Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by calljameshere on March 22nd, 2014
Batteries Fail Within 24 Hours
Suddenly battery life in my 2310 has gone fron 2-3 years to 1-2days. Then the low battery warning starts to flash, and the back-light stops working. I am using more than one pair of rechargeables . . .
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...; Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat. Set the system.
We are here to help. Call 1-800-468-1502.
1 Do you need assistance? Quick Installation Guide
Installation is Easy
Your...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2
This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
Do not remove wallplate yet.
Contact your old thermostat in the trash if it contains mercury in a sealed tube. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old...
Owner's Manual - Page 5
... screw designations to your new thermostat. Do not use non-connected wires. Disconnect wires and remove the old wallplate only after all wires are attached to a... tape, so it cannot touch and short other wires. If any wires are not attached to your old thermostat or are labeled. Do not use C or C1 wires
Identify and label each of each wire.
Wrap the wires around a pencil to prevent...
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
...'t match? Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Owner's Manual - Page 8
If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below. Wrap bare end of wire with electrical tape. Quick Installation Guide
Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7
Do not use C, X or B.
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 HE Place the jumper to the G terminal.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
After the batteries are holding the thermostat. The thermostat will hear a clicking
sound. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. Afterwards, the screen displays the actual temperature. Observe the
polarity. 3) Reinstall the battery cover. By default, the setpoint is installed on the wall. You will...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...).
5 The corresponding cooling cycle lengths are shown in U.S.A. DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 min, 6=10 min
09-08
11...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
Display Goes Blank
twice the display has gone blank then come back on when i press keys. both times needed to reset the...
twice the display has gone blank then come back on when i press keys. both times needed to reset the...
(Posted by garywhiteman 9 years ago)
Thermostat Stopped Working
Air and Cooling thermostat quit working. It was working fine and I turned it off for a few hrs, and ...
Air and Cooling thermostat quit working. It was working fine and I turned it off for a few hrs, and ...
(Posted by carolyle7 10 years ago)
When The Thermostat Stops Working Will The Unit, Ac/heat Pump, Stop Also.
The thermostat went blank and nothinf responds; the fan, ac, nor heat pump, will work.
The thermostat went blank and nothinf responds; the fan, ac, nor heat pump, will work.
(Posted by jimbodawg 12 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)