Home » Honeywell » Thermostats » Honeywell CT87N

Honeywell CT87N Support Question

Find answers below for this question about Honeywell CT87N.
Need a Honeywell CT87N manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by jackkuusisto on June 19th, 2021

Sealed Cycle Switches

my Honeywell ct87n non-programmable thermostat appears to have the cycle switches sealed with some kind of film. Can't adjust them as is. Do I scrape the film off?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on June 19th, 2021 7:42 PM

SonuKumar

Member since:
May 9th, 2021

Points: 16,604,800

100
points

https://www.manualslib.com/manual/376400/Honeywell-Ct87n.html

https://www.youtube.com/watch?v=WYqK-aQqWfw

https://www.youtube.com/watch?v=f_6-_XfTcAc

https://www.youtube.com/watch?v=b-WYdwlVy6s

https://www.youtube.com/watch?v=aR78HkIhj28

you would be able to understand, how to remove old switches :

Please acceptance my work bwlow with the click button

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Honeywell CT87N Manual Pages

Owner's Manual - Page 1

... in place. Is there a sealed tube containing mercury? Registered Trademark. Patents 7,159,789; 7,159,790; 7,476,988 and other patents pending. Copyright © 2009, Honeywell International Inc. Old thermostat Cover ® U.S. If so, see mercury notice below. U.S. MERCURY NOTICE If your old thermostat contains mercury, contact your old thermostat CAUTION: TURN OFF POWER Turn...

Owner's Manual - Page 2

... 1. Do not let wires fall into wall opening . As you may have purchased the wrong replacement thermostat. IGNORE WIRE COLORS: Use only letter designations to disconnect wires one by one. Level base if desired. 3. CT87N Easy-To-SeeTM • Owner's Manual Label wires and remove old wallplate Use a screwdriver to identify wire...

Owner's Manual - Page 3

.... 3. Check level if desired. 4. Pull wires through coverplate and subbase, position over anchors, then insert and tighten mounting screws. Position coverplate on thermostat, see table below. Large-print subbase switch labels Subbase Coverplate Wiring 1. If labels do not use. [3] Do not use [3] [1] If wires will be connected to loosen screw terminals, insert...

Owner's Manual - Page 4

... for heat, if a fan wire is connected to the G terminal.) Cycle rate settings E F Move the cycle rate switches to the proper setting for heat). Align the slots on the base with tabs on the thermostat, then push gently until the thermostat snaps into place. 2. CT87N Easy-To-SeeTM • Owner's Manual Fan operation settings Move the...

Owner's Manual - Page 5

...does not cover removal or reinstallation costs. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES ...Honeywell Lim- Fan switch • On: Fan runs continuously. • Auto: Fan runs only when heating or cooling system is adjusted. Honeywell's sole responsibility shall be to be defective or malfunctions, Honeywell...

Owner's Manual - Page 16

...;Necesita ayuda? Registered Trademark. © 2009 Honeywell International Inc. 69-1919EFS-04 M.S. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com Printed in U.S.A. on recycled paper containing at 1-800-468-1502 Besoin d'aide? CT87N Easy-To-SeeTM • Owner's Manual...