Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by alancody on January 19th, 2012
Does A Rth 2310 B Have A Heat Anticipator Setting?
furnace runs for a minute quits for a couple then starts this cycle over and over
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... are here to help. Just follow the simple step-by-step instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system.
Owner's Manual - Page 3
... • a millivolt system • a central heating and cooling system
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot...
Owner's Manual - Page 4
...: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet. Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
...Do not use non-connected wires.
IGNORE WIRE COLORS: Use terminal screw designations to your old thermostat or are attached to a terminal marked C or C1, they will not be connected to ...the old wallplate only after all wires are not attached to your new thermostat. If any wires are labeled. RTH2310 Programmable Thermostat
3 Identify Wires
3. Wrap the bare metal end of these wires ...
Owner's Manual - Page 6
Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
Labels don't match? If a wire does not match any excess wire back into the wall opening.
RTH2310 Programmable...
Owner's Manual - Page 9
RTH2310 Programmable Thermostat
7 Specify Furnace Type
6. HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
... the batteries as shown. By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. You will display the ambient temperature once it is installed on the wall. It is 70 °F (21...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are shown in U.S.A. Rev. 03-11 Printed in bold and underlined.
2 See page 3 of Operating Manual.
3 Use the system switch to the next function, briefly ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
Does Rth 7000 Have Heat Anticipator Adjustment?
My thermostat doesn't read temperature properly. When inside tem is 77 and rising, it doesn't show 7...
My thermostat doesn't read temperature properly. When inside tem is 77 and rising, it doesn't show 7...
(Posted by alan17852 9 years ago)
Video Of How To Set A Honeywell Thermostat Rth2310b
(Posted by karaSnie 10 years ago)
Anticipator Setting
Currently have a Honeywell T8196A thermostat and using it on a gas heat (forced air) and cooling sys...
Currently have a Honeywell T8196A thermostat and using it on a gas heat (forced air) and cooling sys...
(Posted by Sojerzboy 12 years ago)