Homelite UT49102 Support Question
Homelite UT49102 Support Question
Find answers below for this question about Homelite UT49102.Need a Homelite UT49102 manual? We have 3 online manuals for this item!
Question posted by janiceaia on April 14th, 2013
Remove Safety Switch On Lawn Mower
how do I remove the safety switch on my electric, 20 inch, 24 v, cordless lawn mower? saftey switch is on the bottom of a bar near top handle.
Current Answers
Related Homelite UT49102 Manual Pages
User Manual - Page 5
...is used outdoors, use only extension cords with padlocks, master switches, or by a qualified service technician at least 14 is ... conductor. Never use of the electric cord or plug is damaged should wear safety glasses and be properly repaired or... TOOLS. If damaged, have only impactresistant lenses, they are removed from work into moving parts, breakage of power and overheating....
User Manual - Page 6
...RAM-TYPE log splitters, NEVER attempt to be located by the carrying handle. Use only recommended accessories listed in
this tool, loan them...; CIRCUIT CAPACITY AND FUSES: a) Use only an electrical circuit having adequate capacity as required to prevent unintended ...your tool) to power supply. GENERAL SAFETY RULES
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF....
User Manual - Page 7
...wear nonslip, heavy-duty protective gloves when operating this product.
Always wear nonslip safety footwear when operating this product.
10' 3m
Keep Bystanders Away
Always keep hands... this product.
Please study them and learn their meaning. Precautions that involve your safety. SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles...
User Manual - Page 8
... completely the operator's manual. Call Homelite customer service for use over eyeglasses or standard safety glasses with side shields and, when needed, a full face shield.
If you return...Z87.1. Always use this product.
SAVE THESE INSTRUCTIONS
6 - We recommend Wide Vision Safety Mask for assistance. English
SYMBOLS
The following signal words and meanings are intended to...
User Manual - Page 9
...is properly installed and grounded in figure 1. Do not operate this tool on 12 gauge - 20 amp circuit. Use the chart provided below to overheat. NOTE: AWG = American Wire Gauge... of the working with all local codes and ordinances. A line intended only for use . Electrical
Extension Cords
Use only 3-wire extension cords that have the proper outlet installed by a qualified electrician...
User Manual - Page 10
....
KNOW YOUR LOG SPLITTER
See Figure 2. LIFT HANDLE
The lift handle makes rolling the log splitter from the
box. ...Diameter, minimum 4 in . Log Capacity Length 20.5 in a hazardous condition leading to restart the machine. Remove the load and push the reset/overload button...the wedge. Make sure that all operating features and safety rules. PACKING LIST
Log Splitter Wheel (2) Hardware Bag...
User Manual - Page 11
... THE wheels
See Figure 3. To attach the wheels to secure the wheel assembly. remove the hitch pin from rupturing.
n Lift the machine slightly and slip the axle ...safety glasses with tools to hold down the on /off switch.
Never operate the log splitter until the center of the pin rests on the end with the second wheel assembly. diameter or 20-1/2 in figure 7. n Using the lift handle...
User Manual - Page 12
...10 -
WARNING:
Always wear safety goggles or safety glasses with plastic parts.
LUBRICATION
All of use. REPLACING HYDRAULIC OIL
See Figures 12 - 13. n Using an 8 mm hex key, remove the oil drain bolt.
...to return the ram to the starting position. n Drain the hydraulic oil from either the switch or the lever, the log splitter will heat and can damage, weaken or destroy plastic ...
User Manual - Page 13
... log splitter.
3. Contact the dealer.
1.
TROUBLESHOOTING
Problem
Motor fails to "Sharpening Wedge" in the Maintenance section.
4.
Wedge cutting edge is improperly positioned.
2. Contact the dealer. 5. Remove and check the oil level. Tighten securely.
Overload Protection Device is disengaged to Operation section for some time, it from being damaged. Log is blunt...
User Manual - Page 14
... Reels, Starter Pulleys, Starter Ropes, Drive Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower Fans, Blower and Vacuum Tubes, Vacuum Bags and Straps, Guide Bars, Saw Chains
Homelite reserves the right to change or improve the design of purchase will be performed by a Homelite authorized service center. This warranty does...
Maintenance Guide - Page 1
1
addendum
Electric Log Splitter
UT49102
Fig.1
2
troubleshooting
If the Hydraulic Control Lever does not return to its original up position after it retracts.
Fig. 2
3
B
987000-823 8-04-09 (REV:00)
...
Similar Questions
Previous Owner Removed Capacitor . How Do I Reconnect It In Terminal Block. Can'
can't seem to put leads from capacitor into terminel block even after loosening screws
can't seem to put leads from capacitor into terminel block even after loosening screws
(Posted by bk4520 1 year ago)
Replacing The Momentary Stop Switch
I am ready to reinstall the new stop switch but I do not remember which wire is connected to which e...
I am ready to reinstall the new stop switch but I do not remember which wire is connected to which e...
(Posted by Melissadee78 6 years ago)
How To I Remove The Spool Head From The Shaft?
I want to replace the spool head with a plastic blade unit. How does the head come off?
I want to replace the spool head with a plastic blade unit. How does the head come off?
(Posted by Bsackett 7 years ago)
When I Start My Ut49103 The Motor Turns Off And The Switch Pops Out. What Do I D
(Posted by ismaeljauregui 9 years ago)