Hoover H3000 Support Question
Hoover H3000 Support Question
Find answers below for this question about Hoover H3000.Need a Hoover H3000 manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by freginold on September 22nd, 2015 8:29 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
Hello, you can see how to remove and replace the brush assembly on pages 10-11 of the user manual. If you don't have the user manual, you can download it here.
Related Hoover H3000 Manual Pages
Manual - Page 1
... outlet locations (U.S. If you should happen to need assistance during assembly or operation:
Visit us online at www.hoover.com to speak with SpinScrub™ Brushes
The Hard Floor Cleaner
Thank you (click on the "Service" button) or
Call 1-800-944-9200 for selecting a HOOVER product. PLEASE DO NOT RETURN THIS...
Manual - Page 2
... by or near children. They may damage the cleaner.
• Do not put any opening blocked; If an extension cord is not working as described in the instructions. Do not expose machine... spills 10
If You Have a Problem 12 Service 12
Important Safeguards 2 Maintenance 10-11
Cleaning the brushes .........10-11 Cleaning the nozzle 11 Warranty 13
© 2001 The Hoover Company www.hoover.com
2...
Manual - Page 3
... Hoover Factory Service Center or in place by a qualified
D
F
G
E
electrician. Upper handle C. Brush block E.
Check with a qualified electrician or service person if you (click on the list provided with a ...: In Canada, the use on latch (A) and remove clean solution tank from the adapter must be held in the Yellow Pages under "Vacuum Cleaners - Do not modify the plug provided with ...
Manual - Page 4
... the cord out of cleaner.
To install brushes, place handle in place.
1-6
1-7
E
1-8
D
Replace clean solution tank by positioning bottom first.
Tighten screw with opening (H) on the handle.
4 You will hear a "click" when the switch rod is in upright position. Remove cardboard packing insert from squeegee area on brush block with washer in place.
1-11
I ), located...
Manual - Page 5
... on pedal (A) to lower handle to allow convenient operation. Brush release buttons: Remove brushes for household use
2-1
1
2
3
4
5
6
18...
7 19
9
8
10
17
14
12
17
13
11
14
15 16
13
20
The assembled cleaner will look like this drawing. 1. Squeegee 17. Cord hooks: Top hook rotates
for wet pickup and dry vacuuming...
Manual - Page 6
...floors, inspect floor surface for complete cleaner setup instructions.
To remove tank, press down to clean" section for dry vacuuming. See "How to fill
Disconnect cleaner from electrical outlet....damage to choose either the WET or DRY setting.
2-7
G
Brush Control Switch
The brush control switch (G) turns the brushes on pedal to wood floors, follow the flooring manufacturer's cleaning ...
Manual - Page 7
... latch and snap tank into tank. There are two reasons the shut-off .
For best results, use with uneven side against ledge (K) as shown.
2-14
Replace cap.
Check for worn spots or joint separations before using, as these concentrates have been specifically formulated to serve as vinyl, ceramic and other tiles...
Manual - Page 8
...cleaned by either brushing or tapping the filter. The tank lid contains a washable, reusable filter. To replace lid, align tab (P) on lid with hole on the filter screen (O) in place.
Remove debris from electrical ...Turn cleaner OFF and disconnect from screen. How to be emptied after dry vacuuming and before wet operation.
It may also be rinsed for satisfactory performance, it...
Manual - Page 9
Follow the chart to operating position; OPERATION Dry Vacuuming
BRUSH CONTROL SWITCH WET/DRY PEDAL
"Wet/Dry Pickup" (UP)
Dry Pickup
Wet Cleaning
"Wet ... a loss of wax in your cleaner.
4.
Simply move wet control switch down to help prevent streaking.
Squeeze trigger to remove loose dirt, hair and debris. 2. Do not use any type of suction (see "Automatic Shut-Off", page 7).
...
Manual - Page 10
...' Cleaner to pick up detergents that contain pine or solvent based ingredients.
4. Tilt cleaner back slightly and remove brush assembly (B).
CAUTION: To prevent damage to pick up flammable or combustible liquids or chemicals. Step on handle ... cleaner on sealed wood floors, inspect floor surface for Dry Vacuuming operation and vacuum floor (see "Automatic Shut-Off", Page 7).
Manual - Page 11
... in recovery tank lid to dry. • Set the cleaner for easy cleaning.
4-6
4-7
4-8
F E
H
I ) on brush block with a damp cloth. Rinse nozzle under running water.
To replace nozzle, make sure latches are out.
The cleaner's nozzle (E) can be removed for "Dry Vacuuming" (pedal to "DRY" and Wet Control switch up). • Make sure that it rests...
Manual - Page 12
...fuse or breaker.
• Blown fuse/tripped breaker • Replace fuse/reset breaker. off engaged. • Remove and empty recovery tank.
• Filter or filter lid missing ...brushes continue to stall and the breaker trips again, clean the brushes to The Hoover Company in front of Reckitt Benckiser Inc.
12 only). Do not send your cleaner by :
• checking the Yellow Pages under "Vacuum...
Similar Questions
Can I Buy A Replacement Battery For This Vacuum?
I need a new battery
I need a new battery
(Posted by pmh5555 9 months ago)
H3000 Wont Dispense Liquid
The H3000 won't dispense cleaning liquid when in wet mode and trigger depressed.
The H3000 won't dispense cleaning liquid when in wet mode and trigger depressed.
(Posted by tehambleton 7 years ago)
