Honeywell RCWL300A Support Question
Honeywell RCWL300A Support Question
Find answers below for this question about Honeywell RCWL300A.Need a Honeywell RCWL300A manual? We have 1 online manual for this item!
Question posted by asalter3 on August 26th, 2011
Compatibility With Existing Door Bell Chimes
Does this system work with existing door bell systems. Can i hook this up to my existing door bell, and remotely hear it in my basement. I want to use the existing door bell setup, and door bell device already mounted at my front door, and the existing security system.
Current Answers
Related Honeywell RCWL300A Manual Pages
Owner's Manual - Page 2
Installation Instructions
Contents Checking pack contents 1 Safety 2 Quick start 2 Open bell push 3 Fit the push battery 3 Fit the chime battery 4 Sliding window 4 Volume control 5 Use of icons 6 Programming procedures 7 Recall function 8 Chime sounds 8 Mount bell push 8 Chime position 9 Troubleshooting 10 Specifications 12 Disposal and recycling 12 Declaration 13 Guarantee 13
...
Owner's Manual - Page 3
...instructions to ensure correct installation and use. Please use the following parts:
• Chime • Wall mounting bracket • Bell push • CR2032 battery for bell push • 2 x fixing screws for push • 2 x fixing screws for choosing this Honeywell product.
RCWL300A
Premium Portable Wirefree Chime with Push
Thank you for chime • 2 x wall plugs • Adhesive...
Owner's Manual - Page 4
... proceeding with the chime.
Quick Start
The bell push supplied with this kit is advisable if in walls, check for hidden electricity cables and water pipes. If you have additional pushes or you want to assign a different icon to your push, you will need to follow the manufacturer's advice when using power tools and...
Owner's Manual - Page 5
Ensure the face marked '+' is uppermost (Fig. 2).
A
Fig. 1
M27199
+ CR2032
Fig. 2
CR2032
+
M27153
69-2109EFS-05 Carefully lever the cover and base apart (Fig. 1). Open the Bell Push
Insert a flat bladed screwdriver into the slot A at the base of the push. RCWL300A Fit the Push Battery
Insert the CR2032 coin cell.
Owner's Manual - Page 6
Installation Instructions
Fit the Chime Batteries
To remove the chime battery cover, press at point B and slide the cover back 1/4 in. (5 mm), then lift off. Observe polarity as marked inside the battery compartment. Insert 3 x LR6 'AA' alkaline batteries (not supplied).
B
B
Fig. 3
M27200
69-2109EFS-05
M27201 Sliding Window
Release the catch (B) and slide open the window.
Owner's Manual - Page 7
After you have tested your system, adjust to mid-point. VOLUME CONTROL
RCWL300A
M27202
69-2109EFS-05
Volume Control
The volume control is behind the sliding window on the front of the chime. Initially, set the control to the desired volume.
Owner's Manual - Page 8
...-adhesive, supplied in a different order.
They can be changed, if required, by a bell push or another compatible device. MAIN DOOR
BACK ALERT DOOR SYMBOL
Use the Programming procedure to show which device has activated it. An icon will illuminate when the chime is intended for bell pushes. The chime supports 3 icons. The 'Main door' and 'Back door' icons are also included.
Owner's Manual - Page 9
... lit, release the button.
• While the Icon you want to remove a push from the
of your push. RCWL300A
Programming Procedure
Learn Procedure
Unlearn Procedure
To enable your chime to learn the identity If you have selected is lit, operate your bell push:
chime's memory:
• Press the l button and keep it pressed. The Icon...
Owner's Manual - Page 10
... until the tune you want plays. TOP
Fig. 6
69-2109EFS-05
M27155
While the Icon is flashing, press the button. Recall Function
A short push of the l button will change . Chime Sounds
To hear the chime sounds without operating the bell push, press the button.
Avoid mounting to metal structures.
Mount the Push Mount using either the double-sided adhesive...
Owner's Manual - Page 11
Fig. 7
M27203
69-2109EFS-05 The Chime hooks onto the wall bracket as illustrated.
RCWL300A
Chime Position
The Chime can be free standing or wall mounted using the wall mounting bracket provided. If wall mounting is preferred, screw the bracket to the wall (see Fig 7).
Owner's Manual - Page 12
... not work... • Check that the batteries are programming has already been learned by the chime. • If you are the correct type, LR6 'AA' cells. Only use the un-learn mode... • The push you want to change the Icon associated with correct polarity. • The chime could be out of range of the bell...
Owner's Manual - Page 13
... need to be replaced more often. Replace every 12-18 months.
RCWL300A
Troubleshooting
The chime does not sound... • Check that affects your chime. • Walls and ceilings will reduce the range. • Weak batteries will flash every 5 seconds. Avoid mounting the push or chime on or near metal structures. • Other equipment can reduce...
Owner's Manual - Page 14
Installation Instructions
Specifications
Specification Operating Temperature
RF Frequency US/Canada Range (open field) Sound Level (typical) RF Power Battery Type Battery Life (5 activations/day) Rain proof
Chime 32°F to 104°F 0ºC to 40ºC 916.8 MHz 225 ft. (69 m) 80dBA @ 3 ft. (1m) LR6 12 months N/A
Bell push 14°F to 104°F -10ºC to 40ºC 916.8 MHz See Chime
Owner's Manual - Page 15
... for 1 year from the date of the FCC rules and Industrial Canada standards. This device operation is required: this does not affect your product call the Honeywell help line at 1-800-468-1502.
13
69-2109EFS-05 RCWL300A
Declaration
Honeywell hereby declares that may cause undesired operation. Guarantee
Honeywell guarantees this product...
Similar Questions
Can't Get It To Chime. Attached The Two Wires As Directed But No Chime.
can not get the new wired door bell to chime. I connected the two wires as directed but nothing happ...
can not get the new wired door bell to chime. I connected the two wires as directed but nothing happ...
(Posted by Eleanorhawking 7 years ago)
Wireless Chime 51372sl Rev A
my bell stopped working and i replaced the batteries in both parts of the system. After changing the...
my bell stopped working and i replaced the batteries in both parts of the system. After changing the...
(Posted by rjappel 7 years ago)
How Do I Connect This To An Existing Door Contact Sensors?
I have an existing door sensors (do not know manufacturer but was left over from Cox Home Security)....
I have an existing door sensors (do not know manufacturer but was left over from Cox Home Security)....
(Posted by Anonymous-124996 10 years ago)
Wiring My Honeywell Door Bell Rcw35/25
My previous doorbell had 3 terminals, the terminal in the middle had 2 wires (black and white) twist...
My previous doorbell had 3 terminals, the terminal in the middle had 2 wires (black and white) twist...
(Posted by jadipiaz 11 years ago)
Wireless Door Bell Not Working
We have a Hoenywell portable plus chime door bell. the button outside works when it wants to, and us...
We have a Hoenywell portable plus chime door bell. the button outside works when it wants to, and us...
(Posted by daw56 12 years ago)