Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by Anonymous-44197 on November 30th, 2011
The Heat Only Works When It's In The Fan Position...does Not Work On Auto.
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... fast and easy installation. Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type...
Owner's Manual - Page 3
... systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type or if you have...
Owner's Manual - Page 4
... wallplate yet.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
RTH2310 Programmable Thermostat
Identify Wires
3. Do not use non-connected wires.
Wrap the wires around a pencil to identify wires....though the wall opening.
4 Wrap the bare metal end of each wire.
If any wires are not attached to your old thermostat or are labeled. Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1...
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
Labels don't match? If a wire does not match any excess wire back into the wall opening. RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) ...
Owner's Manual - Page 9
HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this factory-set position if you have connected a wire to this position if you have a gas or oil furnace.
RTH2310 Programmable Thermostat
Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have an electric furnace.
8
Owner's Manual - Page 10
... default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking
sound. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. You will...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5... or exit the setup menu.
2) To advance to switch between the two parameters.
4 For optimal heating control, use the setting that matches your system as follows: 2=30 min, 3=20 min, 4=15...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
Batteries Fail Within 24 Hours
Suddenly battery life in my 2310 has gone fron 2-3 years to 1-2days. Then the low battery warning st...
Suddenly battery life in my 2310 has gone fron 2-3 years to 1-2days. Then the low battery warning st...
(Posted by calljameshere 10 years ago)
I Have Rth7500. Sytem Only Shows Heat, Off, Cool. It Does Not Show Auto.
(Posted by fxbrowne 12 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)