Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by rick33903 on March 1st, 2014
Cannot Change Time And Pushing Arrows Up Or Down Does Not Change Temperature.
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... are here to help. Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type...
Owner's Manual - Page 3
... systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 RTH2310 Programmable Thermostat
Identify System Type
1.
This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of...
Owner's Manual - Page 4
... waste management authority for instructions regarding recycling and proper disposal.
3 Contact your old thermostat in the trash if it contains mercury in a sealed tube. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet.
Owner's Manual - Page 5
... to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled.
Wrap the wires around a pencil to identify wires. RTH2310 Programmable Thermostat
Identify Wires
3. If any wires are not attached to your new thermostat.
Do not use C or C1 wires
Identify and label each of these wires...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
....
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
If a wire does not match any excess wire back into the wall opening.
Owner's Manual - Page 9
RTH2310 Programmable Thermostat
Specify Furnace Type
6. HE Place the jumper to the G terminal.
Set the Jumper J2, on the back of the thermostat, if you have a gas or oil furnace. J2 jumper
HG Leave the jumper in this position if you have connected a wire to this factory-set position if you have an electric furnace.
8
Owner's Manual - Page 10
...
sound. Observe the
polarity. 3) Reinstall the battery cover. It is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. After the batteries are holding the thermostat. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or... 6=10 min
09-08
11
Printed in U.S.A. Quick Installation Guide
System Setup
9.
1) Press both and buttons simultaneously.
3) To change the setting, press the or button.
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do I Get The Thermostat To Change Temperatures?
my thermostat is staying at 68 and I want to lower the temp.( I changed the batteries
my thermostat is staying at 68 and I want to lower the temp.( I changed the batteries
(Posted by hpomahac 4 months ago)
How To Change A Battery In A 7 Day Programable Thermostat
(Posted by buddy2004 11 years ago)
I Changed My Batteries With Fresh New Ones. Now My Backlit Display Is Not Visibl
Is there a reset button?
Is there a reset button?
(Posted by cdavies 13 years ago)