2006 Honda Accord Support Question
2006 Honda Accord Support Question
Find answers below for this question about 2006 Honda Accord.Need a 2006 Honda Accord manual? We have 1 online manual for this item!
Question posted by lowu on October 18th, 2014
How To Remove The Boot Lid Trim Clip?
The person who posted this question about this Honda automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Manual Pages
Owner's Manual - Page 15
... belt can cause serious injury or death in a crash. Check that the belt rests across your hips, then pull up on the belt again to remove any slack, then check that the belt is securely latched.
Owner's Manual - Page 31
... seat. This must be replaced. Airbag Service Your airbag systems are virtually maintenance free, and there are operating properly.
32 Even if your vehicle to remove or replace any airbag by yourself. If a front airbag inflates, the seat belt tensioners must ride in front, move the seat as far to severe...
Owner's Manual - Page 32
... contact Honda Automobile Customer Service at (800) 999-1009.
33 If it is necessary to remove or modify a front seat to accommodate a person with airbag components or wiring for any reason...make the
driver's seat position sensor or the front passenger's weight sensors ineffective. Do not remove or modify a front seat without consulting your airbags.
This could cause
or covering front ...
Owner's Manual - Page 45
...part of the belt near the buckle, and pull up on the back of the seat while pulling up to remove any slack from side-to-side to put weight on the child seat, or push on the belt.
5.... Remember, if the lap part of the belt. To remove slack, it to stay upright during normal driving maneuvers. Push and pull the child seat forward and from the ...
Owner's Manual - Page 52
... potential hazards that could cause serious injury or death. If a label comes off or becomes hard to read (except for a replacement. dashboard label which is removed by the owner), contact your dealer for the U.S. HOOD
U.S. models
SUN VISOR
U.S. models Canadian models
Canadian models
RADIATOR CAP
53
Read these labels carefully. models...
Owner's Manual - Page 68
... . This feature activates if you unlock the door, but do not open , you remove the key from the ignition switch and closing the driver's door. With the driver's door open it within 15 ...seconds of removing the key from the ignition switch with the headlight switch on with reduced brightness when you set...
Owner's Manual - Page 73
... and you cannot start . This device complies with Part 15 of the device. Instruments and Controls
75 Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it . As required by the party responsible for a few seconds, then go out. Do not attempt to operate the equipment. Operation is...
Owner's Manual - Page 74
... as a test when you must be in Park, and you turn the key. The ignition switch has four positions: LOCK (0), ACCESSORY (I ) You can insert or remove the key only in this position only to ON (II). ACCESSORY (I ), ON (II), START (III).
76 Several of the lights on the instrument panel come...
Owner's Manual - Page 75
.... Each front door has a power door lock master switch. Push down , and close the door. Removing the key from the ignition switch only when parked. To unlock only the driver's door, insert the ...key, turn it clockwise, and release it up to lock the door and pull it . Remove the key from the ignition switch while driving locks the steering.
If your vehicle has an automatic ...
Owner's Manual - Page 78
Do not immerse the transmitter in any liquid. Battery type: CR1616
SCREW
To replace the battery: 1. Remove the screw at the base of the transmitter with your dealer. Separate the transmitter by your fingernail.
80 Remote Transmitter
Remote Transmitter Care Replacing the ...
Owner's Manual - Page 79
... note the polarity. Operation is subject to operate the equipment. Install the parts in reverse order. This device complies with Part 15 of the device. Remove the old battery from the keypad by releasing the two tabs on the cover.
81 As required by the party responsible for compliance could void...
Owner's Manual - Page 80
...'s seat. Lock the trunk release lever with the master key. See Carbon Monoxide Hazard on the trunk lid.
Also make sure the trunk pass-through cover is locked (see page 89 ). 2. Give the person...page 165 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to the left of the following ways: Pull up on the ...
Owner's Manual - Page 86
Turn the key clockwise, pull down the seat-back from the guide. To lock the seat-back upright, push it is latched in place by removing the belt from inside the vehicle, insert the master key in the lock on the top of the seat.
88 To release the seat-back ...
Owner's Manual - Page 94
Remove the support rod from the clip and swing the sun visor toward the side window.
To use a vanity mirror on when you pull up the cover. Sun Visor, Vanity Mirror
Sun ...
Owner's Manual - Page 155
... above the fender, then press down firmly with your hands. Put the support rod back into its clip and insert the end into the hole on the front of the way and hold it up slightly...) above the fender, then let it drop. Make sure it is securely latched. Lower the hood to remove the support rod from the hole. Make sure it is securely latched.
6-cylinder models
4-cylinder models
6-cylinder...
Owner's Manual - Page 216
...start the engine, turn the steering wheel all the way to remove the two holding clips from the fender and bumper. 4. Remove the bulb by squeezing the connector to the right. 2. Remove the electrical connector from the bulb by turning it approximately one...cover. Push the electrical connector onto the bulb. 6. Lights
Low Beam Headlight
BULB HOLDING CLIPS
TAB 6-cylinder models
BULB
5.
Owner's Manual - Page 217
...engine. BULB
Replacing the Front Side Marker/ Turn Signal and Parking Light Bulb
HOLDING CLIPS
Maintenance
1. Turn on the center. To change the driver's side bulb, turn ...by pushing on the headlights to remove the two holding clips. Install the two holding clips from the inner fender.
3.
Put the inner fender cover in place. 7. Remove the socket from the fender and...
Owner's Manual - Page 218
... burned out bulb, push it in place. Install the new bulb and turn it clockwise to lock it in place. 7. Remove the holding clip by turning it clockwise until it bottoms, and reinstall the socket into the headlight assembly. Push a new bulb straight into the socket until it in ...
Owner's Manual - Page 219
... socket, and reinstall the socket into position. 8. Test the light. 7. Push the trunk lid trim back into the light assembly. 6. Open the trunk. 2. 6-cylinder models Remove the trim clips from the right or left corner of the trunk lid trim to expose the bulbs. 4. Remove the socket by carefully prying them using a small, flat-tip screwdriver wrapped with...
Owner's Manual - Page 253
...thing you and take it , push the tabs as shown.
Taking Care of its hinges. To remove the fuse box lid, pull it toward you should check for is not the cause. Turn the ignition switch to ... first, but check all other accessories are off. 2. Remove the cover from the chart on pages 260 and 261 , or the diagram on the fuse box lid, which fuse or fuses control that a blown fuse is...
Similar Questions
How To Remove Cover Front Seat 2009 Honda Accord
(Posted by klershellm 10 years ago)
I Am Trying To Remove The Idle Tension Pulley But Am Having A Hard Time Getting
(Posted by lisacarolross16 11 years ago)