Hitachi NT65GS Support Question
Hitachi NT65GS Support Question
Find answers below for this question about Hitachi NT65GS - 2-1-2" 16 Gauge Gas Powered Straight Finish Nailer.Need a Hitachi NT65GS manual? We have 2 online manuals for this item!
Question posted by xpertcarpentry on July 10th, 2012
Pin Keeps Popping Out
the pin in the gun keeps popping out. if i flip open the top and push the pin back in it pops again as soon as i shoot a nail
Current Answers
Related Hitachi NT65GS Manual Pages
Instruction Manual - Page 6
... propellant will
(50°C)
remain in the fuel cell. Respect the Nailer as a working implement.
6. KEEP FINGERS AWAY FROM TRIGGER WHEN NOT DRIVING FASTENERS TO AVOID ACCIDENTAL FIRING.
Do... flying objects.
8. Always carry the Nailer by the handle only.
7.
Do not inhale.
9. The device may burst, releasing flammable gas.
NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA...
Instruction Manual - Page 7
... 8 inches (200 mm) from work areas of children. Rubber gloves and nonskid footwear are missing or damaged.
16.
The Push lever operation becomes especially heavy in moving parts. Keep all work area.
13. and 3) keep the Nailer pointed downward.
17. DO NOT DRIVE FASTENERS INTO THIN BOARDS OR NEAR CORNERS AND EDGES OF WORKPIECE. English...
Instruction Manual - Page 8
... unattended since people who are not familiar with its operation or unauthorized personnel.
22. NEVER USE NAILER FOR APPLICATIONS
Keep proper footing and balance at all remaining fasteners from the Nailer. NEVER USE NAILER WHICH IS DEFECTIVE OR OPERATING ABNORMALLY. Keep the Nailer clean and lubricated for repairs by Hitachi,
distributor or employer shall repair the...
Instruction Manual - Page 9
...with skin ; In case of being inhaled ; In case of the tool and disposal.
Do not dispose of children.
9
direct sunlight or ...combustible gas for the purpose of storage, transportation, inserting into a comfortable position. Explosion / Fire Hazard
Failure to an open air ...Keep out of reach of fuel cell with warm water and soap and apply a skin cream when dry. Do not puncture or open...
Instruction Manual - Page 11
... generator or DC power to the battery charger may reach or exceed 104°F (40°C).
12. English
SAFETY - NEVER
disassemble the battery. NEVER use the Nailer. Do not use... the charger on standard household electrical power (120 volts). Use the battery charger correctly. The battery charger is low humidity and good ventilation. Keep your attention from direct sunlight and ...
Instruction Manual - Page 12
... SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
12 Ensure that Nailers are used before repair. Keep Nailers in work area.
4. The product that Nailers which require repair
are wearing EYE PROTECTOR.
3. At the end of EYE PROTECTOR...no expose the battery charger to use to direct sunlight during charging. Maintain Nailers properly. 6.
Instruction Manual - Page 16
... below can be driven with this Nailer. The use only the genuine HITACHI nails for the NT65GS, NT65GB, NT65GA or the NT50GS. Only nails shown in tool malfunction and/or nail breakdown, leading to use of nails
16 Gauge finish nails (straight)
Min. .110" (2.8mm)
Max.
2-1/2" (65mm)
1" (25mm) .051" (1.3mm)
.055" (1.4mm)
.065" (1.65mm)
16 Gauge finish nails (Angle: 20°)
Min. .110...
Instruction Manual - Page 21
...
any incandescent
material.
ⅷ Do not smoke
when handling
fuel cell.
ⅷ Keep stem of children.
DANGER
ⅷ The fuel cell is not recommended for use . CAUTION ⅷ If the gas leaks from
ignition sources.
Do not inhale.
ⅷ Keep the Nailer,
120°F MAX fuel cell and
(50°C)
battery away from sunshine...
Instruction Manual - Page 24
...8554; THE NAILER MUST OPERATE PROPERLY.
(4) Remove the finger from the workpiece. Swing back
(7) If no abnormal operation is the same type to pulling back nail feeder)
Ⅺ THE NAILER MUST NOT OPERATE. English
4 Close the actuator. 2. and 3) keep Nailer pointed downward.
2-Action Nail Feeding! (1) Insert nail strip into Nailer, 1) do not pull trigger; 2) do not depress push lever;
Instruction Manual - Page 25
... Nailer is now ready to the nail strip.
Always keep
the points of nails in contact with Groove.
1
2 Nail feeder (A)
Nail feeder (B)
Nail strip
Magazine Groove
NOTE: ⅷ The nails shown in contact with nails of more than 10 nails. ⅷ Use an unbroken nail strip with Groove.
25 English
3
Nail feeder (B) Nail feeder (A)
NOTE: ⅷ Quietly push the nail feeder (A) and nail...
Instruction Manual - Page 26
NAILER OPERATION
Read section titled "SAFETY"(pages 5 - 12). WARNING
ⅷ NEVER point tool at yourself or others in work area.
ⅷ Keep fingers AWAY from
ignition source.
ⅷ No smoking. Nail strip Blade guide
(4) Confirm that nail strip is placed with bare hands.
The push lever
and nose will
become hot and
get heated up
after prolonged...
Instruction Manual - Page 31
... maintenance of flammable liquids or gases.
ⅷ Keep away from Nailer when: 1) doing maintenance and inspection; Remove dust and
wooden chips which may show details or attachments that the nail feeder slides smoothly by pulling it with Hitachi Gas tool lubricant.
DANGER
ⅷ Never use ,
(50°C)
the Nailer, fuel
cell and battery
should be driven...
