Homelite UT43122 Support Question
Homelite UT43122 Support Question
Find answers below for this question about Homelite UT43122.Need a Homelite UT43122 manual? We have 3 online manuals for this item!
Question posted by jasonchamberlin on May 24th, 2015
Reverse Chain Direction
ut43122 motor runs, chain rotates but does not cut. reverse chain direction. from owners manual page 29. great! nothing about how to reverse chain direction? HELP please.
Current Answers
Answer #1: Posted by TheWiz on May 25th, 2015 6:35 AM
TheWiz
Member since:
October 13th, 2011 Points: 25,383,434
Member since:
October 13th, 2011 Points: 25,383,434
You will need to remove the chain and flip it around. Instructions on how to remove and replace the chain can be found on page 22 of the User's Manual.
Related Homelite UT43122 Manual Pages
User Manual - Page 3
...reverse the plug. Cluttered areas invite accidents.
Keep ALL children, bystanders, visitors, and animals out of the work should be aware of electric shock, this unit until you have a clear work area, secure footing, and a planned retreat path from chain and operator at least 14 is running...manual. Wear snug fitting clothing. Do not operate the chain...the motor or catch the chain ...
User Manual - Page 5
...the wood closes in and pinches the saw chain is running .
Contact at the upper portion of ...chain saw user, you are operating the saw control which kicks the guide bar up and back toward the operator. Hold the saw handles.
ROTATIONAL...and stop the chain for an instant. Make sure that are cutting is a lightning fast, reverse reaction which can cause the chain to minimize kickback:...
User Manual - Page 6
...cutting where the SAFE-T-TIP® would have to the direction the chain is moving where wood contact is a chain that is generated. Use only the replacement guide bars and low kickback chains... rotational kickback.
Follow the sharpening and maintenance instructions for the saw in this operator's manual. As saw chain is made. GUIDE BARS
Generally, guide bars with rotational kickback...
User Manual - Page 8
...
no
.../min
Keep Bystanders Away
Volts Amperes Hertz Watt Minutes Alternating Current Direct Current No Load Speed Class II Construction Per Minute
Keep all bystanders and...etc., per second) Power Time Type of current Type or a characteristic of current Rotational speed, at least 50 ft. Proper interpretation of these symbols will allow you ... handling the chain saw.
away. English
User Manual - Page 10
...A solid railed structure that transmits motion from a rotating source of the saw chain in the cut in and pinches the saw . Rear Handle
The ...manually actuated. Switch Lock-out
A movable stop that is driven by the motor and is supported by the guide bar. Saw Chain
A loop of chain having cutting teeth that cut in performing the bucking and felling cuts.
Felling
The process of cross cutting...
User Manual - Page 11
... 7-tooth Input 120 V, AC only, 60 Hz, 9 Amps Chain oil tank capacity 6 oz. UT43122 Bar length 16 in . Chain type Low Profile Skip Tooth Drive sprocket 7-tooth Input 120V, AC only, 60 Hz, 12 Amps Chain oil tank capacity 6 oz. No bar, chain, or lubricant...........8.5 lbs. Weight - Chain gauge 050 in . English
Fig. 6
SAFE-T-TIP®...
User Manual - Page 12
...Chain Saw Sleeve (Model UT43102 only) Scabbard (Model UT43122 only) Storage Bag (Model UT43122 only) Operator's Manual
WARNING:
If any parts on the Packing List are attempting. LOW KICKBACK SAW CHAIN
The low kickback saw chain helps minimize the force of the chain...manual as well as a knowledge of this list are included.
Use of the project you are already assembled to prevent the motor...
User Manual - Page 16
... operator's manual or received adequate instructions for damaged or dead branches that could result in the desired direction.
n Felling a tree - Wait until the hazardous weather has ended. n Operator should be felled in the felling area. n Allow the chain to stop. WORK AREA PRECAUTIONS
See Figure 12. Leave this operation for professionals. ■n Cut only...
User Manual - Page 17
... path, but watch your footing.
English
This notch should begin to open the cut (approximately 2 in the desired direction or it is deep enough for overhead limbs falling and watch the action in ...stop cutting before it may not fall . Make the notch cuts so they do not touch the chain. or 1/10 the diameter of large limbs. Page 17 - As the felling cut gets close to help jack...
User Manual - Page 23
... guide bar up and tighten the chain cover lock knob.
≈ .050 in the direction of the guide bar up and retighten the chain cover lock knob. NOTE: If chain is running. The cutters should still be turned by turning the chain tensioning knob clockwise until sag does not exist.
rotate knob clockwise to come loose, resulting...
