Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by charliesdevil73 on January 22nd, 2012
Setting A Jumper
What does it mean to set a jumper?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the...batteries. Install the thermostat. Set the system.
Do you need assistance? Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for fast and easy installation....
Owner's Manual - Page 3
...
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi...
Owner's Manual - Page 4
Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Contact your old thermostat in the trash if it contains mercury in a sealed tube. MERCURY NOTICE: Do not put your local waste management authority for...
Owner's Manual - Page 5
RTH2310 Programmable Thermostat
Identify Wires
3.
Do not use non-connected wires. Wrap the wires around a pencil to your old thermostat or are attached to a terminal marked C or C1,...and remove the old wallplate only after all wires are not attached to your new thermostat.
If any wires are labeled. IGNORE WIRE COLORS: Use terminal screw designations to identify wires....
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors.
Owner's Manual - Page 7
Labels don't match? RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
If a wire does not match any excess wire back into the wall opening.
Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert ...
Owner's Manual - Page 8
Wrap bare end of wire with electrical tape. If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below. Quick Installation Guide
Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7
Do not use C, X or B.
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have a gas or oil furnace. HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this position if you have connected a wire to this factory-set position if you have an electric furnace.
8
RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
After the batteries are holding the thermostat. It is 70 °F (21 °C).
9 You will display the ambient...By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery ...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace), 4=15 min (gas ... switch to the next function, briefly press both and buttons simultaneously.
3) To change the setting, press the or button.
Quick Installation Guide
System Setup
9.
1) Press both ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
Adjustment Lever Setting In Honeywell Ct30 Thermostat
Can someone please suggest the correct adjustment lever setting in the Honeywell CT30 thermostat for...
Can someone please suggest the correct adjustment lever setting in the Honeywell CT30 thermostat for...
(Posted by akiselyuk 7 years ago)
How To Set The J2 Jumper Honeywell Rth230b Thermostat
(Posted by MATAZ 10 years ago)
How To Set Clock To 12 Hours
Somehow system stopped while we were away. Now the one (out of three) thermostat went to a 24 hrs cl...
Somehow system stopped while we were away. Now the one (out of three) thermostat went to a 24 hrs cl...
(Posted by skiqueen58 11 years ago)
Trane Heatpump Does Not Come On. Settings Per Manual And Nothing Happens.
(Posted by hlancaster 12 years ago)