Instruction Manual - Page 32
... rust.
⅜ Do not store the Nailer, fuel cell and battery in a cold weather environment. In the operation and maintenance of power tools, the safety regulations and standards prescribed in ...For continued protection against risk
of fire, replace only with the tool to incorporate the latest technological advancements. Keep it out of reach of cigarette lighter connecting plug
Warning label
...
Instruction Manual - Page 33
...a jam.
Operator troubleshooting
PROBLEM Nailer operates, but no nail is bent. Driven nail is driven. Check function of nail feeder per page 31.
Push the driver blade with a ... Keep push lever working Promote operator safety and Blow clean daily.
properly.
Skipping nails. The operation of piston smoothly.
CHECK METHOD Check for replacement. Check function of nail ...
Instruction Manual - Page 105
...HD. NT65GS
ITEM NO.
SOCKET SET SCREW M4×5
2
23 SHAFT RUBBER WASHER
1
24A SHAFT COVER
1
25 PISTON RING (A)
2
26 PISTON
1
27 PISTON BUMPER
1
28 NAME PLATE
1
29 HOUSING
1
30 PIN
1
...ROLL PIN D3×16
92 RIBBON SPRING
93 NAIL FEEDER (B)
94 PRISM
95 CONTROLLER
96 TAPPING SCREW (W/FLANGE) D4×12
97 NAIL RAIL
98 PUSHING SPRING
99 NAIL FEEDER (A)
100 ROLL PIN D2...
Instruction Manual - Page 107
...
SEAL LOCK HEX. SCREW M4
89 ROLL PIN D3×16
90 RIBBON SPRING
91 NAIL FEEDER (B)
92 NAIL FEEDER (A)
93 PUSHING SPRING
94 ROLL PIN D2.5×26
95 PRISM
96 CONTROLLER
97 TAPPING SCREW (W/FLANGE) D4×12
98 NAIL RAIL
99 MAGAZINE
100 PUSH STOPPER (A)
101 LOCK SPRING
102 PUSH STOPPER COVER
103 TAPPING SCREW (W/FLANGE...
Instruction Manual - Page 109
... SCREW M5×15
89 ROLL PIN D3×16
90 RIBBON SPRING
91 NAIL FEEDER (B)
92 NAIL FEEDER (A)
93 STOPPER SPRING (C)
94 PRISM
95 CONTROLLER
96 TAPPING SCREW (W/FLANGE) D4×12
97 NAIL RAIL
98 ROLL PIN D2.5×26
99 MAGAZINE
100 PUSH STOPPER (B)
101 PUSH STOPPER SPRING
102 PUSH STOPPER COVER
103 TAPPING SCREW (W/FLANGE...
Instruction Manual - Page 111
... 2
35 LOCK LEVER COVER
1
36 GUIDE PLATE
1
37 ROLL PIN D3×10
1
38 LOCK LEVER
1
39 ROLL PIN D3×16
1
40 HEX. SOCKET HD. BOLT M4×10 2
79 PUSH LEVER ARM
1
80 PUSH LEVER PIECE
1
81 O-RING (S-8)
1
82 ADJUSTER
1
83 RATCHET SPRING
2
84 PUSHING LEVER (A)
1
85 CAUTION LABEL
1
86 WARNING LABEL
1
87 CONTROLLER...
Parts List - Page 2
...949-754 HEX. BOLT M4X16 (10 PCS.)
4
14 886-295 CHAMBER HEAD
1
15 886-296 GASKET
1
16 886-297 CHAMBER
1
17 886-312 PISTON RING (B)
4
18 886-298 RETAINING RING FOR D40 HOLE
1
...886-291 PISTON
1
27 886-289 PISTON BUMPER
1
28
NAME PLATE
1
29 886-549 HOUSING
1
30 886-310 PIN
1
31 886-302 BLADE GUIDE
1
32 886-311 SEAL LOCK HEX.
USED
1
REMARKS
2 886-344 FILTER MESH...
Parts List - Page 4
.... BAR WRENCH 3MM
505 886-349 NOSE CAP (A)
506 886-348 CASE
* 507 886-036 LUBRICANT OILER (B)
NO. DESCRIPTION
99 886-339 NAIL FEEDER (A)
100 886-334 ROLL PIN D2.5X24
101 886-336 MAGAZINE
102 886-550 CYLINDER ASS'Y (A)
103 875-638 O-RING (S-12)
104 886-668 CYLINDER HEAD ASS'Y
NO...
Similar Questions
Just Bought A New Regulator Installed It And Air Is Leaking Out Of The Pin Holeo
the pin hole on the round part that butts to cover plate that holds it on
the pin hole on the round part that butts to cover plate that holds it on
(Posted by Johnjaboor 2 years ago)
Screeching Noise
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
(Posted by Rongowrie 2 years ago)
Hitachi Nt65gs
hi wondering if anybody has any information on how to strip down and rebuild the hitachi pin gun or ...
hi wondering if anybody has any information on how to strip down and rebuild the hitachi pin gun or ...
(Posted by sedgiejunior 3 years ago)
Nail Striker Pin Jams
The striker pin get stuck in front of the nails. I have to push it back with a small screw driver. T...
The striker pin get stuck in front of the nails. I have to push it back with a small screw driver. T...
(Posted by caseyrealtytrust 6 years ago)
Driver Pin Problem
my driver pin retracts when air is disconnected then fully contracts out when air is plugged in, wit...
my driver pin retracts when air is disconnected then fully contracts out when air is plugged in, wit...
(Posted by tommyplewka 8 years ago)