Humax IRCI-5400 Support Question
Humax IRCI-5400 Support Question
Find answers below for this question about Humax IRCI-5400.Need a Humax IRCI-5400 manual? We have 1 online manual for this item!
Question posted by shery342 on March 12th, 2019
Problem In Irci 5400z
hello sir i have IRCI 5400Z problam is 3 dots flashing no workiqbal
Current Answers
Answer #1: Posted by waelsaidani1 on March 12th, 2019 3:33 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Three dots flashing appears on the Panel. This is due to a corrupted Channels Settings module.
Most of the time, this corruption happens when you organize your Channels such as Sorting, Define your Favorites Channels...etc using the Remote Control.
To avoid this problem, use HNFSmart program to Download your existing channels from your STB to your PC/Laptop, or get any Channels Settings file (Cyrus, PET123...) from the net, organize the channels with HNFSmart program then Upload them to your STB.
To fix the three dots flashing problem, just upload a Channels Settings file to your STB using HNFSmart.
Most of the time, this corruption happens when you organize your Channels such as Sorting, Define your Favorites Channels...etc using the Remote Control.
To avoid this problem, use HNFSmart program to Download your existing channels from your STB to your PC/Laptop, or get any Channels Settings file (Cyrus, PET123...) from the net, organize the channels with HNFSmart program then Upload them to your STB.
To fix the three dots flashing problem, just upload a Channels Settings file to your STB using HNFSmart.
Related Humax IRCI-5400 Manual Pages
User Manual - Page 2
... disconnecting the cable from the wall outlet before connecting or disconnecting the cable from the satellite dish.
EARTHING
: The LNB cable MUST BE EARTHED.
This symbol indicates important instructions accompanying...and that presents a risk of the STB. CLEANING
: Disconnect the STB from the satellite dish.
Do not expose the STB to lightening, rain or sunlight.
RISK OF ...
User Manual - Page 3
... Dolby Laboratories. The use of unofficial software. Glossary • Antenna
A device that receives, amplifies and retransmits a signal on a different frequency.
2 Includes a satellite dish and abroadband antenna. • Forward Error Correction(FEC) A system of error control for any kind of problems caused by the orientation of the electricfield vector. • Quaternary Phase Shift Keying...
User Manual - Page 7
...OUT connector on the STB and the other end to the LNB IN socket on the STB for receiving terrestrial
channels. 6. Connect one end of a RF lead to the RF OUT connector on the STB...the RF IN connector on your Hi-Fi system.
6 Connect one end of the following set-up for receiving terrestrial
channels. 4. Connect your TV. 2. Connect the coaxial cable from the AUDIO L,R sockets on the back...
User Manual - Page 8
... system to the RF IN connector on the STB. 6. Connect one end of your TV antenna to the LNB IN socket
on the STB for receiving terrestrial
channels. 7. Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the LNB connector on...
User Manual - Page 9
... analogue or digital STB and you assemble several antenna or a multi-feed equipment that has satellite signals. • Connect an antenna cable through the antenna cable.
4. When you wish ...in example displayed. 3. Connect one end of 22KHz- Connect a Satellite antenna To the digital receiver, you can connect a further Sat-receiver(for other end to the LNB 1 or LNB A input connector ...
User Manual - Page 10
... OTA. Whenever a problem is a highly sophisticated product - Do this software or, in the equipment has to release software downloading via satellite systems. Note that ...the manufacturer uses.
9 It is essential to have appropriate loader software; 2) the manufacturer decides to be found with a Dolby Digital soundtrack (see page 11) you can be received...
User Manual - Page 11
...(0~9) on the remote control unit.
2. To select the previous viewed Service, press the Recall( )
button.
10
The Help window shows the current Network information, including: Satellite Name, Frequency, Polarisation, Symbol Rate, FEC... Changing Services
To change services, do in the I-Plate, the Help window will be displayed by using the White...
User Manual - Page 17
... is pressed after selecting the highlighted parental control on the TV Guide or Information box. Enter the PIN code on the display window. (If any problem occurs when entering a PIN code, you have already reserved on the initial menu screen, a display window for entering the PIN code will be reserved. Enter...
User Manual - Page 18
... the default language for menu, audio or subtitle. 1. If you want and then
press the button to the connection of Main Menu
4. Guide of the receiver and external units.
Use the buttons to move to customise, add a new service and displays the state of current service will be changed depending on...
