87697-03
1
97950-05
1
77325-40
11
65973-01
1
99533-00-860
1
65666-01
1
89309-01
1
99600-01
1
64349-06
1
08198-01
1
08200-01
1
73853-01
1
73854-01
1
64833-01
1
64350-01
1
65795-01
2
63756-26
1
63756-18
1
63756-19
2
74393-08
1
87333-01
Hunter Fan Company • 7130 Goodlett Farms Pkwy. #400 • Memphis, TN 38016 • www.hunterfan.com...
Similar Questions
Am Looking To Buy Fan Blades For Hunter Ceiling Fan Model 21318 Part Number 7669
(Posted by Dccantwell 1 year ago)
What Is Causing Lights On My Ceiling Fan Model #21730 Started To Blink?
(Posted by pjdaughton 10 years ago)
Need Hunter Part No. 98378.01, Light Kit Assembly, For Ceiling Fan Model 28679
Hunter says they do not make this model any longer and that they do not have part. Can you help me f...
Hunter says they do not make this model any longer and that they do not have part. Can you help me f...
(Posted by larrypricesimmons 10 years ago)
How To Access The Capacitor In Hunter Fan Model 23856
how to access the capacitor in hunter fan model 23856
how to access the capacitor in hunter fan model 23856
(Posted by trioxyys 11 years ago)
I Need A Gear Box For A Hunter Floor Fan Model # 90122a
This is a reciprocating gear box. The mounting casting (pot metal) is broken.
This is a reciprocating gear box. The mounting casting (pot metal) is broken.
(Posted by davecallahan 11 years ago)