User Manual - Page 25
... with the top plate of the bar. WARNING:
Failure to file all left hand cutters in the opposite direction. n Tension the chain prior to the same length, as fast cutting can cause excessive motor speed during cutting, which could cause serious injury.
MAINTENANCE
SHARPENING THE CUTTERS
See Figures 38 - 41. Be careful to replace or...
User Manual - Page 28
... teeth of the bar, the SAFE-T-TIP also helps keep the chain away from corrosive agents such as shown before storing or transporting the chain saw in a well-ventilated place that is inaccessible to preventing chain contact with ground cutting.
n Model UT43122 only: Place chain saw . TIGHTEN 3/4 OF A
TURN
MODEL UT43122 ONLY
Fig. 49
STORAGE BAG OPENINGS
ZIPPER...
User Manual - Page 29
... prior to shipment to Adjusting Chain Tension earlier in this manual. Refer to adjust chain tension. Chain tension too tight. Motor runs, chain Dull chain.
English Check chain tension for damage.
Motor runs, but does not cut.
Reverse direction of guide bar while rotating tension adjustment dial.
Press in the clutch cover lock knob and rotate counterclockwise to slightly loosen the...
User Manual 2 - Page 1
UT43102 AND UT43122
ALL VERSIONS REPAIR SHEET HOMELITE ELECTRIC CHAIN SAW MODEL NOS.
User Manual 2 - Page 2
HOMELITE CHAIN SAW - MODEL NUMBERS UT43102 AND UT43122 − ALL VERSIONS
1
12 9 11 10
98
SEE NOTE
9 76 5
2 17
19
18
3 4
SECTION "A"
14 13
15 16
2
User Manual 2 - Page 3
with SAFE-T-TIP)...1
SAFE-T-TIP...1
Chain Cover Assembly...1
Adjustment Gear...1
Gasket...1
Scabbard (UT43122)...1 Soft Case (UT43122)...1 Sleeve (UT43102)...1
NOTE: The assembly shown represents an important part of alteration or damage to the system, service should be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your...
User Manual 2 - Page 4
... UT43122 − ALL VERSIONS
SECTION "A"
12
1
8
15
13
1
15
20
2
7 3
4
5
6
11
18
19
15
9
10
28 29...
17
17
24
23
22
16
27
15
25
26
21
15 14
Section "A" represents an important part of the double insulated system of this tool requires dielectric testing to insure customer safety and to comply with company requirements.
4 Any repair to this tool. HOMELITE CHAIN...
User Manual 2 - Page 5
... 33904154G 32908154G 988000402 3-24-11 (REV:01)
DESCRIPTION
QTY
Rubber Pin 4 Motor Assembly (UT43102 1 Motor Assembly (UT43122 1 Cord Clamp 1 Icon Strip 1 Front Handle 1 Guard 1 Outlet Oil Tube 1 Oil Pump 1 Ring Gear Cover 1 Chain Bar Stud 1 Screw (M4.2 x 45 mm 1 Pinion 1 Retaining Ring 1 Operator's Manual
5 PARTS LIST FOR SECTION "A"
KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14...
User Manual 2 - Page 6
MODEL NUMBERS UT43102 AND UT43122 − ALL VERSIONS
WIRE NUT
WHITE
SWITCH BLACK
MOTOR
POWER CORD
BLACK
WIRING DIAGRAM
6 HOMELITE CHAIN SAW -
Replacement Parts List - Page 2
MODEL NUMBERS UT43102 AND UT43122 − ALL VERSIONS
1
SEE NOTE VOIR LA NOTE VEA LA NOTA
12 9 11 10
98
9 76 5
2 17
19
18
3 4
14 13
15 16
2 HOMELITE CHAIN SAW -
Similar Questions
Adjustment For Bar Oil Electric Pole Chain Saw Ut43160-a
electric pole chain saw ut43160-aoil tank empties in 10 mins of useis there an adjustment for bar oi...
electric pole chain saw ut43160-aoil tank empties in 10 mins of useis there an adjustment for bar oi...
(Posted by swgar 8 years ago)
How To Replace Trigger On Homelite Pole Chain Saw
How to replace trigger in handle on homelite pole chainsaw?
How to replace trigger in handle on homelite pole chainsaw?
(Posted by ruthdavis550 9 years ago)
Remove Safety Switch On Lawn Mower
how do I remove the safety switch on my electric, 20 inch, 24 v, cordless lawn mower? saftey switch ...
how do I remove the safety switch on my electric, 20 inch, 24 v, cordless lawn mower? saftey switch ...
(Posted by janiceaia 11 years ago)