User Manual - Page 19
... Time(standby mode) can also be used as the standardised time for the I-Plate, TV Guide, Wakeup and Sleep Timer. The time setting will not work. If you select "Disabled", then the other timers will be set the Current Time, enter the Offset value using the standardised information of timer programming.
User Manual - Page 25
... the button to access the Service Searching menu as OTA target satellite,
automatic detection of the OTA target satellite might not work properly if you access the Parental Control or Service Organising menu. Satellite Name Selects the Satellite Name that are 32 possible Antenna Setting for selection in other service searching menus. Note : In case...
User Manual - Page 28
... skip all scrambled services. • When the found services are output through LNB line
Symbol Rate Inputs the Symbol Rate of the entered parameters. The Satellite Name helps you want to find. Antenna Alternative Select the target antenna for reference and cannot be changed on the remote control unit. Guide of...
User Manual - Page 30
... symbol rate list is changed according to the Detail mode.
29
Note : The user should select the Satellite name in the selected position and then the symbol rate disappears.
The range of the selected satellite without inputting the extra frequency. Then press the
and the
Red( )button to add or change the...
User Manual - Page 31
...Do not turn on the service provider. Common Interface
You can download and upgrade the software of this STB via ASTRA1 satellite when the software of the current service and is help to start Automatic Search. Note : If CAM is released.
...Search to return Service Search menu.
4-4. The picture searches with Antenna Alternative of the picture. Satellite Name is as follows:
1.
User Manual - Page 33
... DiSEqC 1.2.
In Installer mode this is available for better reception. Reset : Resets all stored positions of a satellite manually. Setting your Receiver for DiSEqC 1.2
You must set your receiver up a separate antenna alternative for services on the Satellite Setting menu. Select Antenna Setting option and press button,
to
display the Service Searching menu.
3. The option...
User Manual - Page 34
... Control option and use the
buttons to change the value to start storing services for the various satellites(see the Service Searching
menu.
4. You should now see 5 onwards).
4. You should be ... above).
3. To set your motor).
8. Initial Satellite Position Search
This is installed correctly with the
calibrations adjusted for your receiver up to move your
dish.)
6.
User Manual - Page 35
...the
buttons to display the Service
Searching menu.
2. When you have the best position of the satellite should register a signal once. During the move it will be unique to this to store the...see 3 above). Select the Manual Search option and press the button, to display the Satellite Settings menu.
5.
This transponder information should move the motor as far west as your ...
User Manual - Page 36
... entered all these will be lost.
7. When you change to use your new selected satellite, Do as follows ;
1. Do as follows;
1. To search for the
services transmitted from a different satellite, you search new services, please refer to receive the new service.
35
Select Service Searching from the Main Menu and press the
button...
User Manual - Page 40
... 60 Mbit/s Max 4:3, 16:9 720 x 576 MPEG/MusiCam Layer I & II Single channel/Dual channel/Joint stereo/Stereo 32, 44.1 and 48 KHz
Memory
Main Processor Flash Memory Graphic(MPEG) & System DRAM
TMIPS R3930(81MHz) 3 Mbyte 4 Mbyte
You can use a special antenna switch with the picture quality of digital TV programmes. The...
Similar Questions
Problem With My Satellite Receiver
my humax ir free (ir.deto) when I switched off the power it gave continuous system initializing scre...
my humax ir free (ir.deto) when I switched off the power it gave continuous system initializing scre...
(Posted by mkaliouby 9 years ago)
My Satellite Receiver Irci 5400z Is Not Working
where i can get a technician to repair the receiver in sydney (nsw) if is posible in the western sub...
where i can get a technician to repair the receiver in sydney (nsw) if is posible in the western sub...
(Posted by angelgarcia1948 10 years ago)
Not Working On Some Channels After Dele All..
I was using my box for B sky B,Badr and Turksat 42e.After i deleted all channels by mistake and try ...
I was using my box for B sky B,Badr and Turksat 42e.After i deleted all channels by mistake and try ...
(Posted by mordechaj111 11 years ago)
My Humax Irci-5400 Remote Control Think Is Faulty.
It only display the volume as soon I put the batteries in. Every button you press nothing happens. I...
It only display the volume as soon I put the batteries in. Every button you press nothing happens. I...
(Posted by jvxaghra 11 years ago)