Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by jwsbuchner on May 15th, 2012
We Have An Old Honey Well Mercury Thermostat
If we set the thermostat temperture on 18 degrees it goes on to 22 degrees so we have to reset it to get the right temperture
can you please help us how to do that or give us an manuel to download
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
....
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat. Set the system.
Quick Installation Guide
Installation is Easy
Your...
Owner's Manual - Page 3
... are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
RTH2310 Programmable Thermostat
Identify System Type
1.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat...
Owner's Manual - Page 4
... in the trash if it contains mercury in a sealed tube. Do not remove wallplate yet.
Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3
Owner's Manual - Page 5
...each wire.
Wrap the wires around a pencil to your new thermostat. Do not use non-connected wires.
Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked ...prevent them from falling though the wall opening.
4 If any wires are not attached to your old thermostat or are labeled. Do not use C or C1 wires
Identify and label each of these ...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 If a wire does not match any excess wire back into the wall opening...
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have an electric furnace.
8
HE Place the jumper to the G terminal. J2 jumper
HG Leave the jumper in this factory-set position if you have connected a wire to this position if you have a gas or oil furnace. RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
.... Afterwards, the screen displays the actual temperature. It is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. By default, the setpoint is installed on the wall. Quick Installation Guide
Install Batteries
7.
1) Pull out the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 min, 6=10 min
09-08
11
Printed in bold and ... Use the system switch to switch between the two parameters.
4 For optimal heating control, use the setting that matches your system as follows: 2=30 min (steam, gravity), 3=20 min (hot water,...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Honeywell Mercury Thermostat
don't know where the Red jumper wire goes, My unit will not shut off can you help?
don't know where the Red jumper wire goes, My unit will not shut off can you help?
(Posted by tjp3v3y 12 years ago)
How To Stop Thermostat Chirping
My thermostat won't stop chirping. I replaced the batteries. I don't know the model but it is 3 yrs ...
My thermostat won't stop chirping. I replaced the batteries. I don't know the model but it is 3 yrs ...
(Posted by pauljohnson 12 years ago)